Personal tools

StarSOM-6ULL Datasheet and Pinout: Difference between revisions

From SomLabs Wiki

Jump to: navigation, search
Created page with "{{PageHeader|StarSOM-6ULL Datasheet and Pinout}} __toc__ __jzpdf__ == General description == 500px|center The StarSOM-6ULL family is a SODIMM-sized..."
 
 
(35 intermediate revisions by 2 users not shown)
Line 2: Line 2:
__jzpdf__
__jzpdf__
== General description ==
== General description ==
[[File:Sl what we do.jpg|500px|center]]
[[File:StarSOM-6ULL-intro.jpg|500px|center]]


The StarSOM-6ULL family is a SODIMM-sized SoM based on the NXP i.MX6 ULL application processor which features an advanced implementation of a single ARM Cortex-A7 core (at speeds up to 900MHz).
The StarSOM-6ULL family is a small size and low profile SoM based on the NXP i.MX6 ULL application processor, which features an advanced implementation of a single ARM Cortex-A7 core (at speeds up to 900MHz).
   
   
The StarSOM-6ULL is a low power highly integrated SoM (System on Module) featuring high computation power and 802.11b/g/n Wi-Fi and Bluetooth v5.1 connectivity. The option of integrated, fully certified Wi-Fi and Bluetooth module simplifies the carrier board design and is ideally suited for wireless application. The StarSOM-6ULL provides a variety memory configuration including flexible range of DDR3L, NAND, eMMC and SD memory card that meets our customers requirements.
The StarSOM-6ULL is a low power highly integrated SoM (System on Module) featuring high computation power, on-board Ethernet PHY 10/100, 802.11b/g/n Wi-Fi and Bluetooth v5.1 connectivity. The option of integrated, fully certified Wi-Fi and Bluetooth module simplifies the carrier board design and is ideally suited for wireless application. The StarSOM-6ULL provides a variety memory configuration including flexible range of DDR3L, and eMMC Flash that meets our customers requirements.


The SoM supports connections to a variety of interfaces: two high-speed USB on-the-go with PHY, dual Ethernet, audio, display with touch panel and serial interfaces. In addition, the system supports industrial grade targeting embedded application.
The SoM supports connections to a variety of interfaces: two high-speed USB on-the-go with PHY, dual Ethernet (single PHY on-board), audio, display with touch panel and serial interfaces. In addition, the system supports industrial grade targeting embedded application.


SOMLabs also provides a complete hardware and software development board for the SoM in the form of a carrier board and optional TFT display and touch panel.  
SOMLabs also provides a complete hardware and software development board for the SoM in the form of a carrier board and optional TFT display and touch panel.  
Line 30: Line 30:
* Powered by NXP i.MX 6ULL application processor
* Powered by NXP i.MX 6ULL application processor
* Core clock up to 900MHz
* Core clock up to 900MHz
* Up to 512MB SDRAM DDR3L
* Up to 1GB RAM DDR3L
* Up to 512MB NAND Flash / 32GB eMMC / uSD memory card
* Up to 32GB eMMC
* Optional Murata 802.11b/g/n Wi-Fi and Bluetooth v5.2 module
* Optional Murata 802.11b/g/n Wi-Fi and Bluetooth v5.1 module
* Power-efficient and cost-optimized solution
* Power-efficient and cost-optimized solution
* Ideal for industrial IoT and embedded applications
* Ideal for industrial IoT and embedded applications
Line 43: Line 43:
|-
|-
| eMMC ||  
| eMMC ||  
[[File:Visionsom-6ull-emmc-top-bottom.jpg|center|thumb]]
[[File:StarSOM-6ull-emmc-top-bottom.jpg|center|thumb]]
|-
| micro-SD ||
[[File:Visionsom-6ull-usd-top-bottom.jpg|center|thumb]]
|-
| NAND Flash ||
[[File:Visionsom-6ull-nand-top-bottom.jpg|center|thumb]]
|}
|}


{| class="frame-green"
{| class="frame-green"
|-
|-
| Wi-Fi is available for all memory variants configurations.
| Wi-Fi and Ethernet PHY10/100 are available as an options.
|}
|}


Line 72: Line 66:
       "name" : "SOM Name",
       "name" : "SOM Name",
       "type" : "selector",
       "type" : "selector",
       "symbol" : "N",
       "symbol" : "0",
       "values" : [
       "values" : [
                     {"value" : "0",
                     {"value" : "0",
                     "description" : "StarSOM"}
                     "description" : "StarSOM board-to-board connectors"}
                 ]
                 ]
     },
     },
Line 90: Line 84:
       "name" : "CPU Type",
       "name" : "CPU Type",
       "type" : "selector",
       "type" : "selector",
       "symbol" : "CpuType",
       "symbol" : "Y2",
       "values" : [
       "values" : [
                     {"value" : "Y2", "description" : "i.MX6 ULL Y2"}
                     {"value" : "Y2", "description" : "i.MX6 ULL Y2"}
                 ]
                 ]
Line 119: Line 112:
       "symbol" : "RamSize",
       "symbol" : "RamSize",
       "values" : [
       "values" : [
                    {"value" : "64R", "description" : "64MB"},
                     {"value" : "128R", "description" : "128MB"},
                     {"value" : "128R", "description" : "128MB"},
                     {"value" : "256R", "description" : "256MB"},
                     {"value" : "256R", "description" : "256MB"},
Line 150: Line 142:
       "values" : [
       "values" : [
                     {"value" : "0SF", "description" : "No Special Features"},
                     {"value" : "0SF", "description" : "No Special Features"},
                     {"value" : "1WB", "description" : "Built-in 802.11b/g/n Wi-Fi and Bluetooth v5.1 Module"}
                     {"value" : "1WB", "description" : "Built-in Murata 802.11b/g/n Wi-Fi and Bluetooth v5.1 Module"},
                    {"value" : "2ET", "description" : "Built-in Microchip 100Mb Ethernet PHY"},
                    {"value" : "3WE", "description" : "Built-in Murata 802.11b/g/n Wi-Fi/Bluetooth v5.1 and Microchip 100Mb Ethernet PHY"}
                 ]
                 ]
     },
     },
Line 165: Line 159:
                     {"value" : "E", "description" : "Extended with Wi-Fi: -25 to +70 C"},
                     {"value" : "E", "description" : "Extended with Wi-Fi: -25 to +70 C"},
                     {"value" : "I", "description" : "Industrial: -40 to +85 C"}
                     {"value" : "I", "description" : "Industrial: -40 to +85 C"}
                ]
    },
    {
        "type" : "separator",
        "value" : "_"
    },
    {
      "name" : "SOM Version",
      "type" : "selector",
      "symbol" : "V",
      "values" : [
                    {"value" : "A", "description" : "Version 1.0"},
                 ]
                 ]
     }
     }
Line 195: Line 177:
|-
|-
| Power Supply
| Power Supply
| <center>5.0</center>
| <center>3.3</center>
| <center>V</center>
| <center>V</center>
| Connected to +5VIN SODIMM pin
| Connected to +3V3IN pins
|-
|-
| Input GPIO voltage
| Input GPIO voltage
Line 229: Line 211:
| Max.
| Max.
|-
|-
| +5VIN
| +3V3IN
| Supply Voltage
| Supply Voltage
| 4.0
| 3.15
| 5.0
| 3.3
| 5.5
| 3.45
| V
| V
|-
|-
| +5VIN
| +3V3IN
| Total Supply Current<sup>1</sup>
| Total Supply Current<sup>1</sup>
| -
| -
| 115
| 175
| 155
| 255
| mA
| mA
|-
|-
Line 250: Line 232:
| V
| V
|-
|-
| +3.3VOUT
| +3V3SW
| SOM Internal LDO<br />Output Current
| Output current of 3.3V power supply for peripherals<br />
| -
| -
| -
| -
| 0.5
| 0.2
| A
| A
|-
|-
Line 283: Line 265:


== SOM pinout ==
== SOM pinout ==
Important notes <br />
StarSOM-6ULL board-to-board connectors view (top view)<br>
1. Detail pin configurations description you can find, edit and arrange in dedicated MEX files (with free "i.MX Pin Tool" configurational tool):
StarrSOM-6ULL connectors type: Hirose DF40C100DP04V51<br>
[https://somlabs.com/wp-content/uploads/SoMLabs-VisionSoM-6ULL-NAND-SD-eMMC-noWIFI.zip VisionSOM-6ULL without WiFi module and no SDIO1 on edge connector] or
[[File:StarSOM-6ULL-connectors.png]]
[https://somlabs.com/wp-content/uploads/SoMLabs-VisionSoM-6ULL-NAND-SD-eMMC-noWIFI-extSDIO1.zip VisionSOM-6ULL without WiFi module and with SDIO1 on edge connector] or
 
[https://somlabs.com/wp-content/uploads/SoMLabs-VisionSoM-6ULL-NAND-SD-eMMC-WiFi.zip VisionSOM-6ULL witht WiFi module on-board]. <br />
2. LCD_DATAxx pins are internally used for boot sequence configuration. We recommend to use LCD_DATAxx lines as outputs or using eFuse boot configuration.


