Difference between revisions of "VisionCB-x2L-STD Datasheet and Pinout"
From SomLabs Wiki
(→Features) |
(→RECOVERY jumper) |
||
(72 intermediate revisions by the same user not shown) | |||
Line 31: | Line 31: | ||
**ADC+GPIO connector 2x9 Pin Header (Male) | **ADC+GPIO connector 2x9 Pin Header (Male) | ||
**Raspberry Pi Compatible Connectors 2x20 Pin Header (Male) | **Raspberry Pi Compatible Connectors 2x20 Pin Header (Male) | ||
− | **Ethernet #1 Connector Pin Header (Male) | + | **Ethernet #1 (GMII) Connector Pin Header (Male) |
*Communication Connectors: | *Communication Connectors: | ||
**1x Ethernet 10/100/1000Mbit/s (RJ45) | **1x Ethernet 10/100/1000Mbit/s (RJ45) | ||
Line 72: | Line 72: | ||
{ | { | ||
"type" : "separator", | "type" : "separator", | ||
− | "value" : "VisionCB- | + | "value" : "VisionCB-x2L-STD v1.2" |
} | } | ||
] | ] | ||
Line 78: | Line 78: | ||
== Block Diagram == | == Block Diagram == | ||
− | [[File: | + | [[File:VisionCB-x2l-std-BLOKOWY.png|1000px|center]] |
== Electrical parameters == | == Electrical parameters == | ||
Line 97: | Line 97: | ||
| 15.0 | | 15.0 | ||
| V | | V | ||
− | | Positive pole on central connector of | + | | Positive pole on central connector of J200 |
|- | |- | ||
| Supply current | | Supply current | ||
| - | | - | ||
| - | | - | ||
− | | 0. | + | | 0.13 |
| A | | A | ||
| Excluding LCD, USB and antoher external loads | | Excluding LCD, USB and antoher external loads | ||
Line 114: | Line 114: | ||
|- | |- | ||
| LCD/Camera Power Supply<br>(backlight and aux) | | LCD/Camera Power Supply<br>(backlight and aux) | ||
− | | 4. | + | | 4.75 |
− | | | + | | 4.87 |
− | | | + | | 4.95 |
| V | | V | ||
| - | | - | ||
Line 122: | Line 122: | ||
| Arduino GPIO voltage | | Arduino GPIO voltage | ||
| | | | ||
− | | 3.3 | + | | 3.3 |
| | | | ||
| V | | V | ||
− | | | + | | - |
|} | |} | ||
</center> | </center> | ||
− | == | + | == Power supply connector == |
− | [[File: | + | The VisionCB-x2L-STD is equipped with external power source connector with pin diameter 2.5mm and hole diameter 6mm. The voltage of the external power source should be within the range 9-12 VDC. |
+ | [[File:VisionCB-x2L-STD-power-supply.png|center|800px]] | ||
+ | == Camera MIPI-CSI interface (FPC/FFC30, 0.5mm) == | ||
+ | [[File:VisionCB-x2L-STD-CSI.png|center|800px]] | ||
<center> | <center> | ||
Line 137: | Line 140: | ||
! style="text-align: center; font-weight: bold;" | Pin | ! style="text-align: center; font-weight: bold;" | Pin | ||
! style="text-align: center; font-weight: bold;" | Signal | ! style="text-align: center; font-weight: bold;" | Signal | ||
+ | ! style="text-align: center; font-weight: bold;" | GPIO | ||
! style="text-align: center; font-weight: bold;" | Description | ! style="text-align: center; font-weight: bold;" | Description | ||
|- | |- | ||
− | | 1 || GND || - | + | | 1 || GND || - || - |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | 2 || CSI-CLK-P || - | + | | 2 || CSI-CLK-P || - || - |
|- | |- | ||
− | | 3 || CSI-CLK-P || - | + | | 3 || CSI-CLK-P || - || - |
|- | |- | ||
− | | 4 || GND || - | + | | 4 || GND || - || - |
|- | |- | ||
− | | 5 || CSI-DATA0-P || - | + | | 5 || CSI-DATA0-P || - || - |
|- | |- | ||
− | | 6 || CSI-DATA0-N || - | + | | 6 || CSI-DATA0-N || - || - |
|- | |- | ||
− | | 7 || GND || - | + | | 7 || GND || - || - |
|- | |- | ||
− | | 8 || CSI-DATA1-P || - | + | | 8 || CSI-DATA1-P || - || - |
|- | |- | ||
− | | 9 || CSI-DATA1-N || - | + | | 9 || CSI-DATA1-N || - || - |
|- | |- | ||
− | | 10 || GND || - | + | | 10 || GND || - || - |
|- | |- | ||
− | | 11 || CSI-DATA2-P || - | + | | 11 || CSI-DATA2-P || - || - |
|- | |- | ||
− | | 12 || CSI-DATA2-N || - | + | | 12 || CSI-DATA2-N || - || - |
|- | |- | ||
− | | 13 || GND || | + | | 13 || GND || - || - |
|- | |- | ||
− | | 14 || CSI-DATA3-P || - | + | | 14 || CSI-DATA3-P || - || - |
|- | |- | ||
− | | 15 || CSI-DATA3-N || - | + | | 15 || CSI-DATA3-N || - || - |
|- | |- | ||
− | | 16 || GND|| - | + | | 16 || GND|| - || - |
|- | |- | ||
− | | 17 || | + | | 17 || I2C1-SCL || RIIC1_SCL || Camera confguration I2C interface (3.3V), pull-uped with 2.2k |
|- | |- | ||
− | | 18 || | + | | 18 || I2C1-SDA || RIIC1_SDA || Camera confguration I2C interface (3.3V), pull-uped with 2.2k |
|- | |- | ||
− | | 19 || GND || - | + | | 19 || GND || - || - |
|- | |- | ||
− | | 20 || | + | | 20 || CSI-GPIO0 || P17-0 || Auxiliary GPIO |
|- | |- | ||
− | | 21 || | + | | 21 || CSI-GPIO1 || P17-1 || Auxiliary GPIO |
|- | |- | ||
− | | 22 || - || - | + | | 22 || - || - || - |
|- | |- | ||
− | | 23 || GND || - | + | | 23 || GND || - || - |
|- | |- | ||
− | | 24 || +3.3V || Power supply for external devices | + | | 24 || +3.3V || - || Power supply for external devices |
|- | |- | ||
− | | 25 || +3.3V || Power supply for external devices | + | | 25 || +3.3V || - || Power supply for external devices |
|- | |- | ||
− | | 26 || +5V || Power supply for external devices | + | | 26 || +5V || - || Power supply for external devices |
|- | |- | ||
− | | 27 || +5V || Power supply for external devices | + | | 27 || +5V || - || Power supply for external devices |
|- | |- | ||
− | | 28 || - || - | + | | 28 || - || - || - |
|- | |- | ||
− | | 29 || - || - | + | | 29 || - || - || - |
