VisionCB-RT-STD v.1.0 Datasheet and Pinout: Difference between revisions

Revision as of 09:27, 12 September 2019

VisionCB-RT-STD v.1.0 Datasheet and Pinout

General description

VisionCB-RT-STD is a carrier board for the VisionSOM family of computer-on-modules which are powered by NXP i.MX RT application processors (ARM Cortex-M7). A carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as USB, Ethernet, UART, etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product.

The carrier board connects with the SoM via a standard SODIMM connector.

Applications

Industrial embedded Linux computer
Home Appliances
Home Automation – Smart Home
Human-machine Interfaces (HMI)
Point-of-sales (POS) terminals
Cash Register
2D barcode scanners and printers
Smart grid Infrastructure
IoT gateways
Residential getaways
Machine vision equipment
Robotics
Fitness/outdoor equipment

Features

Carrier Board (Base Board) compatible with the VisionSOM family of modules based on NXP i.MX RT application processors
Core clock up to 600MHz
Up to 512kB on-chip RAM (depends on used VisionSOM module)
Up to 16MB QSPI Flash memory (depends on used VisionSOM module)
SoM Interface: SODIMM200
Expansion Connectors:
- Arduino Uno Rev. 3 1x8, 1x6, 1x8, 1x10 Pin Headers (Female)
- Raspberry Pi compatible connectors 2x20 Pin Header (Male)
Communication Connectors:
- 1x JTAG connector
- 1x J-Trace connector
- 1x Ethernet 10/100Mbit/s, RJ45
- 1x USB Host Type A connectors
- 1x USB Micro AB connector
- 1x Console MicroUSB B connector (via FTDI FT230 UART to USB converter)
Display Interface: 50-pin FFC/FPC Parallel RGB – 24-bit, (1366 x 768 Max. Resolution)
User Interface:
- 5 Pushbuttons
- 5 LEDs
Boot selector
Power Supply
- DC connector: Input Voltage 9-12V DC (5.5x2.1 connector)
- MicroUSB connector: Input Voltage 5V DC
Temperature Range: 0 to +70°C
Board Size: 145mm x 90mm x 17mm

Pictures of VisionCB-RT-STD v1.0 board

Version	Photo
VisionCB-RT-STD v1.0 board only
VisionCB-RT-STD v1.0 board with VisionSOM-6ULL

Ordering info

VisionCB-RT-STD v1.0

Block Diagram

Electrical parameters

Parameter	Value			Units	Comment
Parameter	Min.	Typ.	Max.	Units	Comment
Power Supply (J100 input)	9.0	11.0	12.0	V	Positive pole on central connector of J100
Supply current	-	-	0.15	A	Excluding LCD, USB and antoher external loads
USB power supply	4.75	4.9	5.5	V	On J201 (Linux USB console connector)
Input GPIO voltage (J405)	0	-	3.3	V	LCD-RGB connector
Input GPIO voltage (J504)	0	-	3.3	V	Raspberry Pi compatible
Input GPIO voltage (J502, J503)	0	-	3.3/5	V	Arduino compatible connector (digital I/O)
Input GPIO voltage (J501)	0	-	3.3	V	Arduino compatible connector (analog inputs)

Boot Selector

BOOTx		Boot Mode
BOOT1 GPIO_AD_B0_05	BOOT0 GPIO_AD_B0_04	Boot Mode
1	1	Reserved
1	0	Internal
0	1	Serial
0	0	Fuses

JTAG & JTAG+ETM Connectors

JTAG Connector	Default function name	MCU pin name
1	VCC-3V3	NA
2	-	NA
3	-	NA
4	GND	NA
5	JTAG-TDI	GPIO_AD_B0_09
6	GND	NA
7	JTAG-TMS	GPIO_AD_B0_06
8	GND	NA
9	JTAG-TCK	GPIO_AD_B0_07
10	GND	NA
11	-	NA
12	GND	NA
13	JTAG-TDO	GPIO_AD_B0_10
14	-	NA
15	POR-B	POR-B
16	-	NA
17	-	NA
18	-	NA
19	5V-Supply (IN)	NA
20	-	NA

JTAG+ETM Connector	Default function name	MCU pin name
1	VCC-3V3	NA
2	JTAG-TMS	GPIO_AD_B0_06
3	GND	NA
4	JTAG-TCK	GPIO_AD_B0_07
5	GND	NA
6	JTAG-TDO	GPIO_AD_B0_10
7	-	NA
8	JTAG-TDI	GPIO_AD_B0_09
9	-	NA
10	POR-B	POR-B
11	5V-Supply (IN)	NA
12	LCD-DATA13	GPIO_B0_12
13	5V-Supply (IN)	NA
14	LCD-DATA3	GPIO_B0_04
15	GND	NA
16	LCD-DATA4	GPIO_B0_05
17	GND	NA
18	LCD-DATA5	GPIO_B0_06
19	GND	NA
20	LCD-DATA6	GPIO_B0_07

VisionCB-RT-STD v.1.0 Datasheet and Pinout

General description

VisionCB-RT-STD is a carrier board for the VisionSOM family of computer-on-modules which are powered by NXP i.MX RT application processors (ARM Cortex-M7). A carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as USB, Ethernet, UART, etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product.