{| class="wikitable"
{| class="wikitable"  
! style="text-align: center; font-weight: bold;" | SODIMM PIN
|-
! style="text-align: center; font-weight: bold;" | Functional
! SoM pin number
domain
! Default  function
! style="text-align: center; font-weight: bold;" | Function name
! GPIO
! style="text-align: center; font-weight: bold;" | i.MX6 UltraLite/
! BGA289 ball
ULL Pad Name
! Notes
! style="text-align: center; font-weight: bold;" | Alternate functions
|-
! Description (refer to i.MX6 UltraLite/ULL manuals for details)
| colspan="5" | <center><b>J101</b></center>
|-
|-
| 1
| 1
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 2
| 2
| Power
| GND
| GND
| -
| -
| -
| -
| -
|-
| 3
| Ctrl
| PMIC-STBY-REQ
| CCM_PMIC_STBY_REQ
| -
| Output, leave open if not used.
|-
| 4
| Ctrl
| MX6-POR-B
| -
| -
| External warm reset input, active L.
|-
| 5
| Ctrl
| PMIC-ON-REQ
| SNVS_PMIC_ON_REQ
| -
| Output, leave open if not used.
|-
| 6
| Power
| VDD-SNVS-3V3
| VDD_SNVS_IN
| -
| SNVS backup power supply must be held between 2.9V and 3.3V if the system requires keeping real time and other data on OFF state. Internally connected to +3.3V, leave open.
|-
| 7
| BOOT
| BOOT-MODE1
| BOOT_MODE1
| GPIO5_IO11
| BOOT-MODE1 BOOT-MODE0
00 boot from fuses (default)
01 serial downloader
10 internal boot
11 reserved
|-
| 8
| Power
| VDD-COIN-3V
| VDD_SNVS_IN
| -
| Optional external coin battery for SNVS power domain, must be held between 2.9V and 3.3V if the system requires keeping real time and other data on OFF state.
Leave open if not used.
|-
| 9
| BOOT
| BOOT-MODE0
| BOOT_MODE0
| GPIO5_IO10
| BOOT-MODE1 BOOT-MODE0
00 boot from fuses (default)
01 serial downloader
10 internal boot
11 reserved
|-
| 10
| GPIO-SNVS
| SNVS-TAMPER9
| SNVS_TAMPER9
| GPIO5_IO09
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 11
| USB
| USB-OTG2-VBUS
| USB_OTG2_VBUS
| -
| +5V USB bus. Leave open if not used.
|-
| 12
| GPIO-SNVS
| SNVS-TAMPER5
| SNVS_TAMPER5
| GPIO5_IO05
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 13
| USB
| USB-OTG1-VBUS
| USB_OTG1_VBUS
| -
| +5V USB bus. Leave open if not used.
|-
| 14
| Ctrl
| ONOFF
| SRC_RESET_B
|  
|  
| Input for power interrupt generation. Leave open if not used.
|-
| 15
| Power
| GND
| -
| -
| -
|-
| 16
| Ctrl
| POR-B
| POR_B
| -
| Cold reset negative logic input resets all modules and logic in the IC.
May be used in addition to internally generated power on reset signal (logical AND, both internal and external signals are considered active low).
|-
| 17
| Power
| GND
| -
| -
| -
|-
| 18
| GPIO-SNVS
| SNVS-TAMPER8
| SNVS_TAMPER8
| GPIO5_IO08
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 19
| USB
| USB-OTG2-DP
| USB_OTG2_DP
| -
| Leave open if not used.
|-
| 20
| Power
| GND
| -
| -
| -
|-
| 21
| USB
| USB-OTG2-DN
| USB_OTG2_DN
| -
| Leave open if not used.
|-
| 22
| Power
| GND
| -
| -
| -
|-
| 23
| Power
| GND
| -
| -
| -
|-
| 24
| GPIO-SNVS
| SNVS-TAMPER7
| SNVS_TAMPER7
| GPIO5_IO07
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 25
| USB
| USB-OTG1-DP
| USB_OTG1_DP
| -
| Leave open if not used.
|-
|-
| 26
| 26
| Power
| LCD.RES
| GND
| GPIO3.04
| -
| E9
| -
|  
| -
|-
| 27
| USB
| USB-OTG1-DN
| USB_OTG1_DN
| -
| Leave open if not used.
|-
|-
| 28
| 28
| Power
| I2C2.SDA
| GND
| GPIO1.31
| -
| G13
| -
| Internally pull-uped with 4.7k connected to 3.3V
| -
|-
| 29
| Power
| GND
| -
| -
| -
|-
|-
| 30
| 30
| GPIO-SNVS
| I2C2.SCL
| SNVS-TAMPER4
| GPIO1.30
| SNVS_TAMPER4
| F17
| GPIO5_IO04
| Internally pull-uped with  4.7k connected to 3.3V
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 31
| USB
| nUSB-OTG-CHD
| USB_OTG1_CHD_B
| -
| Leave open if not used.
|-
|-
| 32
| 32
| GPIO-SNVS
| GPIO1.01
| SNVS-TAMPER1
| GPIO1.01
| SNVS_TAMPER1
| L15
| GPIO5_IO01
|  
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 33
| JTAG
| JTAG-MOD
| JTAG_MOD
| -
| Leave open if not used.
|-
|-
| 34
| 34
| GPIO-SNVS
| GPIO1.02
| SNVS-TAMPER3
| GPIO1.02
| SNVS_TAMPER3
| L14
| GPIO5_IO03
|  
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
| 35
| Power
| GND
| -
| -
| -
|-
|-
| 36
| 36
| GPIO-SNVS
| GPIO1.03
| SNVS-TAMPER0
| GPIO1.03
| SNVS_TAMPER0
| L17
| GPIO5_IO00
|  
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
|-
| 37
| 38
| GPIO1.04
| GPIO1.04
| M16
|  
|  
| CLK1-N
| CCM_CLK1_N
| -
| General purpose differential high speed clock input/output.
Leave open if not used.
|-
|-
| 38
| 39
| Power
| GND
| GND
| -
| -
| -
| -
| -
|-
| 39
|  
|  
| CLK1-P
| CCM_CLK1_P
| -
| General purpose differential high speed clock input/output.
Leave open if not used.
|-
|-
| 40
| 40
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 41
| 41
| Power
| VDD.EMMC
| GND
| -
| -
| -
| -
| -
| Internal 1.8V LDO output as reference or power supply  voltage for QSPI (SDIO) interface
|-
|-
| 42
| 42
| GPIO-SNVS
| LCD.CLK
| SNVS-TAMPER6
| GPIO3.00
| SNVS_TAMPER6
| A8
| GPIO5_IO06
|  
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
|-
| 43
| 43
| JTAG
| QSPI.CLK
| JTAG-TDI
| GPIO4.11
| JTAG_TDI
| D5
| -
| Line referenced to VDD.EMMC power supply (1.8V)
| JTAG TDI input line or GPIO.
|-
|-
| 44
| 44
| GPIO-SNVS
| GND
| SNVS-TAMPER2
| -
| SNVS_TAMPER2
| -
| GPIO5_IO02
|  
| Tamper input (SNVS power domain) or GPIO 3.3V.
|-
|-
| 45
| 45
| GPIO
| QSPI.CS0
| GPIO-8
| GPIO4.16
| GPIO1_IO08
| E6
| PWM1_OUT
| Line referenced to VDD.EMMC  power supply (1.8V)
 
WDOG1_WDOG_B
 
SPDIF_OUT
 
CSI_VSYNC
 
USDHC2_VSELECT
 
CCM_PMIC_RDY
 
UART5_RTS_B
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 46
| 46
| JTAG
| LCD.VSYNC
| JTAG-TMS
| GPIO3.03
| JTAG_TMS
| C9
| -
|  
| JTAG TMS input line or GPIO.
|-
|-
| 47
| 47
| GPIO
| QSPI.D0
| GPIO-4
| GPIO4.12
| GPIO1_IO04
| A3
| ENET1_REF_CLK1
| Line referenced to VDD.EMMC  power supply (1.8V)
 
PWM3_OUT
 
USB_OTG1_PWR
 
USDHC1_RESET_B
 
ENET2_1588_EVENT0_IN
 
UART5_TX
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 48
| 48
| JTAG
| LCD.HSYNC
| JTAG-nTRST
| GPIO3.02
| JTAG_TRST_B
| D9
| -
|  
| JTAG TRST input line (active L) or GPIO.
|-
|-
| 49
| 49
| GPIO
| QSPI.D1
| GPIO-5
| GPIO4.13
| GPIO1_IO05
| C5
| ENET2_REF_CLK2
| Line referenced to VDD.EMMC  power supply (1.8V)
 
PWM4_OUT
 
ANATOP_OTG2_ID
 
CSI_FIELD
 
USDHC1_VSELECT
 
ENET2_1588_EVENT0_OUT
 
UART5_RX
 
| Universal GPIO with 3.3V logic levels.
WLAN-ENABLE in SOM with WiFi/BT module
|-
|-
| 50
| 50
| Power
| LCD.ENABLE
| GND
| GPIO3.01
| -
| B8
| -
|  
| -
|-
|-
| 51
| 51
| Power
| QSPI.D2
| GND
| GPIO4.14
| -
| B5
| -
| Line referenced to VDD.EMMC  power supply (1.8V)
| -
|-
|-
| 52
| 52
| JTAG
| LCD.DATA23
| JTAG-TDO
| GPIO3.28
| JTAG_TDO
| B16
| -
|  
| JTAG TDO output line or GPIO.
|-
|-
| 53
| 53
| GPIO
| QSPI.D3
| GPIO-7
| GPIO4.15
| GPIO1_IO07
| A4
| ENET1_MDC
| Line referenced to VDD.EMMC  power supply (1.8V)
 
ENET2_MDC
 
USB_OTG_HOST_MODE
 
CSI_PIXCLK
 
USDHC2_CD_BCCM_STOP
 
UART1_RTS_B
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 54
| 54
| JTAG
| LCD.DATA22
| JTAG-TCK
| GPIO3.27
| JTAG_TCK
| A14
| -
|  
| JTAG TCK input line or GPIO.
Connected to JTAG-TCK line (via separating resistor 10k).
|-
|-
| 55
| 55
| GPIO
| QSPI.DQS
| GPIO-3
| GPIO4.10
| GPIO1_IO03
| B4
| I2C1_SDA
| Line referenced to VDD.EMMC  power supply (1.8V)
 
