Personal tools

SpaceCB-8Mplus-ADV Datasheet and Pinout: Difference between revisions

From SomLabs Wiki

Jump to: navigation, search
← Older edit
 
(58 intermediate revisions by the same user not shown)
Line 136: Line 136:


== Important information ==
== Important information ==
1. The SpaceCB-8M-ADV carrier board is equippped with dual triple-speed 10/100/1000Mb/s Ethernet interface - RTL812F. Chips are connected to MPU using RGMII interface.
1. The SpaceCB-8M-ADV carrier board is equippped with dual triple-speed 10/100/1000Mb/s Ethernet interface - RTL8211F. Chips are connected to MPU using RGMII interface.
<br>2. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
<br>2. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
<br>3. The I2C2 interface supports on-board audio codec (NAU88C22YG).
<br>3. The I2C2 interface supports on-board audio codec (NAU88C22YG).
<br>4. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).
<br>4. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).
<br>5. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.
<br>5. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.
<br>6. The I2C6 interface supports PI5USB30213A USB-C interface controller.
<br>6. The I2C6 interface supports PI5USB30213A USB-C interface controller. Both I2C6_SDA and I2C6_SCL lines are equipped with pull-up resistors (4.7kOhm) installed on SpaceSOM-8Mplus and not on SpaceCB-8Mplus-ADV.
<br>7. The SPI1 interface supports display controller connected to LVDS1 (J550).
<br>7. The SPI1 interface supports display controller connected to LVDS1 (J550).
<br>8. The SPI2 interface supports display controller connected to LVDS2 (J551).
<br>8. The SPI2 interface supports display controller connected to LVDS2 (J551).
Line 382: Line 382:
<br>2. For configuration purposes is used I2C1 interface.
<br>2. For configuration purposes is used I2C1 interface.
<br>3. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
<br>3. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
<br>4. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).


== LVDS display interfaces (J550 and J551, FPC/FFC 0.5mm) ==
[[File:SpaceCB-8Mplus-ADV-LVDS.png.png|center|700px]]


== Display HDMI interface (J552) ==
[[File:SpaceCB-8Mplus-ADV-HDMI.png|center|700px]]


Note:  
<center>
<br>1. 1st pins of LVDS connectors are located on the left.
{| class="wikitable"
<br>2. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
! style="text-align: center; font-weight: bold;" | J552 pin
<br>3. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | MPU pin
! style="text-align: center; font-weight: bold;" | Description
|-
| 1 || HDMI_TX2_P || AH27  || TMDS_D2_P
|-
| 2 || - || - || GND
|-
| 3 || HDMI_TX2_N || AJ27 || TMDS_D2_N
|-
| 4 || HDMI_TX1_P || AH26 || TMDS_D1_P
|-
| 5 || - || - || GND
|-
| 6 || HDMI_TX1_N || AJ26 || TMDS_D1_N
|-
| 7 || HDMI_TX0_P || AH25 || TMDS_D0_P
|-
| 8 || - || - || GND
|-
| 9 || HDMI_TX0_N || AJ25 || TMDS_D0_N
|-
| 10 || HDMI_TXC_P || AH24 || TMDS_CLK_P
|-
| 11 || - || - || GND
|-
| 12 || HDMI_TXC_N || AJ24 || TMDS_CLK_N
|-
| 13 || HDMI_CEC || AD22 || CEC
|-
| 14 || EARC_P_UTIL || AJ23 || AUX_P
|-
| 15 || HDMI_DDC_SCL || AC22 ||DDC_CLK
|-
| 16 || HDMI_DDC_SDA || AF22 || DDC_DAT
|-
| 17 || - || - || GND
|-
| 18 || - || - || +5V
|-
| 19 || EARC_N_HPD || AH22 || HPD/AUX_N
|}
</center>


== USB and USB-OTG interfaces ==
== LVDS display interfaces (J550 and J551, FPC/FFC 0.5mm) ==
[[File:visionCB-8Mmini-ADV-USB.png|center|700px]]
[[File:SpaceCB-8Mplus-ADV-LVDS.png.png|center|700px]]
The VisionCB-8M-ADV is equipped with 2 channel of USB:
<br>- USB-OTG (connector J501, microUSB) - connected to MPU's USB1 channel,
<br>- host USB 2.0 (connector J501, USB-A) - connected to MPU's USB2 channel.
<br>In both channels external USB devices are powered with power switch equipped with monitored outputs. In the event of a short circuit the LED-OC lights-up signalling overcurrent.
 
== USB Console Port and Segger J-Link debugger ==
[[File:visionCB-8Mmini-ADV-JLINK.png|center|700px]]


<center><b>Pin description of J550 (LVDS1)</b></center>
<center>
<center>
{| class="wikitable"
{| class="wikitable"
! style="text-align: center; font-weight: bold;" | MPU Port
! style="text-align: center; font-weight: bold;" | J550 pin
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | MPU pin
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| CONSOLE-TXD || UART4-TXD || Signal connected to J304 pin 2
| 1 || GND || - || -  
|-
| 2 || LVDS1.DATA0_N || - || -
|-
| 3 || LVDS1.DATA0_P || - || -
|-
| 4 || GND || - || -
|-
| 5 || LVDS1.DATA1_N || - || -
|-
| 6 || LVDS1.DATA1_P || - || -
|-
| 7 || GND || - || -
|-
| 8 || LVDS1.DATA2_N || - || -
|-
| 9 || LVDS1.DATA2_P || - || -
|-
| 10 || GND || - || -
|-
| 11 || LVDS1.CLK_N || - || -
|-
| 12 || LVDS1.CLK_P || - || -
|-
| 13 || GND || - ||
|-
| 14 || LVDS1.DATA3_N || - || -
|-
| 15 || LVDS1.DATA3_P || - || -
|-
| 16 || ECSPI1_MOSI || AC20 || Backlight on/off
|-
| 17 || ECSPI1_MISO || AD20 || Backlight brightness control (PWM)
|-
| 18 || ECSPI1_CS0 || AE20 || For optional use
|-
|-
| CONSOLE-RXD || UART4-RXD || Signal connected to J304 pin 3
| 19 || I2C4.SCL || AF8 || Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 20 || I2C4.SDA || AD8 || Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 21 || +5V || - || Power supply for external devices
|-
| 22 || +5V || - || Power supply for external devices
|}
|}
</center>
</center>


