Writing StarSBC-6ULL system image to eMMC memory - Revision history

KrzysztofChojnowski at 09:05, 12 December 2022

2022-12-12T09:05:51Z

← Older revision		Revision as of 09:05, 12 December 2022
Line 3:		Line 3:

	* A complete package with NXP UUU application - [http://ftp.somlabs.com/VisionSOM-6ULL/uuu-visionsom-6ull.zip uuu-visionsom-6ull.zip]		* A complete package with NXP UUU application - [http://ftp.somlabs.com/VisionSOM-6ULL/uuu-visionsom-6ull.zip uuu-visionsom-6ull.zip]
	* Built and extracted system image file called image.wic (from Yocto build tmp/deploy/images/starsbc-6ull/somlabs-image-starsbc-6ull.wic.~~bz2~~)		* Built and extracted system image file called image.wic (from Yocto build tmp/deploy/images/starsbc-6ull/somlabs-image-starsbc-6ull.wic.zst)
	* Built bootloader binary u-boot.imx (from Yocto build tmp/deploy/images/starsbc-6ull/u-boot.imx)		* Built bootloader binary u-boot.imx (from Yocto build tmp/deploy/images/starsbc-6ull/u-boot.imx)

KrzysztofChojnowski at 09:05, 12 December 2022

2022-12-12T09:05:01Z

← Older revision		Revision as of 09:05, 12 December 2022
Line 27:		Line 27:

	[[File:Starsbc_6ull_program_emmc_1.jpg\|center\|300px]]		[[File:Starsbc_6ull_program_emmc_1.jpg\|center\|300px]]
			[[File:Starsbc_6ull_program_emmc_2.jpg\|center\|300px]]
	~~TODO Programming PADS picture~~

	The pads need to be shortcuted until the uuu programming process starts.		The pads need to be shortcuted until the uuu programming process starts.

	After the process is done the board may be reset to start the programmed image.		After the process is done the board may be reset to start the programmed image.

KrzysztofChojnowski at 11:00, 17 February 2022

2022-02-17T11:00:36Z

← Older revision		Revision as of 11:00, 17 February 2022
Line 25:		Line 25:

	connect the board to the PC using the microUSB port with connected pads on the bottom side of the module.		connect the board to the PC using the microUSB port with connected pads on the bottom side of the module.

			[[File:Starsbc_6ull_program_emmc_1.jpg\|center\|300px]]

	TODO Programming PADS picture		TODO Programming PADS picture

KrzysztofChojnowski: Created page with "{{PageHeader|Writing system image to eMMC memory}} == Prerequisites == * A complete package with NXP UUU application - [http://ftp.somlabs.com/VisionSOM-6ULL/uuu-visionsom-6u..."

2022-02-03T14:20:08Z

Created page with "{{PageHeader|Writing system image to eMMC memory}} == Prerequisites == * A complete package with NXP UUU application - [http://ftp.somlabs.com/VisionSOM-6ULL/uuu-visionsom-6u..."

New page

{{PageHeader|Writing system image to eMMC memory}}
== Prerequisites ==

* A complete package with NXP UUU application - [http://ftp.somlabs.com/VisionSOM-6ULL/uuu-visionsom-6ull.zip uuu-visionsom-6ull.zip]
* Built and extracted system image file called image.wic (from Yocto build tmp/deploy/images/starsbc-6ull/somlabs-image-starsbc-6ull.wic.bz2)
* Built bootloader binary u-boot.imx (from Yocto build tmp/deploy/images/starsbc-6ull/u-boot.imx)

== Information ==
The [http://ftp.somlabs.com/VisionSOM-6ULL/uuu-visionsom-6ull.zip uuu-visionsom-6ull.zip] archive contains the compiled NXP uuu binary for Linux, the commands script and the bootloader supporting fastboot command. The script requires the image.wic and u-boot.imx files to be in the same directory.

=== Programming StartSBC-6ULL eMMC memory ===

For image programing, use one of the following commands.

On Linux host:
<pre>sudo ./uuu vsom-6ull-cmds</pre>

On Windows host:
<pre>uuu.exe vsom-6ull-cmds</pre>

After the uuu tool stops and the following message is displayed:

<pre>Wait for Known USB Device Appear...</pre>

connect the board to the PC using the microUSB port with connected pads on the bottom side of the module.

TODO Programming PADS picture

The pads need to be shortcuted until the uuu programming process starts.

After the process is done the board may be reset to start the programmed image.