GPT1_COMPARE3
 
USB_OTG2_OC
 
USDHC1_CD_B
 
CCM_DI0_EXT_CLK
 
SRC_TESTER_ACK
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 56
| 56
| GPIO
| LCD.DATA21
| GPIO-9
| GPIO3.26
| GPIO1_IO09
| B14
| PWM2_OUT
|  
 
WDOG1_WDOG_ANY
 
SPDIF_IN
 
CSI_HSYNC
 
USDHC2_RESET_B
 
USDHC1_RESET_B
 
UART5_CTS_B
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 57
| 57
| COM-GPIO
| GND
| UART1-TXD
| -
| UART1_TX_DATA
| -
| ENET1_RDATA02
|  
 
I2C3_SCL
 
CSI_DATA02
 
GPT1_COMPARE1
 
GPIO1_IO16
 
SPDIF_OUT
 
UART5_TX
 
| Default: UART1 TxD output or universal GPIO with 3.3V logic levels.
|-
|-
| 58
| 58
| GPIO
| LCD.DATA20
| GPIO-2
| GPIO3.25
| GPIO1_IO02
| C14
| I2C1_SCL
|  
 
GPT1_COMPARE2
 
USB_OTG2_PWR
 
ENET1_REF_CLK_25M
 
USDHC1_WPS
 
DMA_EXT_EVENT00
 
SRC_ANY_PU_RESET
 
UART1_TX
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 59
| 59
| Power
| BT.PCMCLK
| GND
| GPIO4.26
| -
| D3
| -
| BT-BLE interface connection (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| -
|-
|-
| 60
| 60
| Power
| LCD.DATA19
| GND
| GPIO3.24
| -
| D14
| -
|  
| -
|-
|-
| 61
| 61
| GPIO
| BT.PCMOUT
| GPIO-6
| GPIO4.27
| GPIO1_IO06
| D2
| ENET1_MDIO
| BT-BLE interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
ENET2_MDIO
 
USB_OTG_PWR_WAKE
 
CSI_MCLK
 
USDHC2_WPCCM_WAIT
 
CCM_REF_EN_B
 
UART1_CTS_B
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 62
| 62
| GPIO
| LCD.DATA18
| GPIO-1
| GPIO3.23
| GPIO1_IO01
| A13
| I2C2_SDA
|  
 
GPT1_COMPARE1
 
USB_OTG1_OC
 
ENET2_REF_CLK2
 
MQS_LEFT
 
ENET1_1588_EVENT0_OUT
 
SRC_EARLY_RESET
 
WDOG1_WDOG_B
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 63
| 63
| COM-GPIO
| BT.PCMIN
| UART1-RXD
| GPIO4.28
| UART1_RX_DATA
| D1
| ENET1_RDATA03
| BT-BLE interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
I2C3_SDA
 
CSI_DATA03
 
GPT1_CLK
 
GPIO1_IO17
 
SPDIF_IN
 
UART5_RX
 
| Default: UART1 RxD input or universal GPIO with 3.3V logic levels.
|-
|-
| 64
| 64
| GPIO
| LCD.DATA17
| GPIO-0
| GPIO3.22
| GPIO1_IO00
| B13
| I2C2_SCL
|  
 
GPT1_CAPTURE1
 
ANATOP_OTG1_ID
 
ENET1_REF_CLK1
 
MQS_RIGHT
 
ENET1_1588_EVENT0_IN
 
SRC_SYSTEM_RESET
 
WDOG3_WDOG_B
 
| Universal GPIO with 3.3V logic levels.
|-
|-
| 65
| 65
| COM-GPIO
| BT.PCMSYNC
| UART2-TXD
| GPIO4.25
| UART2_TX_DATA
| D4
| ENET1_TDATA02
| BT-BLE interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
I2C4_SCL
 
CSI_DATA06
 
GPT1_CAPTURE1
 
GPIO1_IO20
 
ECSPI3_SS0
 
| Default: UART2 TxD output or universal GPIO with 3.3V logic levels.
|-
|-
| 66
| 66
| COM-GPIO
| LCD.DATA16
| UART1-CTS
| GPIO3.21
| UART1_CTS_B
| C13
| ENET1_RX_CLK
|  
 
USDHC1_WP
 
CSI_DATA04
 
ENET2_1588_EVENT1_IN
 
GPIO1_IO18
 
USDHC2_WP
 
UART5_CTS_B
 
| Default: UART1 CTS output or universal GPIO with 3.3V logic levels.
|-
|-
| 67
| 67
| COM-GPIO
| BT.RTS
| UART2-RXD
| GPIO4.23
| UART2_RX_DATA
| E2
| ENET1_TDATA03
| BT-BLE interface connection  - UART5 (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
I2C4_SDA
 
CSI_DATA07
 
GPT1_CAPTURE2
 
GPIO1_IO21
 
SJC_DONE
 
ECSPI3_SCLK
 
| Default: UART2 RxD input or universal GPIO with 3.3V logic levels.
|-
|-
| 68
| 68
| COM-GPIO
| LCD.DATA15
| UART5-RXD
| GPIO3.20
| UART5_RX_DATA
| D13
| ENET2_COL
|  
 
I2C2_SDA
 
CSI_DATA15
 
CSU_CSU_INT_DEB
 
GPIO1_IO31
 
ECSPI2_MISO
 
EPDC_PWRCTRL03
 
| Default: UART5 RxD input or universal GPIO with 3.3V logic levels.
|-
|-
| 69
| 69
| COM-GPIO
| BT.CTS
| UART3-TXD
| GPIO4.24
| UART3_TX_DATA
| E1
| ENET2_RDATA02
| BT-BLE interface connection  - UART5 (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
CSI_DATA01
 
UART2_CTS_B
 
GPIO1_IO24
 
SJC_JTAG_ACT
 
| Default: UART3 TxD input or universal GPIO with 3.3V logic levels.
|-
|-
| 70
| 70
| Power
| LCD.DATA14
| GND
| GPIO3.19
| -
| A12
| -
|  
| -
|-
|-
| 71
| 71
| Power
| BT.TXD
| GND
| GPIO4.22
| -
| E3
| -
| BT-BLE interface connection  - UART5 (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| -
|-
|-
| 72
| 72
| COM-GPIO
| LCD.DATA13
| UART2-CTS
| GPIO3.18
| UART2_CTS_B
| B12
| ENET1_CRS
|  
 
FLEXCAN2_TXCSI_DATA08
 
GPT1_COMPARE2
 
GPIO1_IO22
 
SJC_DE_B
 
ECSPI3_MOSI
 
| Default: UART2 CTS output or universal GPIO with 3.3V logic levels.
|-
|-
| 73
| 73
| COM-GPIO
| BT.RXD
| UART3-RXD
| GPIO4.21
| UART3_RX_DATA
| E4
| ENET2_RDATA03
| BT-BLE interface connection  - UART5 (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
CSI_DATA00
 
UART2_RTS_B
 
GPIO1_IO25
 
EPIT1_OUT
 
| Default: UART3 RxD input or universal GPIO with 3.3V logic levels.
|-
|-
| 74
| 74
| COM-GPIO
| LCD.DATA12
| UART1-RTS
| GPIO3.17
| UART1_RTS_B
| C12
| ENET1_TX_ER
|  
 
USDHC1_CD_BCSI_DATA05
 
ENET2_1588_EVENT1_OUT
 
GPIO1_IO19
 
USDHC2_CD_B
 
UART5_RTS_B
 
| Default: UART1 RTS input or universal GPIO with 3.3V logic levels.
|-
|-
| 75
| 75
| COM-GPIO
| BT.WAKE
| UART4-TXD
| GPIO4.20
| UART4_TX_DATA
| F3
| ENET2_TDATA02
| BT-BLE interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
I2C1_SCL
 
CSI_DATA12
 
CSU_CSU_ALARM_AUT02
 
GPIO1_IO28
 
ECSPI2_SCLK
 
| Default: UART4 TxD output or universal GPIO with 3.3V logic levels.
|-
|-
| 76
| 76
| COM-GPIO
| LCD.DATA11
| UART3-CTS
| GPIO3.16
| UART3_CTS_B
| D12
| ENET2_RX_CLK
|  
 
FLEXCAN1_TX
 
CSI_DATA10
 
ENET1_1588_EVENT1_IN
 
GPIO1_IO26
 
EPIT2_OUT
 
| Default: UART3 CTS output or universal GPIO with 3.3V logic levels.
|-
|-
| 77
| 77
| COM-GPIO
| BT.HWAKE
| UART4-RXD
| GPIO4.19
| UART4_RX_DATA
| F2
| ENET2_TDATA03
| BT-BLE interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
I2C1_SDA
 
CSI_DATA13
 
CSU_CSU_ALARM_AUT01
 
GPIO1_IO29
 
ECSPI2_SS0
 
EPDC_PWRCTRL01
 
| Default: UART4 RxD input or universal GPIO with 3.3V logic levels.
|-
|-
| 78
| 78
| COM-GPIO
| LCD.DATA10
| UART2-RTS
| GPIO3.15
| UART2_RTS_B
| E12
| ENET1_COL
|  
 