Notes:
<center><b>Pin description of J551 (LVDS2)</b></center>
<br>1. Linux console port (UART4 in MPU) uses vCOM interface provided by built-in debugger Segger J-Link.
<br>2. vCOM can be disconnected from MPU with JP801 (jumper CON in position ON or OFF).
<br>3. Lines TXD and RXD of UART4 are easy to monitoring thanks to using J304 gold-pins.
<br>4. Debug JTAG interface can be disconnected from MPU with JP801 (jumper J-LINK in position ON or OFF).
<br>5. J-Link activity is monitored with ACT LED.
 
== MicroSD card interface (J308) ==
[[File:visionCB-8Mmini-ADV-SDcard.png|center|700px]]
 
 
<center>
<center>
{| class="wikitable"
{| class="wikitable"
! style="text-align: center; font-weight: bold;" | Card connector pin
! style="text-align: center; font-weight: bold;" | J551 pin
! style="text-align: center; font-weight: bold;" | SD card signal
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | MPU pin
! style="text-align: center; font-weight: bold;" | Description
|-
| 1 || GND || -  || -
|-
| 2 || LVDS2.DATA0_N || - || -
|-
| 3 || LVDS2.DATA0_P || - || -
|-
|-
| 1 || DATA2 || SD1-DATA2
| 4 || GND || - || -
|-
|-
| 2 || DATA3 || SD1-DATA3
| 5 || LVDS2.DATA1_N || - || -
|-
|-
| 3 || CMD || SD1-CMD
| 6 || LVDS2.DATA1_P || - || -
|-
|-
| 4 || NVCC-SDIO || Voltage selected 1.8/3.3V by SD1 driver
| 7 || GND || - || -
|-
|-
| 5 || CLK || SD1-CLK
| 8 || LVDS2.DATA2_N || - || -
|-
|-
| 6 || GND || -
| 9 || LVDS2.DATA2_P || - || -
|-
|-
| 7 || DATA0 || SD1-DATA0
| 10 || GND || - || -
|-
|-
| 8 || DATA1 || SD1-DATA1
| 11 || LVDS2.CLK_N || - || -
|-
|-
| 9 || CARD-DETECT || SD1-CD
| 12 || LVDS2.CLK_P || - || -
|-
| 13 || GND || - ||
|-
| 14 || LVDS2.DATA3_N || - || -
|-
| 15 || LVDS2.DATA3_P || - || -
|-
| 16 || ECSPI2_CS0 || AJ22 || Backlight on/off
|-
| 17 || ECSPI2_MOSI || AJ21 || Backlight brightness control (PWM)
|-
| 18 || ECSPI2_MISO || AH20 || For optional use
|-
| 19 || I2C1.SCL || AC8 || Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 20 || I2C1.SDA || AH7 || Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 21 || +5V || - || Power supply for external devices
|-
| 22 || +5V || - || Power supply for external devices
|}
|}
</center>
</center>


== 24-bit stereo audio codec ==
 
[[File:visionCB-8Mmini-ADV-CODEC.png|center|700px]]
Note:  
<br>1. 1st pins of LVDS connectors are located on the left.
<br>2. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
<br>3. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.




The VisionCB-8M-ADV board is equipped with 24-bit stereo codec - Nuvoton NAU88C22YG - with integrated audio amplifier.
== MicroSD card connector (J701) ==
<br>The NAU88C22 is a low power, high quality CODEC for portable and general purpose audio applications. In addition to precision 24-bit stereo ADCs and DACs, NAU88C22YG integrates a broad range of additional functions to simplify implementation of complete audio system solutions. The NAU88C22 includes drivers for speaker, headphone, and differential or stereo line outputs, and integrates preamps for stereo differential microphones,significantly reducing external component requirements.
[[File:SpaceCB-8Mplus-ADV-uSD.png|center|700px]]
<br>Connector marked Spk can be used as stereo (Left-GND/Right-GND) or mono bridge output (speaker connected to L-R pins).


<center>
<center>
{| class="wikitable"
{| class="wikitable"
! style="text-align: center; font-weight: bold;" | J701 pin
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | MPU pin
! style="text-align: center; font-weight: bold;" | MPU pin
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| SAI3-MCLK || AD6 || Codec master clock
| 1 || SD1_DATA2 || V29  || DATA2
|-
|-
| SAI3-TXC || AG6 || Codec BCLK line
| 2 || SD1_DATA3 || V28 || DATA3
|-
|-
| SAI3-TXFS || AC6 || Codec FS line
| 3 || SD1_SMD || W29 || CMD
|-
|-
| SAI3-TXD || AF6 || Codec input line
| 4 || 1.8/3.3V || - || VDD (uSD power supply)<br>selected internally with SAI5_RXD0
|-
|-
| SAI3-RXD || AF7 || Codec output line
| 5 || SD1_CLK || W28 || CLK
|-
|-
| I2C1-SCL || E9 || Confguration I2C interface with 4.7kOhm pull-up (3.3V)
| 6 || - || - || GND
|-
|-
| I2C1-SDA || F9 || UConfguration I2C interface with 4.7kOhm pull-up (3.3V)
| 7 || SD1_DATA0 || Y29 || DATA0
|-
| 8 || SD1_DATA1 || Y28 || DATA1
|-
| SW || SD1_RESET_B || W25 || Card Detect
|}
|}
</center>
</center>


Note:
Note:
<br>1. The I2C1 interface is common to MIPI-CSI interface and audio codec.
<br>1. Value of VDD for uSD is selected with SAI5_RXD0 (MPU) pin.
 