|- | |- | ||
− | | 30 || GND || - | + | | 30 || GND || - || - |
|} | |} | ||
</center> | </center> | ||
Note: | Note: | ||
− | <br>1. | + | <br>1. The first pin of the MIPI-CSI connector is located in its upper part. |
− | == Display MIPI-DSI interface ( | + | == Display MIPI-DSI interface (FPC/FFC30, 0.5mm) == |
− | [[File: | + | [[File:VisionCB-x2L-STD-DSI.png|center|800px]] |
<center> | <center> | ||
Line 257: | Line 215: | ||
! style="text-align: center; font-weight: bold;" | Pin | ! style="text-align: center; font-weight: bold;" | Pin | ||
! style="text-align: center; font-weight: bold;" | Signal | ! style="text-align: center; font-weight: bold;" | Signal | ||
+ | ! style="text-align: center; font-weight: bold;" | GPIO | ||
! style="text-align: center; font-weight: bold;" | Description | ! style="text-align: center; font-weight: bold;" | Description | ||
|- | |- | ||
| 1 || GND || - | | 1 || GND || - | ||
|- | |- | ||
− | | 2 || DSI-CLK-P || - | + | | 2 || DSI-CLK-P || - || - |
|- | |- | ||
− | | 3 || DSI-CLK-P || - | + | | 3 || DSI-CLK-P || - || - |
|- | |- | ||
− | | 4 || GND || - | + | | 4 || GND || - || - |
|- | |- | ||
− | | 5 || DSI-DATA0-P || - | + | | 5 || DSI-DATA0-P || - || - |
|- | |- | ||
− | | 6 || DSI-DATA0-N || - | + | | 6 || DSI-DATA0-N || - || - |
|- | |- | ||
− | | 7 || GND || - | + | | 7 || GND || - || - |
|- | |- | ||
− | | 8 || DSI-DATA1-P || - | + | | 8 || DSI-DATA1-P || - || - |
|- | |- | ||
− | | 9 || DSI-DATA1-N || - | + | | 9 || DSI-DATA1-N || - || - |
|- | |- | ||
− | | 10 || GND || - | + | | 10 || GND || - || - |
|- | |- | ||
− | | 11 || DSI-DATA2-P || - | + | | 11 || DSI-DATA2-P || - || - |
|- | |- | ||
− | | 12 || DSI-DATA2-N || - | + | | 12 || DSI-DATA2-N || - || - |
|- | |- | ||
− | | 13 || GND || | + | | 13 || GND || - || - |
|- | |- | ||
− | | 14 || DSI-DATA3-P || - | + | | 14 || DSI-DATA3-P || - || - |
|- | |- | ||
− | | 15 || DSI-DATA3-N || - | + | | 15 || DSI-DATA3-N || - || - |
|- | |- | ||
− | | 16 || GND|| - | + | | 16 || GND|| - || - |
|- | |- | ||
− | | 17 || | + | | 17 || I2C1-SCL || RIIC1_SCL || Display confguration I2C interface (3.3V), pull-uped with 2.2k |
|- | |- | ||
− | | 18 || | + | | 18 || I2C1-SDA || RIIC1_SDA || Display confguration I2C interface (3.3V), pull-uped with 2.2k |
|- | |- | ||
− | | 19 || GND || - | + | | 19 || GND || - || - |
|- | |- | ||
− | | 20 || | + | | 20 || DISP-RST || P13-2 || Optional display reset signal |
|- | |- | ||
− | | 21 || | + | | 21 || TP-INT || P17-1 || Optional touch-panel interrupt signal |
|- | |- | ||
− | | 22 || | + | | 22 || TP-RST || P17-2 || Optional touch-panel reset signal |
|- | |- | ||
− | | 23 || GND || - | + | | 23 || GND || - || - |
|- | |- | ||
− | | 24 || +3.3V || Power supply for external devices | + | | 24 || +3.3V || - || Power supply for external devices |
|- | |- | ||
− | | 25 || +3.3V || Power supply for external devices | + | | 25 || +3.3V || - || Power supply for external devices |
|- | |- | ||
− | | 26 || +5V || Power supply for external devices | + | | 26 || +5V || - || Power supply for external devices |
|- | |- | ||
− | | 27 || +5V || Power supply for external devices | + | | 27 || +5V || - || Power supply for external devices |
|- | |- | ||
− | | 28 || | + | | 28 || DSI-BL-PWM || P16-0 || Optional PWM backlight signal |
|- | |- | ||
− | | 29 || | + | | 29 || DSI-BL-EN || P16-1 || Optional ENABLE backlight signal |
|- | |- | ||
− | | 30 || GND || - | + | | 30 || GND || - || - |
|} | |} | ||
</center> | </center> | ||
+ | Note: | ||
+ | <br>1. The first pin of the MIPI-DSI connector is located in its upper part. | ||
− | + | == USB Console Port == | |
− | + | [[File:VisionCB-x2L-STD-console.png|center|800px]] | |
− | |||
− | == USB Console Port | ||
− | [[File: | ||
<center> | <center> | ||
{| class="wikitable" | {| class="wikitable" | ||
− | ! style="text-align: center; font-weight: bold;" | MPU | + | ! style="text-align: center; font-weight: bold;" | Console line |
+ | ! style="text-align: center; font-weight: bold;" | MPU signal | ||
! style="text-align: center; font-weight: bold;" | GPIO | ! style="text-align: center; font-weight: bold;" | GPIO | ||
! style="text-align: center; font-weight: bold;" | Description | ! style="text-align: center; font-weight: bold;" | Description | ||
|- | |- | ||
− | | CONSOLE-TXD || | + | | CONSOLE-TXD || UART0-RXD || P38-1 || GPIO 3.3V voltage levels |
|- | |- | ||
− | | CONSOLE-RXD || | + | | CONSOLE-RXD || UART0-TXD || P38-0 || GPIO 3.3V voltage levels |
|} | |} | ||
</center> | </center> | ||
− | + | == ADC + GPIO connector == | |
− | + | [[File:VisionCB-x2L-STD-ADC.png|center|800px]] | |
− | + | <br> | |
− | + | {| class="wikitable" style="vertical-align:bottom;" | |
− | + | |- style="font-weight:bold; text-align:center;" | |
− | + | ! Pin | |
− | == | + | ! Signal |
− | [[File: | + | ! GPIO |
− | + | ! Description | |
− | |||
− | < | ||
− | {| class="wikitable" | ||
− | |||
− | |||
− | |||
|- | |- | ||
− | | 1 || | + | | 1 |
+ | | GND | ||
+ | | - | ||
+ | | - | ||
|- | |- | ||
− | | 2 || | + | | 2 |
+ | | 3.3V | ||
+ | | - | ||
+ | | - | ||
|- | |- | ||
− | | 3 || | + | | 3 |
+ | | ADC-CH0 | ||
+ | | ADC-CH0 | ||
+ | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | ||