FLEXCAN2_RX
 
CSI_DATA09
 
GPT1_COMPARE3
 
GPIO1_IO23
 
SJC_FAIL
 
ECSPI3_MISO
 
| Default: UART2 RTS input or universal GPIO with 3.3V logic levels.
|-
|-
| 79
| 79
| COM-GPIO
| BT.ENABLE
| UART5-TXD
| GPIO4.17
| UART5_TX_DATA
| F5
| GPIO1_IO30
| BT-BLE interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
ECSPI2_MOSI
 
EPDC_PWRCTRL02
 
ENET2_CRS
 
I2C2_SCL
 
CSI_DATA14
 
CSU_CSU_ALARM_AUT00
 
| Default: UART5 TxD output or universal GPIO with 3.3V logic levels.
|-
|-
| 80
| 80
| COM-GPIO
| LCD.DATA09
| UART3-RTS
| GPIO3.14
| UART3_RTS_B
| A11
| ENET2_TX_ER
|  
 
FLEXCAN1_RX
 
CSI_DATA11
 
ENET1_1588_EVENT1_OUT
 
GPIO1_IO27
 
WDOG1_WDOG_B
 
| Default: UART3 RTS input or universal GPIO with 3.3V logic levels.
|-
|-
| 81
| 81
| Power
| WLAN.HWAKE
| GND
| GPIO4.18
| -
| E5
| -
| WiFi interface connection (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| -
|-
|-
| 82
| 82
| Power
| LCD.DATA08
| GND
| GPIO3.13
| -
| B11
| -
|  
| -
|-
|-
| 83
| 83
| NC
| WLAN.EN
| -
| GPIO1.08
| -
| N17
| -
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| -
|-
|-
| 84
| 84
| Power
| LCD.DATA07
| GND
| GPIO3.12
| -
| D11
| -
|  
| -
|-
|-
| 85
| 85
| Power
| GND
| +3.3VOUT
| -
| -
| -
| -
| +3.3V generated by SOM's LDO.
|  
|-
|-
| 86
| 86
| NC
| LCD.DATA06
| -
| GPIO3.11
| -
| A10
| -
|  
| -
|-
|-
| 87
| 87
| Power
| SDIO1.CLK
| +3.3VOUT
| GPIO2.17
| -
| C1
| -
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| +3.3V generated by SOM's LDO.
|-
|-
| 88
| 88
| Power
| LCD.DATA05
| +3.3VOUT
| GPIO3.10
| -
| B10
| -
|  
| +3.3V generated by SOM's LDO.
|-
|-
| 89
| 89
| Power
| SDIO1.CMD
| +3.3VOUT
| GPIO2.16
| -
| C2
| -
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| +3.3V generated by SOM's LDO.
|-
|-
| 90
| 90
| Power
| LCD.DATA04
| +3.3VOUT
| GPIO3.09
| -
| C10
| -
|  
| +3.3V generated by SOM's LDO.
|-
|-
| 91
| 91
| Power
| SDIO1.D2
| +3.3VOUT
| GPIO2.20
| -
| B1
| -
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| +3.3V generated by SOM's LDO.
|-
|-
| 92
| 92
| Power
| LCD.DATA03
| +3.3VOUT
| GPIO3.08
| -
| D10
| -
|  
| +3.3V generated by SOM's LDO.
|-
|-
| 93
| 93
| Power
| SDIO1.D0
| +3.3VOUT
| GPIO2.18
| -
| B3
| -
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| +3.3V generated by SOM's LDO.
|-
|-
| 94
| 94
| NC
| LCD.DATA02
| -
| GPIO3.07
| -
| E10
| -
|  
| -
|-
|-
| 95
| 95
| NC
| SDIO1.D3
| -
| GPIO2.21
| -
| A2
| -
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
| -
|-
|-
| 96
| 96
| Power
| LCD.DATA01
| +5VIN
| GPIO3.06
| -
| A9
| -
|  
| +4.0-5.5V input power supply.
|-
|-
| 97
| 97
| Ethernet
| SDIO1.D1
| ENET1-RXD0
| GPIO2.19
| ENET1_RX_DATA0
| B2
| UART4_RTS_B
| WiFi interface connection  (if 1DX modules used)<br />    If 1DX modules is not used alternative pin functions (incl. GPIO) available
 
PWM1_OUT
 
CSI_DATA16
 
FLEXCAN1_TX
 
GPIO2_IO00
 
KPP_ROW00
 
USDHC1_LCTL
 
EPDC_SDCE04
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 98
| 98
| Power
| LCD.DATA00
| +5VIN
| GPIO3.05
| -
| B9
| -
|  
| +4.0-5.5V input power supply.
|-
|-
| 99
| 99
| Ethernet
| GND
| ENET1-RXD1
| ENET1_RX_DATA1
| UART4_CTS_B
 
PWM2_OUT
 
CSI_DATA17
 
FLEXCAN1_RX
 
GPIO2_IO01
 
KPP_COL00
 
USDHC2_LCTL
 
EPDC_SDCE05
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
| 100
| Power
| +5VIN
| -
| -
| -
| -
| +4.0-5.5V input power supply.
|-
| 101
| Ethernet
| ENET1-CRS-DV
| ENET1_RX_EN
| UART5_RTS_B
CSI_DATA18
FLEXCAN2_TX
GPIO2_IO02
KPP_ROW01
USDHC1_VSELECT
EPDC_SDCE06
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
| 102
| Power
| +5VIN
|
|  
|  
| +4.0-5.5V input power supply.
|-
|-
| 103
| 100
| Power
| GND
| GND
| -
| -
| -
| -
| -
|-
| 104
| Power
| +5VIN
|  
|  
|
| +4.0-5.5V input power supply.
|-
|-
| 105
| colspan="5" | <center><b>J100</b></center>
| Ethernet
| ENET2-TX-CLK
| ENET2_TX_CLK
| UART8_CTS_B
 
ECSPI4_MISO
 
ENET2_REF_CLK2
 
GPIO2_IO14
 
KPP_ROW07
 
ANATOP_OTG2_ID
 
EPDC_SDDO14
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
10R resistor connected in series.
|-
|-
| 106
| 1
| Power
| +3V3IN
| +5VIN
| -
|  
| -
|  
| External power supply 3.3V
| +4.0-5.5V input power supply.
|-
|-
| 107
| 2
| Power
| +3V3IN
| GND
| -
| -
| -
| External power supply 3.3V
|-
| 3
| +3V3IN
| -
| -
| -
| -
| External power supply 3.3V
|-
|-
| 108
| 4
| Power
| +3V3IN
| +5VIN
| -
|  
| -
|  
| External power supply 3.3V
| +4.0-5.5V input power supply.
|-
|-
| 109
| 5
| Ethernet
| +3V3IN
| ENET2-RXER
| -
| ENET2_RX_ER
| -
| UART8_RTS_B
| External power supply 3.3V
 
ECSPI4_SS0
 
EIM_ADDR25
 
GPIO2_IO15
 
KPP_COL07
 
WDOG1_WDOG_ANY
 
EPDC_SDDO15
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
Connected to WDOG-B line.
|-
|-
| 110
| 6
| Power
| +3V3IN
| +5VIN
| -
| -
| -
| -
| +4.0-5.5V input power supply.
| External  power supply 3.3V
|-
|-
| 111
| 7
| Ethernet
| +3V3IN
| ENET2-RXD0
| -
| ENET2_RX_DATA0
| -
| UART6_TX
| External  power supply 3.3V
 
I2C3_SCL
 
ENET1_MDIO
 
GPIO2_IO08
 
KPP_ROW04
 
USB_OTG1_PWR
 
EPDC_SDDO08
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 112
| 8
| Power
| +3V3IN
| +5VIN
| -
| -
| -
| -
| +4.0-5.5V input power supply.
| External  power supply 3.3V
|-
|-
| 113
| 9
| Ethernet
| +3V3IN
| ENET2-RXD1
| -
| ENET2_RX_DATA1
| -
| UART6_RX
| External  power supply 3.3V
 
I2C3_SDA
 
ENET1_MDC
 
GPIO2_IO09
 
KPP_COL04
 
USB_OTG1_OCE
 
PDC_SDDO09
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 114
| 10
| Ethernet
| +3V3IN
| ENET1-TXEN
| -
| ENET1_TX_EN
| -
| UART6_RTS_B
| External  power supply 3.3V
 
PWM6_OUT
 
CSI_DATA21
 
ENET2_MDC
 
GPIO2_IO05
 
KPP_COL02
 
WDOG2_WDOG_RST_B_DEB
 
EPDC_SDCE09
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 115
| 11
| Power
| GND
| GND
| -
| -
| -
|
|-
| 12
| GND
| -
| -
| -
| -
|
|-
|-
| 116
| 13
| Power
| GND
| GND
| -
| -
| -
|
|-
| 14
| GND
| -
| -
| -
| -
|
|-
|-
| 117
| 15
| Ethernet
| GND
| ENET2-CRS-DV
| -
| ENET2_RX_EN
| -
| UART7_TX
|  
 
I2C4_SCL
 
EIM_ADDR26
 
GPIO2_IO10
 
KPP_ROW05
 
ENET1_REF_CLK_25M
 
EPDC_SDDO10
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 118
| 16
| Ethernet
| ENET1-TX-CLK
| ENET1_TX_CLK
| UART7_CTS_B
 
PWM7_OUT
 
CSI_DATA22
 
ENET1_REF_CLK1
 
GPIO2_IO06
 
KPP_ROW03
 
GPT1_CLK
 
EPDC_SDOED
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
10R resistor connected in series.
|-
| 119
| Ethernet
| ENET2-TXD1
| ENET2_TX_DATA1
| UART8_TX
 