== USB-C interface ==
[[File:SpaceCB-8Mplus-ADV-USBC.png|center|700px]]
 
Note:
<br>1. USB-C interface built-in SpaceCB-8Mplus-ADV is connected to USB1 channel.
<br>2. The I2C6 interface supports configuration of PI5USB30213A USB-C controller.


== On-board RTC ==
== USB 3.0 interface ==
[[File:visionCB-8Mmini-ADV-RTC.png|center|700px]]
[[File:SpaceCB-8Mplus-ADV-USB3.png|center|700px]]


The VisionCB-8M-ADV is equipped with on-board RTC module based on NXP PCF85263AT.
USB 3.0 interface built-in SpaceCB-8Mplus-ADV is connected to USB2 channel.
<br>The PCF85263A is a CMOS1 Real-Time Clock (RTC) and calendar optimized for low power consumption and with automatic switching to battery on main power loss.  
 
<br>The RTC can also be configured as a stop-watch (elapsed time counter). Three time log registers triggered from battery switch-over as well as input driven events.  
== USB Console Port and Segger J-Link debugger ==
<br>Featuring clock output and two independent interrupt signals, two alarms, I2C interface and quartz crystal calibration.
[[File:SpaceCB-8Mplus-ADV-CONSOLE.png|center|700px]]
<br>RTC can be powered by an external CR1220 battery (socket J302).
 
<center>
{| class="wikitable"
! style="text-align: center; font-weight: bold;" | MPU Port
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | Description
|-
| CONSOLE-TXD || UART4-TXD || TXD line of console port
|-
| CONSOLE-RXD || UART4-RXD || RXD line of console port
|}
</center>
 
Notes:
<br>1. Linux console port (UART4 in MPU) uses vCOM interface provided by built-in debugger Segger J-Link.
<br>2. vCOM can be disconnected from MPU with jumper CON (position ON or OFF).
<br>3. Debug JTAG interface can be disconnected from MPU with jumper J-LINK (position ON or OFF).
<br>4. J-Link activity is monitored with ACT LED.
 
== 24-bit stereo audio codec ==
[[File:SpaceCB-8Mplus-ADV-CODEC.png|center|700px]]
 
 
The SpaceCB-8M-ADV board is equipped with 24-bit stereo codec - Nuvoton NAU88C22YG - with integrated audio amplifier.
<br>The NAU88C22 is a low power, high quality CODEC for portable and general purpose audio applications. In addition to precision 24-bit stereo ADCs and DACs, NAU88C22YG integrates a broad range of additional functions to simplify implementation of complete audio system solutions. The NAU88C22 includes drivers for speaker, headphone, and differential or stereo line outputs, and integrates preamps for stereo differential microphones,significantly reducing external component requirements.


<center>
<center>
Line 499: Line 632:
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| I2C2-SCL || D10 || Communication I2C interface with 4.7kOhm pull-up (3.3V)
| SAI3_MCLK || AJ20 || Codec master clock
|-
| SAI3_TXC || AH19 || Codec BCLK line
|-
| SAI3_TXFS || AC16 || Codec FS line
|-
| SAI3_TXD || AH18 || Codec input line
|-
| SAI3_RXD || AF18 || Codec output line
|-
|-
| I2C2-SDA || D9 || Communication I2C interface with 4.7kOhm pull-up (3.3V)
| I2C2_SCL || AH6 || Confguration I2C interface with 4.7kOhm pull-up (3.3V)
|-
|-
| GPIO4-IO15 || AC6 || RTC interrupt line with 4.7kOhm pull-up (3.3V)
| I2C1_SDA || AE8 || Confguration I2C interface with 4.7kOhm pull-up (3.3V)
|}
|}
</center>
</center>


Notes:<br />
== Dual CAN-FD serial interface ==
<br>1. The I2C2 interface is common to onboard RTC, HDMI-DDC, LT8912B bridge configuration and MIPI-DSI display controller.
[[File:SpaceCB-8Mplus-ADV-CANFD.png|center|700px]]
 
== CAN FD serial interface ==
[[File:visionCB-8Mmini-ADV-CAN.png|center|700px]]




The VisionCB-8M-ADV board is equipped with Microchip CAN FD controller (MCP2518FDT-E/SL) with physical layer interface (MCP2542FD-E/SN).
The SpaceCB-8Mplus-ADV board is equipped with Microchip CAN-FD with physical layer interfaces MCP2542FD-E/SN, connected to internal CAN1 and CAN2 channels.
<br>The MCP2518FD supports both CAN frames in the Classical format (CAN 2.0B) and CAN Flexible Data Rate (CAN FD) format as specified in ISO11898-1:2015.
<br>The MCP2518FD is connected to default SPI2 channel and pins.