|- | |- | ||
− | | 4 || | + | | 4 |
+ | | ADC-CH1 | ||
+ | | ADC-CH1 | ||
+ | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | ||
|- | |- | ||
− | | 5 || | + | | 5 |
+ | | ADC-CH2 | ||
+ | | ADC-CH2 | ||
+ | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | ||
|- | |- | ||
− | | 6 || | + | | 6 |
+ | | ADC-CH3 | ||
+ | | ADC-CH3 | ||
+ | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | ||
|- | |- | ||
− | | 7 || | + | | 7 |
+ | | ADC-CH4 | ||
+ | | ADC-CH4 | ||
+ | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | ||
|- | |- | ||
− | | 8 || | + | | 8 |
+ | | ADC-CH5 | ||
+ | | ADC-CH5 | ||
+ | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | ||
|- | |- | ||
− | | 9 | + | | 9 |
− | | | + | | ADC-CH6 |
− | + | | ADC-CH6 | |
− | + | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | 10 |
− | + | | ADC-CH7 | |
− | + | | ADC-CH7 | |
− | + | | Dedicated analog input, 12-bit ADC, max. 1.8V on input | |
− | |||
− | |||
− | |||
− | |||
− | | | ||
− | |- | ||
− | | | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | 11 |
+ | | P12-0 | ||
+ | | P12-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 12 |
+ | | P13-1 | ||
+ | | P13-1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 13 |
+ | | P7-2 | ||
+ | | P7-2 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 14 |
+ | | P11-0 | ||
+ | | P11-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 15 |
+ | | P48-2 | ||
+ | | P48-2 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 16 |
+ | | P4-1 | ||
+ | | P4-1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 17 |
+ | | CAN1-RX | ||
+ | | P13-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | + | | 18 | |
− | + | | CAN1-TX | |
− | | 18 | + | | P12-1 |
− | + | | GPIO 3.3V voltage levels | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |- | ||
− | | | ||
− | | | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|} | |} | ||
− | |||
− | |||
− | |||
− | |||
+ | == Raspberry Pi compatible I/O header == | ||
+ | [[File:VisionCB-x2L-STD-GPIO.png|center|800px]] | ||
− | + | {| class="wikitable" | |
− | {| class="wikitable" | + | |- style="font-weight:bold; text-align:center; vertical-align:bottom;" |
− | + | ! Pin | |
− | + | ! Signal | |
− | ! | + | ! MPU signal |
− | ! style=" | + | ! Description |
− | + | |- style="vertical-align:bottom;" | |
− | |||
− | |||
| 1 | | 1 | ||
+ | | 3.3V | ||
+ | | - | ||
| - | | - | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 2 | ||
+ | | 5.0V | ||
| - | | - | ||
| - | | - | ||
|- | |- | ||
− | | | + | | style="vertical-align:bottom;" | 3 |
− | + | | style="vertical-align:bottom;" | I2C0-SDA | |
− | + | | RIIC0_SDA | |
− | | | + | | style="vertical-align:bottom;" | Dedicated I2C MPU line |
− | |- | + | |- style="vertical-align:bottom;" |
− | | | ||
− | | | ||
− | | | ||
− | | | ||
− | |- | ||
| 4 | | 4 | ||
− | | | + | | 5.0V |
− | | | + | | - |
− | + | | - | |
− | |- | ||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
+ | | style="vertical-align:bottom;" | 5 | ||
+ | | style="vertical-align:bottom;" | I2C0-SCL | ||
+ | | RIIC0_SCL | ||
+ | | style="vertical-align:bottom;" | Dedicated I2C MPU line | ||
+ | |- style="vertical-align:bottom;" | ||
| 6 | | 6 | ||
| GND | | GND | ||
+ | | - | ||
+ | | - | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 7 | ||
+ | | P45-0 | ||
+ | | P45-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- | ||
+ | | style="vertical-align:bottom;" | 8 | ||
+ | | style="vertical-align:bottom;" | UART4-TXD | ||
+ | | P2-0 | ||
+ | | style="vertical-align:bottom;" | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 9 | ||
| GND | | GND | ||
+ | | - | ||
| - | | - | ||
|- | |- | ||
− | | | + | | style="vertical-align:bottom;" | 10 |
+ | | style="vertical-align:bottom;" | UART4-RXD | ||
+ | | P2-1 | ||
+ | | style="vertical-align:bottom;" | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 11 | ||
+ | | P8-2 | ||
+ | | P8-2 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 12 | ||
+ | | P15-0 | ||
+ | | P15-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 13 | ||
+ | | P14-1 | ||
+ | | P14-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 14 | ||
+ | | GND | ||
+ | | - | ||
+ | | - | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 15 | ||
+ | | P14-0 | ||
+ | | P14-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 16 | ||
+ | | UART1-RXD | ||
+ | | P40-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 17 | ||
+ | | P11-1 | ||
+ | | P11-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 18 | ||
+ | | UART1-TXD | ||
+ | | P40-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 19 | ||
+ | | SPI0-MOSI | ||
+ | | P43-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 20 | ||
| GND | | GND | ||
+ | | - | ||
+ | | - | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 21 | ||
+ | | SPI0-MISO | ||
+ | | P43-2 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 22 | ||
+ | | P9-1 | ||
+ | | P9-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 23 | ||
+ | | SPI0-CLK | ||
+ | | P43-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 24 | ||
+ | | SPI0-SSL | ||
+ | | P43-3 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 25 | ||
| GND | | GND | ||