ECSPI4_SCLK
 
EIM_EB_B03
 
GPIO2_IO12
 
KPP_ROW06
 
USB_OTG2_PWR
 
EPDC_SDDO12
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
| 120
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 121
| 17
| Ethernet
| PMIC-ON-REQ
| ENET2-TXEN
|  
| ENET2_TX_EN
|  
| UART8_RX
 
ECSPI4_MOSI
 
EIM_ACLK_FREERUN
 
GPIO2_IO13
 
KPP_COL06
 
USB_OTG2_OC
 
EPDC_SDDO13
 
|  
|  
|-
|-
| 122
| 18
| Ethernet
| ON-OFF
| ENET1-TXD0
| ON-OFF
| ENET1_TX_DATA0
| R8
| UART5_CTS_B
|  
 
CSI_DATA19
 
FLEXCAN2_RX
 
GPIO2_IO03
 
KPP_COL01
 
USDHC2_VSELECT
 
EPDC_SDCE07
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 123
| 19
| Ethernet
| PMIC-STBY-REQ
| ENET2-TXD0
| PMIC-STBY-REQ
| ENET2_TX_DATA0
| U9
| UART7_RX
|  
 
I2C4_SDA
 
EIM_EB_B02
 
GPIO2_IO11
 
KPP_COL05
 
EPDC_SDDO11
 
| Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 124
| 20
| Ethernet
| POR
| ENET1-TXD1
| POR
| ENET1_TX_DATA1
| P8
| UART6_CTS_B
| Power-on-reset input-output
 
PWM5_OUT
 
CSI_DATA20
 
ENET2_MDIO
 
GPIO2_IO04
 
KPP_ROW02
 
WDOG1_WDOG_RST_B_DEB
 
EPDC_SDCE08
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 125
| 21
| Power
| VDD-3V3-SNVS
| GND
| VDD-SNVS-IN
| -
| P12
| -
| SNVS domain power supply<br />    External 3.3V connection power supply is necessary
| -
|-
|-
| 126
| 22
| Ethernet
| RECOVERY
| ENET1-RXER
|  
| ENET1_RX_ER
|  
| UART7_RTS_B
| System recovery pin:<br />    RECOVERY=0 during reset -> start recovery mode<br />    RECOVERY=1 or not connected -> normal operation mode
 
PWM8_OUT
 
CSI_DATA23
 
EIM_CRE
 
GPIO2_IO07
 
KPP_COL03
 
GPT1_CAPTURE2
 
EPDC_SDOEZ
 
| Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 127
| 23
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 128
| 24
| Power
| RESET.IN
| GND
| -
| -
| -
| -
| -
| System reset
|-
|-
| 129
| 25
| LCD
| UART4.RXD
| LCD-DATA21
| GPIO1.29
| LCD_DATA21
| G16
| UART8_RX
| Default Linux console RxD line
 
ECSPI1_SS0
 
CSI_DATA13
 
EIM_DATA13
 
GPIO3_IO26
 
SRC_BT_CFG29
 
USDHC2_DATA1
 
EPDC_SDCE01
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 130
| 26
| Power
| GND
| GND
| -
| -
| -
| -
| -
|
|-
| 27
| UART4.TXD
| GPIO1.28
| G17
| Default Linux console TxD  line
|-
|-
| 131
| 28
| LCD
| TAMPER.0
| LCD-DATA22
| GPIO5.00
| LCD_DATA22
| R10
| MQS_RIGHT
|  
 
ECSPI1_MOSI
 
CSI_DATA14
 
EIM_DATA14
 
GPIO3_IO27
 
SRC_BT_CFG30
 
USDHC2_DATA2
 
USDHC2_DATA2
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 132
| 29
| Power
| +3V3SW
| GND
| -
| -
| -
| -
| -
| Reference 3.3V power supply for external peripherals,  maximum load 200 mA
|-
| 30
| TAMPER.1
| GPIO5.01
| R9
|
|-
|-
| 133
| 32
| LCD
| TAMPER.2
| LCD-DATA17
| GPIO5.02
| LCD_DATA17
| P11
| UART7_RX
|  
 
CSI_DATA00
 
EIM_DATA09
 
GPIO3_IO22
 
SRC_BT_CFG25
 
USDHC2_DATA7
 
EPDC_GDSP
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 134
| 34
| LCD
| TAMPER.3
| LCD-DATA23
| GPIO5.03
| LCD_DATA23
| P10
| MQS_LEFT
|  
 
ECSPI1_MISO
 
CSI_DATA15
 
EIM_DATA15
 
GPIO3_IO28
 
SRC_BT_CFG31
 
USDHC2_DATA3
 
EPDC_SDCE03
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 135
| 36
| Power
| TAMPER.4
| GND
| GPIO5.04
| -
| P9
| -
|  
| -
|-
|-
| 136
| 37
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 137
| 38
| LCD
| TAMPER.5
| LCD-DATA18
| GPIO5.05
| LCD_DATA18
| N8
| PWM5_OUT
|  
 
CA7_MX6ULL_EVENTO
 
CSI_DATA10
 
EIM_DATA10
 
GPIO3_IO23
 
SRC_BT_CFG26
 
USDHC2_CMD
 
EPDC_BDR01
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 138
| 39
| LCD
| USB2.VBUS
| LCD-DATA19
|  
| LCD_DATA19
| U12
| PWM6_OUT
|  
 
WDOG1_WDOG_ANY
 
CSI_DATA11
 
EIM_DATA11
 
GPIO3_IO24
 
SRC_BT_CFG27
 
USDHC2_CLK
 
EPDC_VCOM00
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 139
| 40
| LCD
| TAMPER.6
| LCD-DATA13
| GPIO5.06
| LCD_DATA13
| N11
| SAI3_TX_BCLK
|  
 
CSI_DATA21
 
EIM_DATA05
 
GPIO3_IO18
 
SRC_BT_CFG13
 
USDHC2_RESET_B
 
EPDC_BDR00
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 140
| 41
| LCD
| USB2.DN
| LCD-DATA20
| -
| LCD_DATA20
| T13
| UART8_TX
|  
 
ECSPI1_SCLK
 
CSI_DATA12
 
EIM_DATA12
 
GPIO3_IO25
 
SRC_BT_CFG28
 
USDHC2_DATA0
 
EPDC_VCOM01
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 141
| 42
| LCD
| TAMPER.7
| LCD-DATA14
| GPIO5.07
| LCD_DATA14
| N10
| SAI3_RX_DATA
|  
 
CSI_DATA22
 
EIM_DATA06
 
GPIO3_IO19
 
SRC_BT_CFG14
 
USDHC2_DATA4
 
EPDC_SDSHR
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 142
| 43
| LCD
| USB2.DP
| LCD-DATA15
| -
| LCD_DATA15
| U13
| SAI3_TX_DATA
|  
 
CSI_DATA23
 
EIM_DATA07
 
GPIO3_IO20
 
SRC_BT_CFG15
 
USDHC2_DATA5
 
EPDC_GDRL
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 143
| 44
| LCD
| TAMPER.8
| LCD-DATA8
| GPIO5.08
| LCD_DATA08
| N9
| SPDIF_IN
|  
 
CSI_DATA16
 
EIM_DATA00
 
GPIO3_IO13
 
SRC_BT_CFG08
 
FLEXCAN1_TX
 
EPDC_PWRIRQ
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 144
| 45
| LCD
| LCD-DATA16
| LCD_DATA16
| UART7_TX
 
CSI_DATA01
 
EIM_DATA08
 
GPIO3_IO21
 
SRC_BT_CFG24
 
USDHC2_DATA6
 
EPDC_GDCLK
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
| 145
| LCD
| LCD-DATA9
| LCD_DATA09
| SAI3_MCLK
 
CSI_DATA17
 
EIM_DATA01
 
GPIO3_IO14
 
SRC_BT_CFG09
 
FLEXCAN1_RX
 
EPDC_PWRWAKE
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
| 146
| Power
| GND
| GND
| -
| -
| -
| -
| -
|
|-
| 46
| TAMPER.9
| GPIO5.09
| R6
|
|-
| 47
| GPIO1.05
| GPIO1.05
| M17
|
|-
|-
| 147
| 48
| Power
| GND
| GND
| -
| -
| -
| -
|
|-
| 49
| USB1.VBUS
| -
| -
| T12
|
|-
|-
| 148
| 50
| LCD
| JTAG.TCK
| LCD-DATA11
| GPIO1.14
| LCD_DATA11
| M14
| SAI3_RX_BCLK
| Optionally used as 32kHz clock source for 1DX radio module
 
|-
CSI_DATA19
| 51
 
| USB1.DN
EIM_DATA03
| -
 
| T15
GPIO3_IO16
|  
 
SRC_BT_CFG11
 
FLEXCAN2_RX
 
EPDC_PWRSTAT
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 149
| 52
| LCD
| JTAG.TDI
| LCD-DATA5
| GPIO1.13
| LCD_DATA05
| N16
| UART8_RTS_B
|  
 
ENET2_1588_EVENT2_OUT
 
SPDIF_OUT
 
GPIO3_IO10
 
SRC_BT_CFG05
 
ECSPI1_SS1
 
EPDC_SDDO05
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 150
| 53
| LCD
| USB1.DP
| LCD-DATA12
| -
| LCD_DATA12
| U15
| SAI3_TX_SYNC
|  
 
CSI_DATA20
 
EIM_DATA04
 
GPIO3_IO17
 
SRC_BT_CFG12
 
ECSPI1_RDY
 
EPDC_PWRCTRL00
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 151
| 54
| LCD
| JTAG.TDO
| LCD-DATA6
| GPIO1.12
| LCD_DATA06
| N15
| UART7_CTS_B
|  
 
