VisionCB-RT-STD v.1.0 Datasheet and Pinout - Revision history

Piotrzbysinski: /* Electrical parameters */

2020-07-09T13:11:52Z

Electrical parameters

2020-07-09T13:11:19Z

Electrical parameters

← Older revision		Revision as of 13:11, 9 July 2020
Line 92:		Line 92:
	\| 9.0		\| 9.0
	\| 11.0		\| 11.0
	\| 12.0		\| 15.0
	\| V		\| V
	\| Positive pole on central connector of J100		\| Positive pole on central connector of J100

2019-09-13T08:02:56Z

Electrical parameters

@@ Line 102: / Line 102: @@
 | A
 | Excluding LCD, USB and antoher external loads
 |-
 | USB power supply

2019-09-13T07:59:26Z

Arduino compatible I/O headers (J500-J503)

2019-09-13T07:58:44Z

Electrical parameters

← Older revision		Revision as of 07:58, 13 September 2019
Line 127:		Line 127:
	\| 0		\| 0
	\| -		\| -
	\| 3.3/5		\| 3.3/5 (1)
	\| V		\| V
	\| Arduino compatible connector (digital I/O)		\| Arduino compatible connector (digital I/O)
Line 138:		Line 138:
	\| Arduino compatible connector (analog inputs)		\| Arduino compatible connector (analog inputs)
	\|}		\|}

			Note:<br/>
			1. Depends on JP3 selector.<br/>

	== Boot Selector ==		== Boot Selector ==

2019-09-13T07:56:47Z

TFT LCD connector (RGB 24b, J405)

← Older revision		Revision as of 07:56, 13 September 2019
Line 1,088:		Line 1,088:
	\| VCC-LCD		\| VCC-LCD
	\| -		\| -
	\| +3.3V (controlled by ~~GPIO_ADB0_11~~/JTAG-TRSTB)		\| +3.3V (controlled by GPIO_AD_B0_11/JTAG-TRSTB)
	\|-		\|-
	\| 46		\| 46
	\| VCC-LCD		\| VCC-LCD
	\| -		\| -
	\| +3.3V (controlled by ~~GPIO_ADB0_11~~/JTAG-TRSTB)		\| +3.3V (controlled by GPIO_AD_B0_11/JTAG-TRSTB)
	\|-		\|-
	\| 47		\| 47
Line 1,116:		Line 1,116:
	\|}		\|}
	Note:<br/>		Note:<br/>
	1. When ~~GPIO_ADB0_11~~/JTAG-TRSTB:<br/>		1. When GPIO_AD_B0_11/JTAG-TRSTB:<br/>
	= '1' LCD module power supply is OFF.<br/>		= '1' LCD module power supply is OFF.<br/>
	= '0' LCD module power supply is ON.<br/>		= '0' LCD module power supply is ON.<br/>

2019-09-13T07:55:56Z

TFT LCD connector (RGB 24b, J405)

← Older revision		Revision as of 07:55, 13 September 2019
Line 1,115:		Line 1,115:
	\| PWREN		\| PWREN
	\|}		\|}
			Note:<br/>
			1. When GPIO_ADB0_11/JTAG-TRSTB:<br/>
			= '1' LCD module power supply is OFF.<br/>
			= '0' LCD module power supply is ON.<br/>

	== Dimensions ==		== Dimensions ==
	[[File:VisionCB-RT-STD-1-0-PCB-size.png\|800px\|center]]		[[File:VisionCB-RT-STD-1-0-PCB-size.png\|800px\|center]]

2019-09-13T07:51:06Z

TFT LCD connector (RGB 24b, J405)

← Older revision		Revision as of 07:51, 13 September 2019
Line 1,088:		Line 1,088:
	\| VCC-LCD		\| VCC-LCD
	\| -		\| -
	\| +3.3V (controlled by ~~ENET2_TXEN~~)		\| +3.3V (controlled by GPIO_ADB0_11/JTAG-TRSTB)
	\|-		\|-
	\| 46		\| 46
	\| VCC-LCD		\| VCC-LCD
	\| -		\| -
	\| +3.3V (controlled by ~~ENET2_TXEN~~)		\| +3.3V (controlled by GPIO_ADB0_11/JTAG-TRSTB)
	\|-		\|-
	\| 47		\| 47

2019-09-13T07:48:51Z

Arduino compatible I/O headers (J500-J503)

← Older revision		Revision as of 07:48, 13 September 2019
Line 601:		Line 601:
	\| VCC-3V3		\| VCC-3V3
	\| -		\| -
	\| ~~Referrence~~ voltage +3.3V generated by internal SOM LDO converter (load current limited to 500 mA).		\| Reference voltage +3.3V generated by internal SOM LDO converter (load current limited to 500 mA).
	\|-		\|-
	\| 5		\| 5
Line 607:		Line 607:
	\| VCC-5V0		\| VCC-5V0
	\| -		\| -
	\| ~~Referrence~~ voltage +5V generated by carrier board built-in DC/DC converter.		\| Reference voltage +5V generated by carrier board built-in DC/DC converter.
	\|-		\|-
	\| 6		\| 6

2019-09-13T07:48:10Z

Arduino compatible I/O headers (J500-J503)

← Older revision		Revision as of 07:48, 13 September 2019
Line 777:		Line 777:

	Notes:<br />		Notes:<br />
	1. All I/O lines are 5V compatible.<br />		1. Depends on MCU type.
	2. RESET line is 5V compatible.<br />		2. All digital I/O lines are 5V compatible.<br />
	3. Preferred voltage range on AIN0…AIN3 lines is 0…+3.3V.<br />		3. RESET line is 5V compatible.<br />
	4. Voltage level compatibility can be changed to +3.3V ~~with removing R901 and mouting R902 (0R)~~, but voltage range on AIN0…AIN3 lines must be 0…+3.3V.<br />		4. Preferred voltage range on AIN0…AIN3 lines is 0…+3.3V.<br />
			5. Voltage level compatibility can be changed to +3.3V by JP3 selector, but voltage range on AIN0…AIN3 lines must be 0…+3.3V.<br />

	== User LEDs connections ==		== User LEDs connections ==