| - | | - | ||
+ | | - | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 26 | ||
+ | | P9-0 | ||
+ | | P9-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | 27 |
− | | | + | | I2C3-SDA |
− | | | + | | P46-2 |
− | | | + | | I2C interface used by MPU for SOM PMIC configuration |
− | |||
− | |||
|- | |- | ||
− | | | + | | 28 |
− | | | + | | I2C3-SCL |
+ | | P46-3 | ||
+ | | I2C interface used by MPU for SOM PMIC configuration | ||
+ | |- | ||
+ | | 29 | ||
+ | | UART1-CTS | ||
+ | | P41-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 30 | ||
+ | | GND | ||
| - | | - | ||
− | |||
− | |||
− | |||
− | |||
| - | | - | ||
− | | | + | |- style="vertical-align:bottom;" |
− | |- | + | | 31 |
− | | 3 | + | | UART1-RTS |
− | | | + | | P41-1 |
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 32 | ||
+ | | P1-1 | ||
+ | | P1-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 33 | ||
+ | | P10-1 | ||
+ | | P10-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 34 | ||
+ | | GND | ||
| - | | - | ||
− | |||
− | |||
− | |||
− | |||
| - | | - | ||
− | | | + | |- style="vertical-align:bottom;" |
− | |- | + | | 35 |
− | | | + | | SPI1-MISO |
+ | | P44-2 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 36 | ||
+ | | SPI1-SSL | ||
+ | | P44-3 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 37 | ||
+ | | P10-0 | ||
+ | | P10-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 38 | ||
+ | | SPI1-MOSI | ||
+ | | P44-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | 39 | ||
+ | | GND | ||
| - | | - | ||
| - | | - | ||
− | | | + | |- style="vertical-align:bottom;" |
+ | | 40 | ||
+ | | SPI1-CLK | ||
+ | | P44-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |} | ||
+ | |||
+ | == GMII of ETH0 connection == | ||
+ | [[File:VisionCB-x2L-STD-GMII-ETH0.png|center|800px]] | ||
+ | {| class="wikitable" | ||
+ | |- style="font-weight:bold; text-align:center; vertical-align:bottom;" | ||
+ | ! Signal | ||
+ | ! MPU signal | ||
+ | ! Description | ||
|- | |- | ||
− | | | + | | style="vertical-align:bottom;" | ET0-TXD0 |
+ | | style="vertical-align:bottom;" | ET0-TXD0 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-TXD1 | ||
+ | | ET0-TXD1 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-TXD2 | ||
+ | | ET0-TXD2 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-TXD3 | ||
+ | | ET0-TXD3 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-TXC | ||
+ | | ET0-TXC | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-TX-CTL | ||
+ | | ET0-TX-CTL | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-RXD0 | ||
+ | | ET0-RXD0 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-RXD1 | ||
+ | | ET0-RXD1 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-RXD2 | ||
+ | | ET0-RXD2 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-RXD3 | ||
+ | | ET0-RXD3 | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-RXC | ||
+ | | ET0-RXC | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-RX-CTL | ||
+ | | ET0-RX-CTL | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-MDC | ||
+ | | ET0-MDC | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-MDIO | ||
+ | | ET0-MDIO | ||
+ | | 1.8V Power Domain, GPIO mode not allowed | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-INT | ||
+ | | P47-0 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |- style="vertical-align:bottom;" | ||
+ | | ET0-PHY-RST | ||
+ | | P47-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |} | ||
+ | |||
+ | == GMII of ETH1 connector == | ||
+ | [[File:VisionCB-x2L-STD-GMII.png|center|800px]] | ||
+ | |||
+ | {| class="wikitable" | ||
+ | |- style="font-weight:bold; text-align:center; vertical-align:bottom;" | ||
+ | ! Pin | ||
+ | ! Signal | ||
+ | ! MPU signal | ||
+ | ! Description | ||
+ | |- | ||
+ | | 1 | ||
+ | | 3.3V | ||
| - | | - | ||
| - | | - | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
| 2 | | 2 | ||
− | | | + | | ET1-TXD0 |
− | | | + | | P30-0 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
|- | |- | ||
| 3 | | 3 | ||
− | | | + | | ET1-TXD1 |
− | | | + | | P30-1 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
|- | |- | ||
| 4 | | 4 | ||
− | | | + | | ET1-TXD2 |
− | | | + | | P31-0 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
− | |- | + | |- |
| 5 | | 5 | ||
− | | | + | | ET1-TXD3 |
− | | | + | | P31-1 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
− | |- | + | |- |
| 6 | | 6 | ||
− | | | + | | ET1-TXC |
− | | | + | | P29-0 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
− | |- | + | |- |
| 7 | | 7 | ||
− | | | + | | ET1-TX-CTL |
− | | | + | | P29-1 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
− | |- | + | |- |
| 8 | | 8 | ||
− | | | + | | ET1-RXD3 |
− | | | + | | P36-0 |
− | | | + | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> |
+ | |- | ||
+ | | 9 | ||
+ | | ET1-RXD2 | ||
+ | | P35-1 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 10 | ||
+ | | ET1-RXD1 | ||
+ | | P35-0 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 11 | ||
+ | | ET1-RXD0 | ||
+ | | P34-1 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 12 | ||
+ | | ET1-RX-CTL | ||
+ | | P34-0 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 13 | ||
+ | | ET1-RXC | ||