ENET2_1588_EVENT3_IN
 
SPDIF_LOCK
 
GPIO3_IO11
 
SRC_BT_CFG06
 
ECSPI1_SS2
 
EPDC_SDDO06
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 152
| 55
| LCD
| GND
| LCD-DATA10
| -
| LCD_DATA10
| -
| SAI3_RX_SYNC
|  
 
CSI_DATA18
 
EIM_DATA02
 
GPIO3_IO15
 
SRC_BT_CFG10
 
FLEXCAN2_TX
 
EPDC_PWRCOM
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 153
| 56
| LCD
| JTAG.TMS
| LCD-DATA0
| GPIO1.11
| LCD_DATA00
| P14
| PWM1_OUT
|  
 
ENET1_1588_EVENT2_IN
 
I2C3_SDA
 
GPIO3_IO05
 
SRC_BT_CFG00
 
SAI1_MCLK
 
EPDC_SDDO00
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 154
| 57
| LCD
| USB1.ID
| LCD-DATA3
| GPIO1.00
| LCD_DATA03
| K13
| PWM4_OUT
|  
 
ENET1_1588_EVENT3_OUT
 
I2C4_SCL
 
GPIO3_IO08
 
SRC_BT_CFG03
 
SAI1_RX_DATA
 
EPDC_SDDO03
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 155
| 58
| LCD
| JTAG.TRST
| LCD-DATA1
| GPIO1.15
| LCD_DATA01
| N14
| PWM2_OUT
|  
 
ENET1_1588_EVENT2_OUT
 
I2C3_SCL
 
GPIO3_IO06
 
SRC_BT_CFG01
 
SAI1_TX_SYNC
 
EPDC_SDDO01
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 156
| 60
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 157
| 62
| LCD
| UART1.CTS
| LCD-RESET
| GPIO1.18
| LCD_RESET
| K15
| LCDIF_CS
|  
 
CA7_MX6ULL_EVENT
 
ISAI3_TX_DATA
 
WDOG1_WDOG_ANY
 
GPIO3_IO04
 
ECSPI2_SS3
 
EPDC_GDOE
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 158
| 63
| LCD
| LCD-DATA4
| LCD_DATA04
| UART8_CTS_B
 
ENET2_1588_EVENT2_IN
 
SPDIF_SR_CLK
 
GPIO3_IO09
 
SRC_BT_CFG04
 
SAI1_TX_DATA
 
EPDC_SDDO04
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
| 159
| Power
| GND
| GND
| -
| -
| -
| -
| -
|
|-
| 64
| UART1.RTS
| GPIO1.19
| J14
|
|-
| 65
| ENET2.TX-CLK
| GPIO2.14
| D17
|
|-
| 66
| UART1.RXD
| GPIO1.17
| K16
|
|-
| 67
| ENET2.TXD1
| GPIO2.12
| A16
|
|-
| 68
| UART1.TXD
| GPIO1.16
| K14
|
|-
|-
| 160
| 69
| LCD
| ENET2.TXD0
| LCD-HSYNC
| GPIO2.11
| LCD_HSYNC
| A15
| LCDIF_RS
|  
 
UART4_CTS_B
 
SAI3_TX_BCLK
 
WDOG3_WDOG_RST_B_DEB
 
GPIO3_IO02
 
ECSPI2_SS1
 
EPDC_SDOE
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 161
| 70
| LCD
| UART2.CTS
| LCD-CLK
| GPIO1.22
| LCD_CLK
| J15
| LCDIF_WR_RWN
|  
 
UART4_TX
 
SAI3_MCLK
 
EIM_CS2_B
 
GPIO3_IO00
 
WDOG1_WDOG_RST_B_DEB
 
EPDC_SDCLK
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
10R resistor connected in series.
|-
|-
| 162
| 71
| LCD
| ENET2.TXEN
| LCD-VSYNC
| GPIO2.13
| LCD_VSYNC
| B15
| LCDIF_BUSY
|  
 
UART4_RTS_B
 
SAI3_RX_DATA
 
WDOG2_WDOG_B
 
GPIO3_IO03
 
ECSPI2_SS2
 
EPDC_SDCE00
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 163
| 72
| LCD
| UART2.RTS
| LCD-ENABLE
| GPIO1.23
| LCD_ENABLE
| H14
| LCDIF_RD_E
|  
 
UART4_RX
 
SAI3_TX_SYNC
 
EIM_CS3_B
 
GPIO3_IO01
 
ECSPI2_RDY
 
EPDC_SDLE
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
|-
|-
| 164
| 73
| LCD
| ENET2.RXER
| LCD-DATA2
| GPIO2.15
| LCD_DATA02
| D16
| PWM3_OUT
|  
 
ENET1_1588_EVENT3_IN
 
I2C4_SDA
 
GPIO3_IO07
 
SRC_BT_CFG02
 
SAI1_TX_BCLK
 
EPDC_SDDO02
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 165
| 74
| Power
| UART2.RXD
| GND
| GPIO1.21
| -
| J16
| -
|  
| -
|-
|-
| 166
| 75
| LCD
| ENET2.RXEN
| LCD-DATA7
| GPIO2.10
| LCD_DATA07
| B17
| UART7_RTS_B
|  
 
ENET2_1588_EVENT3_OUT
 
SPDIF_EXT_CLK
 
GPIO3_IO12
 
SRC_BT_CFG07
 
ECSPI1_SS3
 
EPDC_SDDO07
 
| LCD interface signal or universal GPIO with 3.3V logic levels.
Internally used as boot configuration input (Note 2).
|-
|-
| 167
| 76
| SDIO
| UART2.TXD
| SDIO1-D0
| GPIO1.20
| SD1_DATA0
| J17
| GPT2_COMPARE3
|  
 
SAI2_TX_SYNC
 
FLEXCAN1_TX
 
EIM_ADDR21
 
GPIO2_IO18
 
ANATOP_OTG1_ID
 
| SDIO interface signal or universal GPIO with 3.3V logic levels.
 
Used by WiFi/BT module if built-in SOM.
 
Built-in internal pull-up 10k.
 
|-
|-
| 168
| 77
| Power
| ENET2.RXD0
| GND
| GPIO2.08
| -
| C17
| -
|  
| -
|-
|-
| 169
| 78
| SDIO
| UART3.CTS
| SDIO1-D3
| GPIO1.26
| SD1_DATA3
| H15
| GPT2_CAPTURE2
|  
 
SAI2_TX_DATA
 
FLEXCAN2_RX
 
EIM_ADDR24
 
GPIO2_IO21
 
CCM_CLKO2
 
ANATOP_OTG2_ID
 
| SDIO interface signal or universal GPIO with 3.3V logic levels.
 
Used by WiFi/BT module if built-in SOM.
 
Built-in internal pull-up 10k.
 
 
|-
|-
| 170
| 79
| Power
| ENET2.RXD1
| GND
| GPIO2.09
| -
| C16
| -
|  
| -
|-
|-
| 171
| 80
| SDIO
| UART3.RTS
| SDIO1-D1
| GPIO1.27
| SD1_DATA1
| G14
| GPT2_CLK
|  
 
SAI2_TX_BCLK
 
FLEXCAN1_RX
 
EIM_ADDR22
 
GPIO2_IO19
 
USB_OTG2_PWR
 
| SDIO interface signal or universal GPIO with 3.3V logic levels.
 
Used by WiFi/BT module if built-in SOM.
 
Built-in internal pull-up 10k.
 
 
|-
|-
| 172
| 81
| Power
| ENET.MDC
| GND
| GPIO1.07
| -
| L16
| -
|  
| -
|-
|-
| 173
| 82
| SDIO
| UART3.RXD
| SDIO1-CMD
| GPIO1.25
| SD1_CMD
| H16
| GPT2_COMPARE1
|  
 
SAI2_RX_SYNC
 
SPDIF_OUT
 
EIM_ADDR19
 
GPIO2_IO16
 
SDMA_EXT_EVENT00
 
USB_OTG1_PWR
 
| SDIO interface signal or universal GPIO with 3.3V logic levels.
 
Used by WiFi/BT module if built-in SOM.
 
Built-in internal pull-up 10k.
 
 
|-
|-
| 174
| 83
| Power
| ENET.MDIO
| GND
| GPIO1.06
| -
| K17
| -
|  
| -
|-
|-
| 175
| 84
| SDIO
| UART3.TXD
| SDIO1-D2
| GPIO1.24
| SD1_DATA2
| H17
| GPT2_CAPTURE1
|  
 
SAI2_RX_DATA
 
FLEXCAN2_TX
 
EIM_ADDR23
 
GPIO2_IO20
 
CCM_CLKO1
 
USB_OTG2_OC
 
| SDIO interface signal or universal GPIO with 3.3V logic levels.
 
Used by WiFi/BT module if built-in SOM.
 