<center>
<center>
Line 522: Line 658:
! style="text-align: center; font-weight: bold;" | Signal
! style="text-align: center; font-weight: bold;" | Signal
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | Default MPU pin name
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | MPU pin
|-
|-
| SDO || SPI2-MISO || SPI2 MISO (MCP2518FDT output)
| CAN1.TX || SPDIF_TX || AE18
|-
|-
| SDI || SPI2-MOSI || SPI2 MOSI (MCP2518FDT input)
| CAN1.RX || SPDIF_RX || AD18
|-
|-
| SCK || SPI2-SCK || SPI2 clock
| CAN2.TX || SAI2_RXC || AH16
|-
|-
| CS# || SPI2-SS0 || Select MCP2518FDT device
| CAN2.RX || SAI2_MCLK || AJ15
|-
| INT# || GPIO4-IO16 || Interrupt from MCP2518FDT
|}
|}
</center>
</center>


== RS-485 simplex serial interface ==
== RS-485 semiduplex serial interface ==
[[File:visionCB-8Mmini-ADV-RS485.png|center|700px]]
[[File:SpaceCB-8Mplus-ADV-RS485.png|center|700px]]




The VisionCB-8M-ADV board is equipped with low-voltage RS-485 physical layer interface MAX3485.
The SpaceCB-8Mplus-ADV board is equipped with low-voltage RS-485 physical layer interface MAX3485.
<br>The RS-485 is connected to default UART3 (TxD, RxD) channel and pins. Transmission control lines (RE# and DE) are controlled by MPU hardware.
<br>The RS-485 is connected to default UART2 (TxD, RxD) channel and pins. Transmission control line DE is controlled by MPU GPIO.


<center>
<center>
Line 549: Line 683:
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| RO || UART3-RXD || Data received by MPU
| RO || UART2_RXD || Data received by MPU
|-
|-
| DI || UART3-TXD || Data transmitted by MPU
| DI || UART2_TXD || Data transmitted by MPU
|-
|-
| RE#/DE || SPI1-MISO || Receiver Enable (active low)/Transmitter Enable (active high) signal<br>This signal is also connected to J303 (SERIAL COMM connector)
| DE || GPIO5.05 || Transmitter Enable (active high) signal
|}
|}
</center>
</center>


== Serial Communication/GPIO header (J303) ==
Note:
[[File:visionCB-8Mmini-ADV-serialComm.png|center|700px]]
<br>1. nRE line of MAX3485 is permanently connected to GND.
 
== GPIO header (J702) ==
[[File:SpaceCB-8Mplus-ADV-GPIO.png|center|700px]]


Pin numeration, 1st pin of J303 connector SERIAL COMM is marked with arrow (on picture above).<br>
[[File:IDC_2x8.png|center|400px]]
<br>
<br>
<center>
<center>
{| class="wikitable"
{| class="wikitable"
! style="text-align: center; font-weight: bold;" | Pin
! style="text-align: center; font-weight: bold;" | J702 pin
! style="text-align: center; font-weight: bold;" | Default pin name
! style="text-align: center; font-weight: bold;" | Default pin name
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| 1 || GND || -
| 1 || - || +3.3V
|-
| 2 || - || +5V
|-
| 3 || I2C1_SDA || I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 4 || - || +5V
|-
| 5 || I2C1_SCL || I2C interface with 4.7kOhm pull-up (3.3V)
|-
|-
| 2 || GND || -
| 6 || - || GND
|-
|-
| 3 || I2C3-SDA || By default: I2C interface with 4.7kOhm pull-up (3.3V)
| 7 || GPIO1.04 || -
|-
|-
| 4 || UART2-TXD || By default: UART2-TXD or universal GPIO with 3.3V logic levels
| 8 || UART3_TXD || -
|-
|-
| 5 || I2C3-SCL || By default: I2C interface with 4.7kOhm pull-up (3.3V)
| 9 || - || GND
|-
|-
| 6 || UART2-RXD || By default: UART2-RXD or universal GPIO with 3.3V logic levels
| 10 || UART3_RXD || -
|-
|-
| 7 || SPI1-SS0 || By default: SPI1-SS0 or universal GPIO with 3.3V logic levels
| 11 || GPIO1.05 || -
|-
|-
| 8 || GPIO4-IO28 || By default: GPIO4-IO28 or universal GPIO with 3.3V logic levels<br>Optionally can be used in LVDS channel
| 12 || I2C3_SCL || I2C interface with 4.7kOhm pull-up (3.3V)
|-
|-
| 9 || SPI1-MOSI || By default: SPI1-MOSI or universal GPIO with 3.3V logic levels
| 13 || GPIO1_06 || -
|-
|-
| 10 || GPIO4-IO29 || By default: GPIO4-IO29 or universal GPIO with 3.3V logic levels<br>Optionally can be used in LVDS channel
| 14 || - || GND
|-
|-
| 11 || SPI1-MISO || By default: SPI1-MISO or universal GPIO with 3.3V logic levels<br>This signal is used as RE#/DE signal in RS-485 communication channel
| 15 || GPIO1_07 || -
|-
|-
| 12 || GPIO4-IO18 || By default: GPIO4-IO18 or universal GPIO with 3.3V logic levels
| 16 || NC || Not connected
|-
|-
| 13 || SPI1-CLK || By default: SPI1-CLK or universal GPIO with 3.3V logic levels
| 17 || - || +3.3V
|-
|-
| 14 || GPIO4-IO19 || By default: GPIO4-IO19 or universal GPIO with 3.3V logic levels
| 18 || NC || Not connected
|-
|-
| 15 || +3.3V || +3.3V generated by DC/DC built-in SOM (limited current load)
| 19 || ECSPI2_MOSI || -
|-
|-
| 16 || GPIO4-IO17 || By default: GPIO4-IO17 or universal GPIO with 3.3V logic levels
| 20 || - || GND
|-
| 21 || ECSPI2_MISO || -
|-
| 22 || GPIO1_08 || -
|-
| 23 || ECSPI2_SCLK || -
|-
| 24 || ECSPI2_CS0 || -
|-
| 25 || - || GND
|-
| 26 || GPIO1_09 || -
|-
| 27 || I2C4_SDA || I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 28 || I2C4_SCL || I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 29 || NC || Not connected
|-
| 30 || - || GND
|-
| 31 || NC || Not connected
|-
| 32 || GPIO1_10 || -
|-
| 33 || I2C3_SDA || I2C interface with 4.7kOhm pull-up (3.3V)
|-
| 34 || - || GND
|-
| 35 || ECSPI1_MISO || -
|-
| 36 || GPIO1_11 || -
|-
| 37 || ECSPI1_CS0 || -
|-
| 38 || ECSPI1_MOSI || -
|-
| 39 || - || GND
|-
| 40 || ECSPI1_SCLK || -
|}
|}
</center>
</center>