+ | | P33-1 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 14 | ||
+ | | ET1-MDC | ||
+ | | P37-0 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 15 | ||
+ | | ET1-MDIO | ||
+ | | P37-1 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 16 | ||
+ | | ET1-INT | ||
+ | | P47-2 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
+ | |- | ||
+ | | 17 | ||
+ | | ET1-PHY-RST | ||
+ | | P47-3 | ||
+ | | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.<br /> | ||
|- | |- | ||
− | | | + | | 18 |
− | |- | + | | ET1-VDD-SEL |
− | + | | - | |
− | + | | Ethernet 1 (ET1) interface voltage selection:<br>ET1-VDD-SEL='0' -> V=1.8V;<br>ET1-VDD-SEL='1' or left open -> V=3.3V<br>The line has internal pull-up. | |
− | + | |- | |
− | + | | 19 | |
− | |||
− | | | ||
− | |||
− | |||
− | |||
− | |- | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |- | ||
− | | | ||
| GND | | GND | ||
+ | | - | ||
+ | | - | ||
+ | |- | ||
+ | | 20 | ||
| GND | | GND | ||
| - | | - | ||
− | |- | + | | - |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|} | |} | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | == USB interfaces == | |
− | + | [[File:VisionCB-x2L-STD-USB.png|center|800px]] | |
− | {| class="wikitable" | + | {| class="wikitable" style="vertical-align:bottom;" |
− | + | |- style="font-weight:bold; text-align:center;" | |
− | + | ! Signal | |
− | + | ! MPU signal | |
+ | ! Description | ||
|- | |- | ||
− | | 1 | | + | | USB0-ID |
+ | | P5-1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | USB0-EN |
+ | | P4-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | USB0-OC |
+ | | P5-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | USB1-EN |
+ | | P8-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | USB1-OC |
+ | | P8-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |} | ||
+ | Note: | ||
+ | <br>1. USB0 is configured as host, USB1 channel is configured as USB-OTG. | ||
+ | |||
+ | == Audio codec == | ||
+ | [[File:VisionCB-x2L-STD-audiocodec.png|center|800px]] | ||
+ | {| class="wikitable" style="vertical-align:bottom;" | ||
+ | |- style="font-weight:bold; text-align:center;" | ||
+ | ! Signal | ||
+ | ! MPU signal | ||
+ | ! Description | ||
|- | |- | ||
− | | | + | | SSI-MCLK |
+ | | AUDIO_CLK1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | SSI0-BCK |
+ | | P6-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | SSI0-RCK |
+ | | P6-1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | SSI0-TXD |
+ | | P7-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | SSI0-RXD |
+ | | P7-1 | ||
+ | | GPIO 3.3V voltage levels | ||
+ | |} | ||
+ | Note: | ||
+ | <br>1. Audio codec is configured via I2C2 MPU interface. | ||
+ | |||
+ | == CAN interface == | ||
+ | [[File:VisionCB-x2L-STD-CAN.png|center|800px]] | ||
+ | {| class="wikitable" style="vertical-align:bottom;" | ||
+ | |- style="font-weight:bold; text-align:center;" | ||
+ | ! Signal | ||
+ | ! MPU signal | ||
+ | ! Description | ||
|- | |- | ||
− | | | + | | CAN0-RX |
+ | | P42-2 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | CAN0-TX |
+ | | P42-1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | CAN0-STB |
+ | | P18-1 | ||
+ | | GPIO 3.3V voltage levels (STB line of MCP2542FD) | ||
+ | |} | ||
+ | |||
+ | == RS-485 interface == | ||
+ | [[File:VisionCB-x2L-STD-RS485.png|center|800px]] | ||
+ | {| class="wikitable" style="vertical-align:bottom;" | ||
+ | |- style="font-weight:bold; text-align:center;" | ||
+ | ! Signal | ||
+ | ! MPU signal | ||
+ | ! Description | ||
|- | |- | ||
− | | | + | | UART3-RXD |
+ | | P0-1 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | UART3-TXD |
+ | | P0-0 | ||
+ | | GPIO 3.3V voltage levels | ||
|- | |- | ||
− | | | + | | RS485-RE |
+ | | P18-0 | ||
+ | | GPIO 3.3V voltage levels<br /> In default configuration RS485-RE is connected to nRE and DE inputs of MAX3485 | ||
|- | |- | ||
− | | | + | | RS485-DE |
− | |- | + | | P19-0 |
− | | | + | | GPIO 3.3V voltage levels<br /> In default configuration this line is not used |
− | |||
− | |||
− | |||
− | |||
|} | |} | ||
− | |||
== User Interface (switches and LEDs) == | == User Interface (switches and LEDs) == | ||
− | [[File: | + | [[File:VisionCB-x2L-STD-UI.png|center|800px]] |
− | + | {| class="wikitable" style="vertical-align:bottom;" | |
− | + | |- style="font-weight:bold; text-align:center;" | |
− | + | ! Signal | |
− | + | ! MPU signal | |
− | {| class="wikitable" | + | ! Description |
− | + | |- style="font-weight:bold; text-align:center;" | |
− | ! style=" | + | | colspan="3" | User LEDs |
− | |||
− | | | ||
− | | | ||
− | |||
− | |||
|- | |- | ||
− | | | + | | P45-2 |
− | + | | P45-2 | |
− | + | | Inverted logic level | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | P45-3 |
+ | | P45-3 | ||
+ | | Inverted logic level | ||
|- | |- | ||
− | | | + | | P46-0 |
− | | | + | | P46-0 |
− | + | | Inverted logic level | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | P46-1 |
+ | | P46-1 | ||
+ | | Inverted logic level | ||
|- | |- | ||
− | | | + | | SYS-LED |
+ | | P42-0 | ||
+ | | Inverted logic level | ||
+ | |- style="font-weight:bold; text-align:center;" | ||
+ | | colspan="3" | User switch | ||
|- | |- | ||
− | | | + | | P1-0 |
+ | | P1-0 | ||