Built-in internal pull-up 10k.
 
 
|-
|-
| 176
| 85
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 177
| 86
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 178
| 87
| Power
| ENET1.LED0
| GND
| -
| -
| -
| -
| -
| LED0/nWAYEN - output PHY signal (LED cathode)
|-
|-
| 179
| 89
| SDIO
| ENET1.LED1
| SDIO1-CLK
| SD1_CLK
| GPT2_COMPARE2
 
SAI2_MCLK
 
SPDIF_IN
 
EIM_ADDR20
 
GPIO2_IO17
 
USB_OTG1_OC
 
| SDIO interface signal or universal GPIO with 3.3V logic levels.
Used by WiFi/BT module if built-in SOM.
|-
| 180
| Power
| GND
| -
| -
| -
| -
| -
| LED0/SPEED - output PHY  signal (LED cathode)
|-
|-
| 181
| 91
| Power
| ENET1.RXN
| GND
| -
| -
| -
| -
| -
| Rx_n - external Ethernet trafo connector
|-
|-
| 182
| 93
| Power
| ENET1.RXP
| GND
| -
| -
| -
| -
| -
| Rx_p - external Ethernet  trafo connector
|-
|-
| 183
| 95
| CSI
| ENET1.TXN
| CSI-PIXCLK
| CSI_PIXCLK
| USDHC2_WP
 
RAWNAND_CE3_B
 
I2C1_SCL
 
EIM_OE
 
GPIO4_IO18
 
SNVS_HP_VIO_5
 
UART6_RX
 
ESAI_TX2_RX3
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-WAKE in SOM with WiFi/BT module
|-
| 184
| Power
| GND
| -
| -
| -
| -
| -
| Tx_n - external Ethernet  trafo connector
|-
|-
| 185
| 97
| Power
| ENET1.TXP
| GND
| -
| -
| -
| -
| -
| Tx_p - external Ethernet trafo connector
|-
|-
| 186
| 99
| CSI
| CSI-DATA6
| CSI_DATA06
| USDHC2_DATA6
 
ECSPI1_MOSI
 
EIM_AD06
 
GPIO4_IO27
 
SAI1_RX_DATA
 
USDHC1_RESET_BE
 
SAI_TX5_RX0
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-OUT in SOM with WiFi/BT module
|-
| 187
| CSI
| CSI-MCLK
| CSI_MCLK
| USDHC2_CD_B
 
RAWNAND_CE2_B
 
I2C1_SDA
 
EIM_CS0_B
 
GPIO4_IO17
 
SNVS_HP_VIO_5_CTL
 
UART6_TX
 
ESAI_TX3_RX2
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-ENABLE in SOM with WiFi/BT module
|-
| 188
| CSI
| CSI-DATA7
| CSI_DATA07
| USDHC2_DATA7
 
ECSPI1_MISO
 
EIM_AD07
 
GPIO4_IO28
 
SAI1_TX_DATA
 
USDHC1_VSELECT
 
ESAI_TX0
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-IN in SOM with WiFi/BT module
|-
| 189
| Power
| GND
| GND
| -
| -
| -
| -
| -
|  
|-
|-
| 190
| 100
| CSI
| GND
| CSI-DATA5
| CSI_DATA05
| USDHC2_DATA5
 
USDHC2_DATA5
 
EIM_AD05
 
GPIO4_IO26
 
SAI1_TX_BCLK
 
USDHC1_CD_BE
 
SAI_TX_CLK
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-CLK in SOM with WiFi/BT module
|-
| 191
| CSI
| CSI-DATA4
| CSI_DATA04
| USDHC2_DATA4
 
ECSPI1_SCLK
 
EIM_AD04
 
GPIO4_IO25
 
SAI1_TX_SYNC
 
USDHC1_WP
 
ESAI_TX_FS
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-SYNC in SOM with WiFi/BT module
|-
| 192
| CSI
| CSI-DATA3
| CSI_DATA03
| USDHC2_DATA3
 
ECSPI2_MISO
 
EIM_AD03
 
GPIO4_IO24
 
SAI1_RX_BCLK
 
UART5_CTS_B
 
ESAI_RX_CLK
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-CTS in SOM with WiFi/BT module
|-
| 193
| CSI
| CSI-DATA1
| CSI_DATA01
| USDHC2_DATA1
 
ECSPI2_SS0
 
EIM_AD01
 
GPIO4_IO22
 
SAI1_MCLK
 
UART5_RX
 
ESAI_RX_HF_CLK
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-TXD in SOM with WiFi/BT module
|-
| 194
| CSI
| CSI-DATA2
| CSI_DATA02
| USDHC2_DATA2
 
ECSPI2_MOSI
 
EIM_AD02
 
GPIO4_IO23
 
SAI1_RX_SYNC
 
UART5_RTS_B
 
ESAI_RX_FS
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-RTS in SOM with WiFi/BT module
|-
| 195
| CSI
| CSI-DATA0
| CSI_DATA00
| USDHC2_DATA0
 
ECSPI2_SCLK
 
EIM_AD00
 
GPIO4_IO21
 
SRC_INT_BOOT
 
UART5_TX
 
ESAI_TX_HF_CLK
 
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-RXD in SOM with WiFi/BT module
|-
| 196
| Power
| CSI-VREF
| -
| -
| -
| -
| Leave open if not used.
|  
|-
|-
| 197
| CSI
| CSI-HSYNC
| CSI_HSYNC
| USDHC2_CMD
I2C2_SCL
EIM_LBA_B
GPIO4_IO20
PWM8_OUT
UART6_CTS_B
ESAI_TX1
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
WLAN-HWAKE in SOM with WiFi/BT module
|-
| 198
| CSI
| CSI-VSYNC
| CSI_VSYNC
| SDHC2_CLK
I2C2_SDA
EIM_RW
GPIO4_IO19
PWM7_OUT
UART6_RTS_B
ESAI_TX4_RX1
| Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-HWAKE in SOM with WiFi/BT module
|-
| 199
| Power
| GND
| -
| -
| -
| -
| JTAG.MOD
| GPIO1.10
| P15
| Used  as hardware reset Ethernet of PHY with 4.7k pull-down resistor
|-
|-
| 200
| Power
| GND
| -
| -
| -
| BOOT.MODE1
| -
| -
| U10
| Permanently  connected to GND
|}
|}


== Dimensions ==
== Dimensions ==
[[StarSOM-6ULL Dimiensions.png|center]]
[[File:StarSOM-6ULL-dimensions.png|center]]

Latest revision as of 09:20, 13 October 2023

StarSOM-6ULL Datasheet and Pinout

General description

The StarSOM-6ULL family is a small size and low profile SoM based on the NXP i.MX6 ULL application processor, which features an advanced implementation of a single ARM Cortex-A7 core (at speeds up to 900MHz).

The StarSOM-6ULL is a low power highly integrated SoM (System on Module) featuring high computation power, on-board Ethernet PHY 10/100, 802.11b/g/n Wi-Fi and Bluetooth v5.1 connectivity. The option of integrated, fully certified Wi-Fi and Bluetooth module simplifies the carrier board design and is ideally suited for wireless application. The StarSOM-6ULL provides a variety memory configuration including flexible range of DDR3L, and eMMC Flash that meets our customers requirements.

The SoM supports connections to a variety of interfaces: two high-speed USB on-the-go with PHY, dual Ethernet (single PHY on-board), audio, display with touch panel and serial interfaces. In addition, the system supports industrial grade targeting embedded application.

SOMLabs also provides a complete hardware and software development board for the SoM in the form of a carrier board and optional TFT display and touch panel.

Applications

  • Industrial embedded Linux computer
  • Home Appliances
  • Home Automation – Smart Home
  • Human-machine Interfaces (HMI)
  • Point-of-sales (POS) terminals
  • Cash Register
  • 2D barcode scanners and printers
  • Smart grid infrastructure
  • IoT gateways
  • Residential gateways
  • Machine vision equipment
  • Robotics
  • Fitness/outdoor equipment

Features

  • Powered by NXP i.MX 6ULL application processor
  • Core clock up to 900MHz
  • Up to 1GB RAM DDR3L
  • Up to 32GB eMMC
  • Optional Murata 802.11b/g/n Wi-Fi and Bluetooth v5.1 module
  • Power-efficient and cost-optimized solution
  • Ideal for industrial IoT and embedded applications
  • Integrated security features

Pictures of SOM versions

Version Photo
eMMC
Wi-Fi and Ethernet PHY10/100 are available as an options.

Ordering info

SLS06Y2_Clock_RamSize_FlashSize_SF_TEMP
SLSProduct type
SLS - System on Module
0SOM Name
0 - StarSOM board-to-board connectors
6CPU Family
6 - i.MX6
Y2CPU Type
Y2 - i.MX6 ULL Y2
ClockCPU Clock Speed
528C - 528MHz
792C - 792MHz
900C - 900MHz
RamSizeDDR3 RAM Size
128R - 128MB
256R - 256MB
512R - 512MB
FlashSizeFlash Size Type and Density
04GE - 4GB eMMC
08GE - 8GB eMMC
16GE - 16GB eMMC
32GE - 32GB eMMC
SFSpecial Features
0SF - No Special Features
1WB - Built-in Murata 802.11b/g/n Wi-Fi and Bluetooth v5.1 Module
2ET - Built-in Microchip 100Mb Ethernet PHY
3WE - Built-in Murata 802.11b/g/n Wi-Fi/Bluetooth v5.1 and Microchip 100Mb Ethernet PHY
TEMPOperating Temperature
C - Consumer: 0 to +70 C
E - Extended with Wi-Fi: -25 to +70 C
I - Industrial: -40 to +85 C

Block Diagram

Operating ranges

Parameter Value Unit Comment
Power Supply
3.3
V
 Connected to +3V3IN pins
Input GPIO voltage
3.3
V
 -
Environment temperature1
-40…+85
 oC Industrial range w/o WiFi module
-25…+70
 Industrial range with WiFi module
0…+70
 Consumer range

Note:
1. Maximum MPU junction temperature is +105oC (industrial version) or +95oC (consumer version).

Electrical parameters

SOM
signal name 		Parameter Value Units
Min. Typ. Max.
+3V3IN Supply Voltage 3.15 3.3 3.45 V
+3V3IN Total Supply Current1 - 175 255 mA
VGPIO GPIO Input Voltage 0 3.3 3.62 V
+3V3SW Output current of 3.3V power supply for peripherals
 - - 0.2 A
USB-OTGx-VBUS USB Supply 4.40 - 5.5 V
VDD-COIN-3V SNVS Backup
Battery Supply 		2.66 - 3.6 V
- ADC Inputs Voltage 0 - 3.3 V

Notes:
1. Excluding external load connected to +3.3VOUT lines.
2. Applying the maximum voltage 3.6V results in shorten lifetime. Recommended value is smaller than 3.5V.