The carrier board connects with the SoM via a standard SODIMM connector.

Applications

Industrial embedded Linux computer
Home Appliances
Home Automation – Smart Home
Human-machine Interfaces (HMI)
Point-of-sales (POS) terminals
Cash Register
2D barcode scanners and printers
Smart grid Infrastructure
IoT gateways
Residential getaways
Machine vision equipment
Robotics
Fitness/outdoor equipment

Features

Carrier Board (Base Board) compatible with the VisionSOM family of modules based on NXP i.MX RT application processors
Core clock up to 600MHz
Up to 512kB on-chip RAM (depends on used VisionSOM module)
Up to 16MB QSPI Flash memory (depends on used VisionSOM module)
SoM Interface: SODIMM200
Expansion Connectors:
- Arduino Uno Rev. 3 1x8, 1x6, 1x8, 1x10 Pin Headers (Female)
- Raspberry Pi compatible connectors 2x20 Pin Header (Male)
Communication Connectors:
- 1x JTAG connector
- 1x J-Trace connector
- 1x Ethernet 10/100Mbit/s, RJ45
- 1x USB Host Type A connectors
- 1x USB Micro AB connector
- 1x Console MicroUSB B connector (via FTDI FT230 UART to USB converter)
Display Interface: 50-pin FFC/FPC Parallel RGB – 24-bit, (1366 x 768 Max. Resolution)
User Interface:
- 5 Pushbuttons
- 5 LEDs
Boot selector
Power Supply
- DC connector: Input Voltage 9-12V DC (5.5x2.1 connector)
- MicroUSB connector: Input Voltage 5V DC
Temperature Range: 0 to +70°C
Board Size: 145mm x 90mm x 17mm

Pictures of VisionCB-RT-STD v1.0 board

Version	Photo
VisionCB-RT-STD v1.0 board only
VisionCB-RT-STD v1.0 board with VisionSOM-6ULL

Ordering info

VisionCB-RT-STD v1.0

Block Diagram

Electrical parameters

Parameter	Value			Units	Comment
Parameter	Min.	Typ.	Max.	Units	Comment
Power Supply (J100 input)	9.0	11.0	12.0	V	Positive pole on central connector of J100
Supply current	-	-	0.15	A	Excluding LCD, USB and antoher external loads
USB power supply	4.75	4.9	5.5	V	On J201 (Linux USB console connector)
Input GPIO voltage (J405)	0	-	3.3	V	LCD-RGB connector
Input GPIO voltage (J504)	0	-	3.3	V	Raspberry Pi compatible
Input GPIO voltage (J502, J503)	0	-	3.3/5	V	Arduino compatible connector (digital I/O)
Input GPIO voltage (J501)	0	-	3.3	V	Arduino compatible connector (analog inputs)

Boot Selector

BOOTx		Boot Mode
BOOT1 GPIO_AD_B0_05	BOOT0 GPIO_AD_B0_04	Boot Mode
1	1	Reserved
1	0	Internal
0	1	Serial
0	0	Fuses

JTAG & JTAG+ETM Connectors

JTAG Connector	Default function name	MCU pin name
1	VCC-3V3	NA
2	-	NA
3	-	NA
4	GND	NA
5	JTAG-TDI	GPIO_AD_B0_09
6	GND	NA
7	JTAG-TMS	GPIO_AD_B0_06
8	GND	NA
9	JTAG-TCK	GPIO_AD_B0_07
10	GND	NA
11	-	NA
12	GND	NA
13	JTAG-TDO	GPIO_AD_B0_10
14	-	NA
15	POR-B	POR-B
16	-	NA
17	-	NA
18	-	NA
19	5V-Supply (IN)	NA
20	-	NA

JTAG+ETM Connector	Default function name	MCU pin name
1	VCC-3V3	NA
2	JTAG-TMS	GPIO_AD_B0_06
3	GND	NA
4	JTAG-TCK	GPIO_AD_B0_07
5	GND	NA
6	JTAG-TDO	GPIO_AD_B0_10
7	-	NA
8	JTAG-TDI	GPIO_AD_B0_09
9	-	NA
10	POR-B	POR-B
11	5V-Supply (IN)	NA
12	LCD-DATA13	GPIO_B0_12
13	5V-Supply (IN)	NA
14	LCD-DATA3	GPIO_B0_04
15	GND	NA
16	LCD-DATA4	GPIO_B0_05
17	GND	NA
18	LCD-DATA5	GPIO_B0_06
19	GND	NA
20	LCD-DATA6	GPIO_B0_07