+ | | Pushbutton, line pull-uped | ||
|- | |- | ||
− | | | + | | P3-0 |
− | | | + | | P3-0 |
− | + | | Pushbutton, line pull-uped | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | P3-1 |
+ | | P3-1 | ||
+ | | Pushbutton, line pull-uped | ||
|- | |- | ||
− | | | + | | P45-1 |
+ | | P45-1 | ||
+ | | Pushbutton, line pull-uped | ||
|} | |} | ||
− | |||
+ | == RECOVERY jumper == | ||
+ | [[File:VisionCB-x2L-STD-recovery.png|800px|center]] | ||
== Dimensions == | == Dimensions == | ||
− | [[File:VisionCB- | + | [[File:VisionCB-x2L-STD-dimensions.png|800px|center]] |
Latest revision as of 11:14, 4 January 2024
VisionCB-x2L-STD v.1.2 Datasheet and Pinout
Contents
- 1 General description
- 2 Features
- 3 Pictures of VisionCB-x2L-STD v1.2 board
- 4 Ordering info
- 5 Block Diagram
- 6 Electrical parameters
- 7 Power supply connector
- 8 Camera MIPI-CSI interface (FPC/FFC30, 0.5mm)
- 9 Display MIPI-DSI interface (FPC/FFC30, 0.5mm)
- 10 USB Console Port
- 11 ADC + GPIO connector
- 12 Raspberry Pi compatible I/O header
- 13 GMII of ETH0 connection
- 14 GMII of ETH1 connector
- 15 USB interfaces
- 16 Audio codec
- 17 CAN interface
- 18 RS-485 interface
- 19 User Interface (switches and LEDs)
- 20 RECOVERY jumper
- 21 Dimensions
General description
The VisionCB-x2L-STD (with SOM equipped with Renesas RZ/V2L and RZ/G2L MPUs compatible) is a carrier board for the VisionSOM-V2L and VisionSOM-G2L family of computer-on-modules which are powered by dual-core Renesas MPUs (2 x ARM Cortex-A55 + Cortex-M33). The carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as USB, Ethernet, CAN, RS485, audio codec, etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product. The VisionCB-x2L-STD is equipped with a simple user interface consisting of 4 buttons and 4 LEDs. VisionCB-x2L-STD carrier board is also equipped with a large number of popular peripherals, including: RS485, CAN, 10/100/1G Ethernet, MIPI display and camera connectors, serial console port on USB vCOM.
Applications
- Multimedia
- Video streaming
- Image inspection
- VisionAI gateway
- Doorbell systems
- EV chargers
- Smart agriculture gateways
- Industrial embedded Linux computer
- Home Appliances
- Home Automation – Smart Home
- Human-machine Interfaces (HMI)
- Point-of-sales (POS) terminals
- IoT gateways
- Machine vision equipment
- Robotics
- Fitness/outdoor equipment
Features
- Carrier Board compatible with the VisionSOM-G2L and VisionSOM-V2L families of modules based on dual core, heterogenous Renesas RZ/V2L and RZ/G2L application processors
- SoM Connector: SODIMM200
- Expansion Connectors:
- ADC+GPIO connector 2x9 Pin Header (Male)
- Raspberry Pi Compatible Connectors 2x20 Pin Header (Male)
- Ethernet #1 (GMII) Connector Pin Header (Male)
- Communication Connectors:
- 1x Ethernet 10/100/1000Mbit/s (RJ45)
- 1x CAN (1x3 Pin Header, Male)
- 1x RS-485 (1x3 Pin Header, Male)
- 1x USB Host Type A connectors
- 1x USB OTG Micro AB connector
- 1x Console MicroUSB B connector
- Audio Interface:
- Mini-jack 3.5mm (headphones + microphone)
- Display Interface:
- 30-pin FFC/FPC MIPI-DSI (up to 4 lanes)
- Camera Interface:
- 30-pin FFC/FPC MIPI-CSI2 (up to 4 lanes)
- User Interface:
- 4+1 Pushbuttons
- 4+2 LEDs
- External Power Supply 9-12V DC
- Temperature Range: 0 to +70°C
- Board Size: 160mm x 100mm x 21mm
Pictures of VisionCB-x2L-STD v1.2 board
Version | Photo |
---|---|
VisionCB-x2L-STD v1.2 board only | |
VisionCB-x2L-STD v1.2 with VisionSOM-x2L |
Ordering info
Block Diagram
Electrical parameters
Parameter | Value | Units | Comment | ||
---|---|---|---|---|---|
Min. | Typ. | Max. | |||
Power Supply | 9.0 | 12.0 | 15.0 | V | Positive pole on central connector of J200 |
Supply current | - | - | 0.13 | A | Excluding LCD, USB and antoher external loads |
LCD/Camera Power Supply (logic) |
3.25 | 3.3 | 3.35 | V | - |
LCD/Camera Power Supply (backlight and aux) |
4.75 | 4.87 | 4.95 | V | - |
Arduino GPIO voltage | 3.3 | V | - |
Power supply connector
The VisionCB-x2L-STD is equipped with external power source connector with pin diameter 2.5mm and hole diameter 6mm. The voltage of the external power source should be within the range 9-12 VDC.
Camera MIPI-CSI interface (FPC/FFC30, 0.5mm)
Pin | Signal | GPIO | Description |
---|---|---|---|
1 | GND | - | - |
2 | CSI-CLK-P | - | - |
3 | CSI-CLK-P | - | - |
4 | GND | - | - |
5 | CSI-DATA0-P | - | - |
6 | CSI-DATA0-N | - | - |
7 | GND | - | - |
8 | CSI-DATA1-P | - | - |
9 | CSI-DATA1-N | - | - |
10 | GND | - | - |
11 | CSI-DATA2-P | - | - |
12 | CSI-DATA2-N | - | - |
13 | GND | - | - |
14 | CSI-DATA3-P | - | - |
15 | CSI-DATA3-N | - | - |
16 | GND | - | - |
17 | I2C1-SCL | RIIC1_SCL | Camera confguration I2C interface (3.3V), pull-uped with 2.2k |
18 | I2C1-SDA | RIIC1_SDA | Camera confguration I2C interface (3.3V), pull-uped with 2.2k |
19 | GND | - | - |
20 | CSI-GPIO0 | P17-0 | Auxiliary GPIO |
21 | CSI-GPIO1 | P17-1 | Auxiliary GPIO |
22 | - | - | - |
23 | GND | - | - |
24 | +3.3V | - | Power supply for external devices |
25 | +3.3V | - | Power supply for external devices |
26 | +5V | - | Power supply for external devices |
27 | +5V | - | Power supply for external devices |
28 | - | - | - |
29 | - | - | - |
30 | GND | - | - |
Note:
1. The first pin of the MIPI-CSI connector is located in its upper part.
Display MIPI-DSI interface (FPC/FFC30, 0.5mm)
Pin | Signal | GPIO | Description |
---|---|---|---|
1 | GND | - | |
2 | DSI-CLK-P | - | - |
3 | DSI-CLK-P | - | - |
4 | GND | - | - |
5 | DSI-DATA0-P | - | - |
6 | DSI-DATA0-N | - | - |
7 | GND | - | - |
8 | DSI-DATA1-P | - | - |
9 | DSI-DATA1-N | - | - |
10 | GND | - | - |
11 | DSI-DATA2-P | - | - |
12 | DSI-DATA2-N | - | - |
13 | GND | - | - |
14 | DSI-DATA3-P | - | - |
15 | DSI-DATA3-N | - | - |
16 | GND | - | - |
17 | I2C1-SCL | RIIC1_SCL | Display confguration I2C interface (3.3V), pull-uped with 2.2k |
18 | I2C1-SDA | RIIC1_SDA | Display confguration I2C interface (3.3V), pull-uped with 2.2k |
19 | GND | - | - |
20 | DISP-RST | P13-2 | Optional display reset signal |
21 | TP-INT | P17-1 | Optional touch-panel interrupt signal |
22 | TP-RST | P17-2 | Optional touch-panel reset signal |
23 | GND | - | - |
24 | +3.3V | - | Power supply for external devices |
25 | +3.3V | - | Power supply for external devices |
26 | +5V | - | Power supply for external devices |
27 | +5V | - | Power supply for external devices |
28 | DSI-BL-PWM | P16-0 | Optional PWM backlight signal |
29 | DSI-BL-EN | P16-1 | Optional ENABLE backlight signal |
30 | GND | - | - |
Note:
1. The first pin of the MIPI-DSI connector is located in its upper part.
USB Console Port
Console line | MPU signal | GPIO | Description |
---|---|---|---|
CONSOLE-TXD | UART0-RXD | P38-1 | GPIO 3.3V voltage levels |
CONSOLE-RXD | UART0-TXD | P38-0 | GPIO 3.3V voltage levels |
ADC + GPIO connector
Pin | Signal | GPIO | Description |
---|---|---|---|
1 | GND | - | - |
2 | 3.3V | - | - |
3 | ADC-CH0 | ADC-CH0 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
4 | ADC-CH1 | ADC-CH1 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
5 | ADC-CH2 | ADC-CH2 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
6 | ADC-CH3 | ADC-CH3 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
7 | ADC-CH4 | ADC-CH4 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
8 | ADC-CH5 | ADC-CH5 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
9 | ADC-CH6 | ADC-CH6 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
10 | ADC-CH7 | ADC-CH7 | Dedicated analog input, 12-bit ADC, max. 1.8V on input |
11 | P12-0 | P12-0 | GPIO 3.3V voltage levels |
12 | P13-1 | P13-1 | GPIO 3.3V voltage levels |
13 | P7-2 | P7-2 | GPIO 3.3V voltage levels |
14 | P11-0 | P11-0 | GPIO 3.3V voltage levels |
15 | P48-2 | P48-2 | GPIO 3.3V voltage levels |
16 | P4-1 | P4-1 | GPIO 3.3V voltage levels |
17 | CAN1-RX | P13-0 | GPIO 3.3V voltage levels |
18 | CAN1-TX | P12-1 | GPIO 3.3V voltage levels |
Raspberry Pi compatible I/O header
Pin | Signal | MPU signal | Description |
---|---|---|---|
1 | 3.3V | - | - |
2 | 5.0V | - | - |
3 | I2C0-SDA | RIIC0_SDA | Dedicated I2C MPU line |
4 | 5.0V | - | - |
5 | I2C0-SCL | RIIC0_SCL | Dedicated I2C MPU line |
6 | GND | - | - |
7 | P45-0 | P45-0 | GPIO 3.3V voltage levels |
8 | UART4-TXD | P2-0 | GPIO 3.3V voltage levels |
9 | GND | - | - |
10 | UART4-RXD | P2-1 | GPIO 3.3V voltage levels |
11 | P8-2 | P8-2 | GPIO 3.3V voltage levels |
12 | P15-0 | P15-0 | GPIO 3.3V voltage levels |
13 | P14-1 | P14-1 | GPIO 3.3V voltage levels |
14 | GND | - | - |
15 | P14-0 | P14-0 | GPIO 3.3V voltage levels |
16 | UART1-RXD | P40-0 | GPIO 3.3V voltage levels |
17 | P11-1 | P11-1 | GPIO 3.3V voltage levels |
18 | UART1-TXD | P40-1 | GPIO 3.3V voltage levels |
19 | SPI0-MOSI | P43-1 | GPIO 3.3V voltage levels |
20 | GND | - | - |
21 | SPI0-MISO | P43-2 | GPIO 3.3V voltage levels |
22 | P9-1 | P9-1 | GPIO 3.3V voltage levels |
23 | SPI0-CLK | P43-0 | GPIO 3.3V voltage levels |
24 | SPI0-SSL | P43-3 | GPIO 3.3V voltage levels |
25 | GND | - | - |
26 | P9-0 | P9-0 | GPIO 3.3V voltage levels |
27 | I2C3-SDA | P46-2 | I2C interface used by MPU for SOM PMIC configuration |
28 | I2C3-SCL | P46-3 | I2C interface used by MPU for SOM PMIC configuration |
29 | UART1-CTS | P41-0 | GPIO 3.3V voltage levels |
30 | GND | - | - |
31 | UART1-RTS | P41-1 | GPIO 3.3V voltage levels |
32 | P1-1 | P1-1 | GPIO 3.3V voltage levels |
33 | P10-1 | P10-1 | GPIO 3.3V voltage levels |
34 | GND | - | - |
35 | SPI1-MISO | P44-2 | GPIO 3.3V voltage levels |
36 | SPI1-SSL | P44-3 | GPIO 3.3V voltage levels |
37 | P10-0 | P10-0 | GPIO 3.3V voltage levels |
38 | SPI1-MOSI | P44-1 | GPIO 3.3V voltage levels |
39 | GND | - | - |