SOM pinout

StarSOM-6ULL board-to-board connectors view (top view)
StarrSOM-6ULL connectors type: Hirose DF40C100DP04V51


SoM pin number Default function GPIO BGA289 ball Notes
J101
1 GND - -
2 GND - -
26 LCD.RES GPIO3.04 E9
28 I2C2.SDA GPIO1.31 G13 Internally pull-uped with 4.7k connected to 3.3V
30 I2C2.SCL GPIO1.30 F17 Internally pull-uped with 4.7k connected to 3.3V
32 GPIO1.01 GPIO1.01 L15
34 GPIO1.02 GPIO1.02 L14
36 GPIO1.03 GPIO1.03 L17
38 GPIO1.04 GPIO1.04 M16
39 GND - -
40 GND - -
41 VDD.EMMC - - Internal 1.8V LDO output as reference or power supply voltage for QSPI (SDIO) interface
42 LCD.CLK GPIO3.00 A8
43 QSPI.CLK GPIO4.11 D5 Line referenced to VDD.EMMC power supply (1.8V)
44 GND - -
45 QSPI.CS0 GPIO4.16 E6 Line referenced to VDD.EMMC power supply (1.8V)
46 LCD.VSYNC GPIO3.03 C9
47 QSPI.D0 GPIO4.12 A3 Line referenced to VDD.EMMC power supply (1.8V)
48 LCD.HSYNC GPIO3.02 D9
49 QSPI.D1 GPIO4.13 C5 Line referenced to VDD.EMMC power supply (1.8V)
50 LCD.ENABLE GPIO3.01 B8
51 QSPI.D2 GPIO4.14 B5 Line referenced to VDD.EMMC power supply (1.8V)
52 LCD.DATA23 GPIO3.28 B16
53 QSPI.D3 GPIO4.15 A4 Line referenced to VDD.EMMC power supply (1.8V)
54 LCD.DATA22 GPIO3.27 A14
55 QSPI.DQS GPIO4.10 B4 Line referenced to VDD.EMMC power supply (1.8V)
56 LCD.DATA21 GPIO3.26 B14
57 GND - -
58 LCD.DATA20 GPIO3.25 C14
59 BT.PCMCLK GPIO4.26 D3 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
60 LCD.DATA19 GPIO3.24 D14
61 BT.PCMOUT GPIO4.27 D2 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
62 LCD.DATA18 GPIO3.23 A13
63 BT.PCMIN GPIO4.28 D1 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
64 LCD.DATA17 GPIO3.22 B13
65 BT.PCMSYNC GPIO4.25 D4 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
66 LCD.DATA16 GPIO3.21 C13
67 BT.RTS GPIO4.23 E2 BT-BLE interface connection - UART5 (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
68 LCD.DATA15 GPIO3.20 D13
69 BT.CTS GPIO4.24 E1 BT-BLE interface connection - UART5 (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
70 LCD.DATA14 GPIO3.19 A12
71 BT.TXD GPIO4.22 E3 BT-BLE interface connection - UART5 (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
72 LCD.DATA13 GPIO3.18 B12
73 BT.RXD GPIO4.21 E4 BT-BLE interface connection - UART5 (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
74 LCD.DATA12 GPIO3.17 C12
75 BT.WAKE GPIO4.20 F3 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
76 LCD.DATA11 GPIO3.16 D12
77 BT.HWAKE GPIO4.19 F2 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
78 LCD.DATA10 GPIO3.15 E12
79 BT.ENABLE GPIO4.17 F5 BT-BLE interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
80 LCD.DATA09 GPIO3.14 A11
81 WLAN.HWAKE GPIO4.18 E5 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
82 LCD.DATA08 GPIO3.13 B11
83 WLAN.EN GPIO1.08 N17 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
84 LCD.DATA07 GPIO3.12 D11
85 GND - -
86 LCD.DATA06 GPIO3.11 A10
87 SDIO1.CLK GPIO2.17 C1 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
88 LCD.DATA05 GPIO3.10 B10
89 SDIO1.CMD GPIO2.16 C2 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
90 LCD.DATA04 GPIO3.09 C10
91 SDIO1.D2 GPIO2.20 B1 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
92 LCD.DATA03 GPIO3.08 D10
93 SDIO1.D0 GPIO2.18 B3 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
94 LCD.DATA02 GPIO3.07 E10
95 SDIO1.D3 GPIO2.21 A2 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
96 LCD.DATA01 GPIO3.06 A9
97 SDIO1.D1 GPIO2.19 B2 WiFi interface connection (if 1DX modules used)
If 1DX modules is not used alternative pin functions (incl. GPIO) available
98 LCD.DATA00 GPIO3.05 B9
99 GND - -
100 GND - -
J100
1 +3V3IN - - External power supply 3.3V
2 +3V3IN - - External power supply 3.3V
3 +3V3IN - - External power supply 3.3V
4 +3V3IN - - External power supply 3.3V
5 +3V3IN - - External power supply 3.3V
6 +3V3IN - - External power supply 3.3V
7 +3V3IN - - External power supply 3.3V
8 +3V3IN - - External power supply 3.3V
9 +3V3IN - - External power supply 3.3V
10 +3V3IN - - External power supply 3.3V
11 GND - -
12 GND - -
13 GND - -
14 GND - -
15 GND - -
16 GND - -
17 PMIC-ON-REQ
18 ON-OFF ON-OFF R8
19 PMIC-STBY-REQ PMIC-STBY-REQ U9
20 POR POR P8 Power-on-reset input-output
21 VDD-3V3-SNVS VDD-SNVS-IN P12 SNVS domain power supply
External 3.3V connection power supply is necessary
22 RECOVERY System recovery pin:
RECOVERY=0 during reset -> start recovery mode
RECOVERY=1 or not connected -> normal operation mode
23 GND - -
24 RESET.IN - - System reset
25 UART4.RXD GPIO1.29 G16 Default Linux console RxD line
26 GND - -
27 UART4.TXD GPIO1.28 G17 Default Linux console TxD line
28 TAMPER.0 GPIO5.00 R10
29 +3V3SW - - Reference 3.3V power supply for external peripherals, maximum load 200 mA
30 TAMPER.1 GPIO5.01 R9
32 TAMPER.2 GPIO5.02 P11
34 TAMPER.3 GPIO5.03 P10
36 TAMPER.4 GPIO5.04 P9
37 GND - -
38 TAMPER.5 GPIO5.05 N8
39 USB2.VBUS U12
40 TAMPER.6 GPIO5.06 N11
41 USB2.DN - T13
42 TAMPER.7 GPIO5.07 N10
43 USB2.DP - U13
44 TAMPER.8 GPIO5.08 N9
45 GND - -
46 TAMPER.9 GPIO5.09 R6
47 GPIO1.05 GPIO1.05 M17
48 GND - -
49 USB1.VBUS - T12
50 JTAG.TCK GPIO1.14 M14 Optionally used as 32kHz clock source for 1DX radio module
51 USB1.DN - T15
52 JTAG.TDI GPIO1.13 N16
53 USB1.DP - U15
54 JTAG.TDO GPIO1.12 N15
55 GND - -
56 JTAG.TMS GPIO1.11 P14
57 USB1.ID GPIO1.00 K13
58 JTAG.TRST GPIO1.15 N14
60 GND - -
62 UART1.CTS GPIO1.18 K15
63 GND - -
64 UART1.RTS GPIO1.19 J14
65 ENET2.TX-CLK GPIO2.14 D17
66 UART1.RXD GPIO1.17 K16
67 ENET2.TXD1 GPIO2.12 A16
68 UART1.TXD GPIO1.16 K14
69 ENET2.TXD0 GPIO2.11 A15
70 UART2.CTS GPIO1.22 J15
71 ENET2.TXEN GPIO2.13 B15
72 UART2.RTS GPIO1.23 H14
73 ENET2.RXER GPIO2.15 D16
74 UART2.RXD GPIO1.21 J16
75 ENET2.RXEN GPIO2.10 B17
76 UART2.TXD GPIO1.20 J17
77 ENET2.RXD0 GPIO2.08 C17
78 UART3.CTS GPIO1.26 H15
79 ENET2.RXD1 GPIO2.09 C16
80 UART3.RTS GPIO1.27 G14
81 ENET.MDC GPIO1.07 L16
82 UART3.RXD GPIO1.25 H16
83 ENET.MDIO GPIO1.06 K17
84 UART3.TXD GPIO1.24 H17
85 GND - -
86 GND - -
87 ENET1.LED0 - - LED0/nWAYEN - output PHY signal (LED cathode)
89 ENET1.LED1 - - LED0/SPEED - output PHY signal (LED cathode)
91 ENET1.RXN - - Rx_n - external Ethernet trafo connector
93 ENET1.RXP - - Rx_p - external Ethernet trafo connector
95 ENET1.TXN - - Tx_n - external Ethernet trafo connector
97 ENET1.TXP - - Tx_p - external Ethernet trafo connector
99 GND - -
100 GND - -
- JTAG.MOD GPIO1.10 P15 Used as hardware reset Ethernet of PHY with 4.7k pull-down resistor
- BOOT.MODE1 - U10 Permanently connected to GND

Dimensions

Retrieved from "https://wiki.somlabs.com/index.php?title=StarSOM-6ULL_Datasheet_and_Pinout&oldid=3493"