Note:
Note:
<br>1. 1st pin of J303 connector SERIAL COMM is marked with arrow.
<br>1. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
<br>2. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).
<br>3. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.


== User Interface (switches and LEDs) ==
== User Interface (switches and LEDs) ==
[[File:visionCB-8Mmini-ADV-userinterface.png|center|700px]]
[[File:SpaceCB-8Mplus-ADV-UI.png|center|700px]]




Line 617: Line 802:
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| S305 (black, most on the left) || GPIO4-IO03 || 47k pull-up
| S700 (black, most on the left) || GPIO1_IO11 || -
|-
|-
| S304 || GPIO4-IO02 || 47k pull-up
| S701 || GPIO1_IO10 || -
|-
|-
| S303 || GPIO4-IO01 || 47k pull-up
| S702 || GPIO1_IO09 || -
|-
|-
| S302 (black, most on the right) || GPIO4-IO00 || 47k pull-up
| S703 (black, most on the right) || GPIO1_IO08 || -
|}
|}


Line 633: Line 818:
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| S301 (left, red) || Reset || -
| S704 (red) || Reset || -
|-
| S300 (right) || BOOT-RECOVERY || -
|}
|}


Line 645: Line 828:
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| D303 (most on the left) || GPIO4-IO04|| User LED1, buffered with inverter
| D703 (most on the left) || GPIO1_IO06|| User LED1 buffered with inverter
|-
|-
| D302 || GPIO4-IO05 || User LED2, buffered with inverter
| D702 || GPIO1_IO05 || User LED2 buffered with inverter
|-
|-
| D301 || GPIO4-IO06 || User LED3, buffered with inverter
| D701 || GPIO4_IO04 || User LED3 buffered with inverter
|-
|-
| D300 (most on the right) || GPIO4-IO07 || User LED4, buffered with inverter
| D700 (most on the right) || GPIO1_IO07 || User LED4 buffered with inverter
|}
|}
<b>Note: version 1.1 of the SpaceCB-8Mplus has incorrect LEDs description - IO6 and IO4 are changed on PCB top overlay!</b>




Line 661: Line 846:
! style="text-align: center; font-weight: bold;" | Description
! style="text-align: center; font-weight: bold;" | Description
|-
|-
| D304 || SYS-LED|| System function monitoring
| D704 || SAI2_TXC|| System function monitoring (heartbeat) connected to SAI2_TXC (AH15 pin of MPU)
|-
|-
| D305 || - || Power LED (3.3V)
| D705 || - || Power LED (3.3V)
|}
|}
</center>
</center>


== Dimensions ==
== Dimensions ==
[[File:visioncb-8Mmini-ADV-dimensions.png|800px|center]]
[[File:SpaceCB-8Mplus-ADV-v11-dimensions.png|800px|center]]

Latest revision as of 17:10, 15 March 2023

SpaceCB-8Mplus-ADV v.1.1 Datasheet and Pinout

General description

SpaceCB-8Mplus-ADV is a carrier board for the SpaceSOM-8Mplus family of computer-on-modules which are powered by NXP SOC iMX8Mplus (quad core ARM Cortex-A53+ single Cortex-M7 + Neural Processing Unit). A carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as USB 3.0, USB-C, dual gigabit Ethernet, HDMI, PCIe, etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product.
The carrier board connects with the SoM via a standard SODIMM connector.
SpaceCB-8Mplus-ADV carrier board is equipped with HDMI + LVDS + MIPI-DSI video outputs, 24-bit audio codec, PCIe 3.0 (M.2 key M) socket (2242, 2260, 2280), RS-485 and CAN-FD interfaces.
SpaceCB-8Mplus-ADV carrier board is equipped with Segger J-Link debugger and Linux serial console port on USB vCOM.

Applications

  • AI and ML applications
  • Machine vision equipment
  • Robotics
  • Human-machine Interfaces (HMI)
  • Multimedia
  • Video streaming
  • Industrial embedded Linux computer
  • Home Automation – Smart Home
  • IoT gateways
  • Residential gateways

