Personal tools

SL-TFT7-TP-800-480 Datasheet and Pinout

From SomLabs Wiki

Jump to: navigation, search

Display module SL-TFT7-TP-800-480 Datasheet and Pinout


General description

SL-TFT7-TP-800-480-front-rocks.png


SL-TFT7-TP-800-480 is complete display TFT-LCD (800x480 pixels) module integrated with capactive touch-panel. Module is powered from +5V @400mA, data interface is 24-bit parallel RGB + I2C (for touch-panel controller). SL-TFT7-TP-800-480 module is equpiied with FPC50 connector, 1:1 compatible with VisionCB-STD v.1.0 and VisionCB-STD v.1.4. SOMLabs also provides a complete hardware and software development board for the SoM in the form of a carrier board and optional TFT display and touch-panel.

Features

  • Powered by Powertip PH800480T013-IBC15 LCD-TFT
  • Display size 7 inches
  • Display LCD matrix 800x480 px
  • Capacitive touch-panel + TP controller
  • 24-b RGB parallel interface
  • Single supply +5V (DC/DC converters built-in)
  • Backlight LEDs built-in
  • Compatible with SoMLabs carrier boards:
    • VisionCB-STD v.1.0
    • VisionCB-STD v.1.4

Multimedia



Pictures

SL-TFT7-TP-800-480-front-empty-shop.jpg
SL-TFT7-TP-800-480-front-rocks-shop.jpg
SL-TFT7-TP-800-480-front-disindis-shop.jpg
SL-TFT7-TP-800-480-stand2.jpg

Ordering info

SL-TFT7-TP-800-480 - FPC 50-pin 15-cm flat cable (A-A) is included.

Operating ranges

Parameter Value Unit Comment
Power Supply
5.0
V
-
Current
0.4
A
Maximum value, depends on displayed picture and backlight light intensity
Video input voltage
max. 3.3
V
Touch panel controller IO voltage
max. 3.3
V
I2C interface, 2.2kΩ pull-up resistor on SDA and SCL lines
Environment temperature
-20…+75
oC -

Electrical parameters

Signal name Parameter Value Units
Min. Typ. Max.
+5V Supply Voltage 4.0 5.0 5.5 V
- Total Supply Current 230 330 400 mA
VIO Video IO Input Voltage 0 3.3 3.6 V
VTPIO TP Controller IO Voltage 0 3.3 3.6 V
VPWREN Power Enable Input Voltage 0 - 5.5 V
fTPI2C TP Controller I2C Speed - - 400 kHz
fPWM PWM Dimming Frequency - - 1 kHz
RINT Interrupt Output Pull-up Resistance - 10 -
RPWREN Power Enable Pull-up Resistance - 10 -
RTPI2C Touch Panel Controller I2C IOs Pull-up Resistance - 2.2 -

Pinout

Sl-tft7-tp-800-480-pin1.jpg

FPC50 connector pin Function name Description
1 B0 Blue 0 input
2 B1 Blue 1 input
3 B2 Blue 2 input
4 B3 Blue 3 input
5 B4 Blue 4 input
6 B5 Blue 5 input
7 B6 Blue 6 input
8 B7 Blue 7 input
9 GND Power supply
10 G0 Green 0 input
11 G1 Green 1 input
12 G2 Green 2 input
13 G3 Green 3 input
14 G4 Green 4 input
15 G5 Green 5 input
16 G6 Green 6 input
17 G7 Green 7 input
18 GND Power supply
19 R0 Red 0 input
20 R1 Red 1 input
21 R2 Red 2 input
22 R3 Red 3 input
23 R4 Red 4 input
24 R5 Red 5 input
25 R6 Red 6 input
26 R7 Red 7 input
27 GND Power supply
28 DE DE display controller input
29 HSYNC HSYNC display controller input
30 VSYNC VSYNC display controller input
31 GND Power supply
32 DCLK Main clock input (display controller)
33 GND Power supply
34 - -
35 - -
36 nINT Touch-panel controller interrupt output (OC with 10kΩ pull-up)
37 GPIO1 PWM signal input for backlight control (leave open if not used)
38 - -
39 - -
40 - -
41 - -
42 SCL Touch-panel controller SCL input (with 2.2kΩ pull-up)
43 SDA Touch-panel controller SDA IO (with 2.2kΩ pull-up)
44 GND Power supply
45 NC No external connections!
46 NC No external connections!
47 +5V Power supply
48 +5V Power supply
49 nRES_TP Touch-panel controller reset signal
50 PWREN Backlight LEDs on/off, with 10kΩ pull-up resisitor (level +5V).
If PWREN pin is open or connected to "1" - LEDs are on.

Recommended power supply connection

SL-TFT7-TP-800-480-connection-5V.png

Dimensions

SL-TFT7-TP-800-480-wymiary.png
NXP Partner ST Partner