40 | SPI1-CLK | P44-0 | GPIO 3.3V voltage levels |
GMII of ETH0 connection
Signal | MPU signal | Description |
---|---|---|
ET0-TXD0 | ET0-TXD0 | 1.8V Power Domain, GPIO mode not allowed |
ET0-TXD1 | ET0-TXD1 | 1.8V Power Domain, GPIO mode not allowed |
ET0-TXD2 | ET0-TXD2 | 1.8V Power Domain, GPIO mode not allowed |
ET0-TXD3 | ET0-TXD3 | 1.8V Power Domain, GPIO mode not allowed |
ET0-TXC | ET0-TXC | 1.8V Power Domain, GPIO mode not allowed |
ET0-TX-CTL | ET0-TX-CTL | 1.8V Power Domain, GPIO mode not allowed |
ET0-RXD0 | ET0-RXD0 | 1.8V Power Domain, GPIO mode not allowed |
ET0-RXD1 | ET0-RXD1 | 1.8V Power Domain, GPIO mode not allowed |
ET0-RXD2 | ET0-RXD2 | 1.8V Power Domain, GPIO mode not allowed |
ET0-RXD3 | ET0-RXD3 | 1.8V Power Domain, GPIO mode not allowed |
ET0-RXC | ET0-RXC | 1.8V Power Domain, GPIO mode not allowed |
ET0-RX-CTL | ET0-RX-CTL | 1.8V Power Domain, GPIO mode not allowed |
ET0-MDC | ET0-MDC | 1.8V Power Domain, GPIO mode not allowed |
ET0-MDIO | ET0-MDIO | 1.8V Power Domain, GPIO mode not allowed |
ET0-INT | P47-0 | GPIO 3.3V voltage levels |
ET0-PHY-RST | P47-1 | GPIO 3.3V voltage levels |
GMII of ETH1 connector
Pin | Signal | MPU signal | Description |
---|---|---|---|
1 | 3.3V | - | - |
2 | ET1-TXD0 | P30-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
3 | ET1-TXD1 | P30-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
4 | ET1-TXD2 | P31-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
5 | ET1-TXD3 | P31-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
6 | ET1-TXC | P29-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
7 | ET1-TX-CTL | P29-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
8 | ET1-RXD3 | P36-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
9 | ET1-RXD2 | P35-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
10 | ET1-RXD1 | P35-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
11 | ET1-RXD0 | P34-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
12 | ET1-RX-CTL | P34-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
13 | ET1-RXC | P33-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
14 | ET1-MDC | P37-0 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
15 | ET1-MDIO | P37-1 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
16 | ET1-INT | P47-2 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
17 | ET1-PHY-RST | P47-3 | 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V. |
18 | ET1-VDD-SEL | - | Ethernet 1 (ET1) interface voltage selection: ET1-VDD-SEL='0' -> V=1.8V; ET1-VDD-SEL='1' or left open -> V=3.3V The line has internal pull-up. |
19 | GND | - | - |
20 | GND | - | - |
USB interfaces
Signal | MPU signal | Description |
---|---|---|
USB0-ID | P5-1 | GPIO 3.3V voltage levels |
USB0-EN | P4-0 | GPIO 3.3V voltage levels |
USB0-OC | P5-0 | GPIO 3.3V voltage levels |
USB1-EN | P8-0 | GPIO 3.3V voltage levels |
USB1-OC | P8-1 | GPIO 3.3V voltage levels |
Note:
1. USB0 is configured as host, USB1 channel is configured as USB-OTG.
Audio codec
Signal | MPU signal | Description |
---|---|---|
SSI-MCLK | AUDIO_CLK1 | GPIO 3.3V voltage levels |
SSI0-BCK | P6-0 | GPIO 3.3V voltage levels |
SSI0-RCK | P6-1 | GPIO 3.3V voltage levels |
SSI0-TXD | P7-0 | GPIO 3.3V voltage levels |
SSI0-RXD | P7-1 | GPIO 3.3V voltage levels |
Note:
1. Audio codec is configured via I2C2 MPU interface.
CAN interface
Signal | MPU signal | Description |
---|---|---|
CAN0-RX | P42-2 | GPIO 3.3V voltage levels |
CAN0-TX | P42-1 | GPIO 3.3V voltage levels |
CAN0-STB | P18-1 | GPIO 3.3V voltage levels (STB line of MCP2542FD) |
RS-485 interface
Signal | MPU signal | Description |
---|---|---|
UART3-RXD | P0-1 | GPIO 3.3V voltage levels |
UART3-TXD | P0-0 | GPIO 3.3V voltage levels |
RS485-RE | P18-0 | GPIO 3.3V voltage levels In default configuration RS485-RE is connected to nRE and DE inputs of MAX3485 |
RS485-DE | P19-0 | GPIO 3.3V voltage levels In default configuration this line is not used |
User Interface (switches and LEDs)
Signal | MPU signal | Description |
---|---|---|
User LEDs | ||
P45-2 | P45-2 | Inverted logic level |
P45-3 | P45-3 | Inverted logic level |
P46-0 | P46-0 | Inverted logic level |
P46-1 | P46-1 | Inverted logic level |
SYS-LED | P42-0 | Inverted logic level |
User switch | ||
P1-0 | P1-0 | Pushbutton, line pull-uped |
P3-0 | P3-0 | Pushbutton, line pull-uped |
P3-1 | P3-1 | Pushbutton, line pull-uped |
P45-1 | P45-1 | Pushbutton, line pull-uped |