Features

  • Carrier Board (Base Board) compatible with the SpaceSOM-8Mplus family of modules based on quad core, heterogenous NXP iMX8Mplus application processors
  • SoM Interface: SODIMM260
  • Debug Interface: built-in Segger J-Link JTAG debugger
  • Expansion Connectors:
    • Serial communication/GPIO connector 2x8 Pin Header (Male)
    • MicroSD card socket
  • Communication Connectors:
    • PCIe 3.0 (single lane, M.2 key M socket)
    • RS-485 (simplex, 3 pin 2.54mm connector)
    • 2x CAN-FD (3 pin 2.54mm connector)
    • 2x Ethernet 10/100/1000Mbit/s, RJ45
    • 1x USB Host 3.0
    • 1x USB C
    • 1x Console + JTAG MicroUSB B connector
  • Display Interface:
    • 1x HDMI
    • 1x MIPI-DSI (FFP/FPC30)
    • 2x LVDS (FFP/FPC22)
  • Camera Interface:
    • 2x MIPI-CSI2 (FFC/FPC30)
  • User Interface:
    • 24-bit audio codec
    • Line and microphone inputs
    • Speaker or headphone outputs
    • 4+1 Pushbuttons
    • 4+3 LEDs
  • External Power Supply 9-12V DC
  • Temperature Range: 0 to +70°C
  • Board Size: 160mm x 100mm x 25mm

Pictures of SpaceCB-8Mplus-ADV v1.1 board

Version Photo
SpaceCB-8Mplus-ADV v1.1
board only
SpaceCB-8Mplus-ADV v1.1
with SpaceSOM-8Mplus
SpaceCB-8Mplus-ADV
with SpaceSOM-8Mplus
and M.2 SSD drive

Ordering info

SpaceCB-8Mplus-ADV v1.1

Block Diagram

Electrical parameters

Parameter Value Units Comment
Min. Typ. Max.
Power Supply 9.0 12.0 15.0 V Positive pole on central connector of J101
Supply current - - 0.8 A Excluding LCD, USB and another external loads
MIPI-DSI Power Supply (logic) 3.25 3.3 3.35 V -
MIPI-DSI Power Supply (backlight and aux) 4.85 5 5.1 V -
LVDS Power Supply
(aux, up to 100mA) 		4.85 5 5.1 V -

Important information

1. The SpaceCB-8M-ADV carrier board is equippped with dual triple-speed 10/100/1000Mb/s Ethernet interface - RTL8211F. Chips are connected to MPU using RGMII interface.
2. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
3. The I2C2 interface supports on-board audio codec (NAU88C22YG).
4. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).
5. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.
6. The I2C6 interface supports PI5USB30213A USB-C interface controller. Both I2C6_SDA and I2C6_SCL lines are equipped with pull-up resistors (4.7kOhm) installed on SpaceSOM-8Mplus and not on SpaceCB-8Mplus-ADV.
7. The SPI1 interface supports display controller connected to LVDS1 (J550).
8. The SPI2 interface supports display controller connected to LVDS2 (J551).
9. All default I2C interface lines (both: SDA and SCL of I2C1, I2C2, I2C3 and I2C4) have pull-up resistors (4.7kOhm).
10. User LEDs and System LED are connected to MPU using buffers with logical inverters.

M.2 socket - key M (PCIe interface, J600)

Note:
1. Lines CONFIG0...CONFIG3 of M.2 are permanently connected to +3.3V (CONFIG[3..0]=1111b).
2. Implemented PCIe is single lane interface.
3. M.2 socket is key M type.

Camera MIPI-CSI interface (J500 and J501, FPC/FFC 0.5mm)


Pin description of J500 (MIPI-CSI1)
Pin Default MPU pin name MPU pin Description
1 GND - -
2 CSI-CLK-P - -
3 CSI-CLK-P - -
4 GND - -
5 CSI-DATA0-P - -
6 CSI-DATA0-N - -
7 GND - -
8 CSI-DATA1-P - -
9 CSI-DATA1-N - -
10 GND - -
11 CSI-DATA2-P - -
12 CSI-DATA2-N - -
13 GND -
14 CSI-DATA3-P - -
15 CSI-DATA3-N - -
16 GND - -
17 I2C1.SCL AC8 Confguration I2C interface with 4.7kOhm pull-up (3.3V)
18 I2C1.SDA AH7 Confguration I2C interface with 4.7kOhm pull-up (3.3V)
19 GND - -
20 GPIO1_IO0 A7 GPIO1.00 (display RES)
21 GPIO1_IO3 D6 GPIO1.03 (dislpay PWRDN)
22 - - -
23 GND - -
24 +3.3V - Power supply for external devices
25 +3.3V - Power supply for external devices
26 +5V - Power supply for external devices
27 +5V - Power supply for external devices
28 - - -
29 - - -
30 GND - -
Pin description of J501 (MIPI-CSI2)
Pin Default MPU pin name MPU pin Description
1 GND - -
2 CSI-CLK-P - -
3 CSI-CLK-P - -
4 GND - -
5 CSI-DATA0-P - -
6 CSI-DATA0-N - -
7 GND - -
8 CSI-DATA1-P - -
9 CSI-DATA1-N - -
10 GND - -
11 CSI-DATA2-P - -
12 CSI-DATA2-N - -
13 GND -
14 CSI-DATA3-P - -
15 CSI-DATA3-N - -
16 GND - -
17 I2C4.SCL AF8 Confguration I2C interface with 4.7kOhm pull-up (3.3V)
18 I2C4.SDA AD8 Confguration I2C interface with 4.7kOhm pull-up (3.3V)
19 GND - -
20 UART1_RXD AD6 GPIO5.22 (display RES)
21 UART1_TXD AJ3 GPIO5.23 (dislpay PWRDN)
22 - - -
23 GND - -
24 +3.3V - Power supply for external devices
25 +3.3V - Power supply for external devices
26 +5V - Power supply for external devices
27 +5V - Power supply for external devices
28 - - -
29 - - -
30 GND - -


Note:
1. 1st pins of J500/J501 connectors are at the top of the image.
2. J500 is located on the picture first from above (MIPI-CSI1).
3. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
4. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.

Display MIPI-DSI interface (J502, FPC/FFC 0.5mm)

J502 pin Default MPU pin name MPU pin Description
1 GND - -
2 DSI-CLK-P - -
3 DSI-CLK-P - -
4 GND - -
5 DSI-DATA0-P - -
6 DSI-DATA0-N - -
7 GND - -
8 DSI-DATA1-P - -
9 DSI-DATA1-N - -
10 GND - -
11 DSI-DATA2-P - -
12 DSI-DATA2-N - -
13 GND -
14 DSI-DATA3-P - -
15 DSI-DATA3-N - -
16 GND - -
17 I2C1.SCL AC8 Display confguration I2C interface with 4.7kOhm pull-up (3.3V)
18 I2C1.SDA AH7 Display confguration I2C interface with 4.7kOhm pull-up (3.3V)
19 GND - -
20 SAI3_TXC AH19 Optional touch-panel reset signal (CODEC.TXC)
21 I2C3.SDA F13 Optional touch-panel interrupt signal
22 I2C3.SCL AF9 Optional touch-panel controller reset
23 GND - -
24 +3.3V - Power supply for external devices
25 +3.3V - Power supply for external devices
26 +5V - Power supply for external devices
27 +5V - Power supply for external devices
28 GPIO1.01 E8 Optional backlight intensity PWM controller
29 SAI3_TXFS AC16 Optional backlight enable (CODEC.TXFS)
30 GND - -

Note:
1. 1st pin of J502 connector is at the top of the image.
2. For configuration purposes is used I2C1 interface.
3. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
4. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).


Display HDMI interface (J552)

J552 pin Default MPU pin name MPU pin Description
1 HDMI_TX2_P AH27 TMDS_D2_P
2 - - GND
3 HDMI_TX2_N AJ27 TMDS_D2_N
4 HDMI_TX1_P AH26 TMDS_D1_P
5 - - GND
6 HDMI_TX1_N AJ26 TMDS_D1_N
7 HDMI_TX0_P AH25 TMDS_D0_P
8 - - GND
9 HDMI_TX0_N AJ25 TMDS_D0_N
10 HDMI_TXC_P AH24 TMDS_CLK_P
11 - - GND
12 HDMI_TXC_N AJ24 TMDS_CLK_N
13 HDMI_CEC AD22 CEC
14 EARC_P_UTIL AJ23 AUX_P
15 HDMI_DDC_SCL AC22 DDC_CLK
16 HDMI_DDC_SDA AF22 DDC_DAT
17 - - GND
18 - - +5V
19 EARC_N_HPD AH22 HPD/AUX_N

LVDS display interfaces (J550 and J551, FPC/FFC 0.5mm)

Pin description of J550 (LVDS1)
J550 pin Default MPU pin name MPU pin Description
1 GND - -
2 LVDS1.DATA0_N - -
3 LVDS1.DATA0_P - -
4 GND - -
5 LVDS1.DATA1_N - -
6 LVDS1.DATA1_P - -
7 GND - -
8 LVDS1.DATA2_N - -
9 LVDS1.DATA2_P - -
10 GND - -
11 LVDS1.CLK_N - -
12 LVDS1.CLK_P - -
13 GND -
14 LVDS1.DATA3_N - -
15 LVDS1.DATA3_P - -
16 ECSPI1_MOSI AC20 Backlight on/off
17 ECSPI1_MISO AD20 Backlight brightness control (PWM)
18 ECSPI1_CS0 AE20 For optional use
19 I2C4.SCL AF8 Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
20 I2C4.SDA AD8 Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
21 +5V - Power supply for external devices
22 +5V - Power supply for external devices
Pin description of J551 (LVDS2)
J551 pin Default MPU pin name MPU pin Description
1 GND - -
2 LVDS2.DATA0_N - -
3 LVDS2.DATA0_P - -
4 GND - -
5 LVDS2.DATA1_N - -
6 LVDS2.DATA1_P - -
7 GND - -
8 LVDS2.DATA2_N - -
9 LVDS2.DATA2_P - -
10 GND - -
11 LVDS2.CLK_N - -
12 LVDS2.CLK_P - -
13 GND -
14 LVDS2.DATA3_N - -
15 LVDS2.DATA3_P - -
16 ECSPI2_CS0 AJ22 Backlight on/off
17 ECSPI2_MOSI AJ21 Backlight brightness control (PWM)
18 ECSPI2_MISO AH20 For optional use
19 I2C1.SCL AC8 Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
20 I2C1.SDA AH7 Touch-panel confguration I2C interface with 4.7kOhm pull-up (3.3V)
21 +5V - Power supply for external devices
22 +5V - Power supply for external devices


Note:
1. 1st pins of LVDS connectors are located on the left.
2. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
3. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.


MicroSD card connector (J701)

J701 pin Default MPU pin name MPU pin Description
1 SD1_DATA2 V29 DATA2
2 SD1_DATA3 V28 DATA3
3 SD1_SMD W29 CMD
4 1.8/3.3V - VDD (uSD power supply)
selected internally with SAI5_RXD0
5 SD1_CLK W28 CLK
6 - - GND
7 SD1_DATA0 Y29 DATA0
8 SD1_DATA1 Y28 DATA1
SW SD1_RESET_B W25 Card Detect

Note:
1. Value of VDD for uSD is selected with SAI5_RXD0 (MPU) pin.

USB-C interface

Note:
1. USB-C interface built-in SpaceCB-8Mplus-ADV is connected to USB1 channel.
2. The I2C6 interface supports configuration of PI5USB30213A USB-C controller.

USB 3.0 interface

USB 3.0 interface built-in SpaceCB-8Mplus-ADV is connected to USB2 channel.

USB Console Port and Segger J-Link debugger

MPU Port Default MPU pin name Description
CONSOLE-TXD UART4-TXD TXD line of console port
CONSOLE-RXD UART4-RXD RXD line of console port

Notes:
1. Linux console port (UART4 in MPU) uses vCOM interface provided by built-in debugger Segger J-Link.
2. vCOM can be disconnected from MPU with jumper CON (position ON or OFF).
3. Debug JTAG interface can be disconnected from MPU with jumper J-LINK (position ON or OFF).
4. J-Link activity is monitored with ACT LED.

24-bit stereo audio codec


The SpaceCB-8M-ADV board is equipped with 24-bit stereo codec - Nuvoton NAU88C22YG - with integrated audio amplifier.
The NAU88C22 is a low power, high quality CODEC for portable and general purpose audio applications. In addition to precision 24-bit stereo ADCs and DACs, NAU88C22YG integrates a broad range of additional functions to simplify implementation of complete audio system solutions. The NAU88C22 includes drivers for speaker, headphone, and differential or stereo line outputs, and integrates preamps for stereo differential microphones,significantly reducing external component requirements.

Default MPU pin name MPU pin Description
SAI3_MCLK AJ20 Codec master clock
SAI3_TXC AH19 Codec BCLK line
SAI3_TXFS AC16 Codec FS line
SAI3_TXD AH18 Codec input line
SAI3_RXD AF18 Codec output line
I2C2_SCL AH6 Confguration I2C interface with 4.7kOhm pull-up (3.3V)
I2C1_SDA AE8 Confguration I2C interface with 4.7kOhm pull-up (3.3V)

Dual CAN-FD serial interface


The SpaceCB-8Mplus-ADV board is equipped with Microchip CAN-FD with physical layer interfaces MCP2542FD-E/SN, connected to internal CAN1 and CAN2 channels.

Signal Default MPU pin name MPU pin
CAN1.TX SPDIF_TX AE18
CAN1.RX SPDIF_RX AD18
CAN2.TX SAI2_RXC AH16
CAN2.RX SAI2_MCLK AJ15

RS-485 semiduplex serial interface


The SpaceCB-8Mplus-ADV board is equipped with low-voltage RS-485 physical layer interface MAX3485.
The RS-485 is connected to default UART2 (TxD, RxD) channel and pins. Transmission control line DE is controlled by MPU GPIO.

Signal Default MPU pin name Description
RO UART2_RXD Data received by MPU
DI UART2_TXD Data transmitted by MPU
DE GPIO5.05 Transmitter Enable (active high) signal

Note:
1. nRE line of MAX3485 is permanently connected to GND.

GPIO header (J702)


J702 pin Default pin name Description
1 - +3.3V
2 - +5V
3 I2C1_SDA I2C interface with 4.7kOhm pull-up (3.3V)
4 - +5V
5 I2C1_SCL I2C interface with 4.7kOhm pull-up (3.3V)
6 - GND
7 GPIO1.04 -
8 UART3_TXD -
9 - GND
10 UART3_RXD -
11 GPIO1.05 -
12 I2C3_SCL I2C interface with 4.7kOhm pull-up (3.3V)
13 GPIO1_06 -
14 - GND
15 GPIO1_07 -
16 NC Not connected
17 - +3.3V
18 NC Not connected
19 ECSPI2_MOSI -
20 - GND
21 ECSPI2_MISO -
22 GPIO1_08 -
23 ECSPI2_SCLK -
24 ECSPI2_CS0 -
25 - GND
26 GPIO1_09 -
27 I2C4_SDA I2C interface with 4.7kOhm pull-up (3.3V)
28 I2C4_SCL I2C interface with 4.7kOhm pull-up (3.3V)
29 NC Not connected
30 - GND
31 NC Not connected
32 GPIO1_10 -
33 I2C3_SDA I2C interface with 4.7kOhm pull-up (3.3V)
34 - GND
35 ECSPI1_MISO -
36 GPIO1_11 -
37 ECSPI1_CS0 -
38 ECSPI1_MOSI -
39 - GND
40 ECSPI1_SCLK -

Note:
1. The I2C1 interface is common to MIPI-DSI, MIPI-CSI1 and LVDS2 interfaces.
2. The I2C3 interface supports touch-panel controller connected to MIPI-DSI interface (J502).
3. The I2C4 interface is common to MIPI-CSI2 and LVDS1 interfaces.

User Interface (switches and LEDs)


User switches

Switch GPIO Description
S700 (black, most on the left) GPIO1_IO11 -
S701 GPIO1_IO10 -
S702 GPIO1_IO09 -
S703 (black, most on the right) GPIO1_IO08 -


System switches

Switch Signal name Description
S704 (red) Reset -


User LEDs

LED GPIO Description
D703 (most on the left) GPIO1_IO06 User LED1 buffered with inverter
D702 GPIO1_IO05 User LED2 buffered with inverter
D701 GPIO4_IO04 User LED3 buffered with inverter
D700 (most on the right) GPIO1_IO07 User LED4 buffered with inverter

Note: version 1.1 of the SpaceCB-8Mplus has incorrect LEDs description - IO6 and IO4 are changed on PCB top overlay!


System LEDs

LED GPIO Description
D704 SAI2_TXC System function monitoring (heartbeat) connected to SAI2_TXC (AH15 pin of MPU)
D705 - Power LED (3.3V)

Dimensions

Retrieved from "https://wiki.somlabs.com/index.php?title=SpaceCB-8Mplus-ADV_Datasheet_and_Pinout&oldid=3298"