Raspberry Pi compatible I/O header (J504)

J504 Pin	Default function name	MCU pin name	Description
1	VCC-3V3	NA	+3.3V generated by internal SOM LDO converter (limited load current).
2	VCC-5V0	NA	+5V generated by carrier board built-in DC/DC converter.
3	UART5-RXD	Default: UART5 RxD input or universal GPIO with 3.3V logic levels.
4	VCC-5V0	NA	+5V generated by carrier board built-in DC/DC converter.
5	UART5-TXD	Default: UART5 TxD output or universal GPIO with 3.3V logic levels.
6	GND	NA	-
7	ENET2_TXD0	Default: ENET2 TXD0 line or universal GPIO with 3.3V logic levels.
8	UART4-TXD	Default: UART4 TXD output or universal GPIO with 3.3V logic levels.
9	GND	NA	-
10	UART4-RXD	Default: UART4 RXD input or universal GPIO with 3.3V logic levels.
11	ENET2_CRS_DV	Default: ENET2 CRS_DV line or universal GPIO with 3.3V logic levels.
12	GPIO5	Universal GPIO with 3.3V logic levels.
13	UART1-CTS	Default: UART1 CTS line or universal GPIO with 3.3V logic levels.
14	GND	NA	-
15	UART1-RTS	Default: UART1 RTS line or universal GPIO with 3.3V logic levels.
16	GPIO8	Universal GPIO with 3.3V logic levels.
17	VCC-3V3	NA	+3.3V generated by internal SOM LDO converter (limited load current)
18	GPIO9	Universal GPIO with 3.3V logic levels.
19	UART2-CTS	Default: UART2 CTS line or universal GPIO with 3.3V logic levels.
20	GND	NA	-
21	UART2-RTS	Default: UART2 RTS line or universal GPIO with 3.3V logic levels.
22	GPIO0	Universal GPIO with 3.3V logic levels.
23	UART2-RXD	Default: UART2 RXD input or universal GPIO with 3.3V logic levels.
24	UART2-TXD	Default: UART2 TXD input or universal GPIO with 3.3V logic levels.
25	GND	NA	-
26	ENET2_TXEN	Default: ENET2 TXEN line or universal GPIO with 3.3V logic levels.
27	-	NA	-
28	-	NA	-
29	ENET2_TX_CLK	Default: ENET2 TX_CLK line or universal GPIO with 3.3V logic levels.
30	GND	NA	-
31	ENET2_RXER	Default: ENET2 RXER line or universal GPIO with 3.3V logic levels.
32	JTAG-MOD	Default: JTAG MOD input or universal GPIO with 3.3V logic levels.
33	UART3-CTS	Default: UART3 CTS line or universal GPIO with 3.3V logic levels.
34	GND	NA	-
35	UART3-RTS	Default: UART3 RTS line or universal GPIO with 3.3V logic levels.
36	JTAG-TDO	Default: JTAG TDO output or universal GPIO with 3.3V logic levels.
37	ENET2_RXD1	Default: ENET2 RXD1 line or universal GPIO with 3.3V logic levels.
38	JTAG-TDI	Default: JTAG TDI input or universal GPIO with 3.3V logic levels.
39	GND	NA	-
40	JTAG-TMS	Default: JTAG TMS output or universal GPIO with 3.3V logic levels.

Arduino compatible I/O headers (J500-J503)

Pin	Arduino name	Default function name	Description
Power connector J500, red connector
1	-	-	-
2	IOREF	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
3	RESET	POR-B	External warm reset input, active L.
4	3.3V	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
5	5V	VCC-5V0	+5V generated by carrier board built-in DC/DC converter.
6	GND	GND	-
7	GND	GND	-
8	VIN	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
Analog inputs connector J501, blue connector
1	AIN0	GPIO1	Universal GPIO with 3.3V logic levels.
2	AIN1	GPIO5	Universal GPIO with 3.3V logic levels.
3	AIN2	GPIO8	Universal GPIO with 3.3V logic levels.
4	AIN3	GPIO9	Universal GPIO with 3.3V logic levels.
5	-	-	-
6	-	-	-
Digital I/Os connector J503, yellow connector
1	DIO0	UART4-RXD	Default: UART4 RXD line or universal GPIO with 5V logic levels.
2	DIO1	UART4-TXD	Default: UART4 TXD line or universal GPIO with 5V logic levels.
3	DIO2	UART3-RTS	Default: UART3 RTS line or universal GPIO with 5V logic levels.
4	DIO3	UART3-CTS	Default: UART3 CTS line or universal GPIO with 5V logic levels.
5	DIO4	ENET2_RXER	Default: ENET2 RX ER line or universal GPIO with 5V logic levels.
6	DIO5	ENET2_TX_CLK	Default: ENET2 TX CLK line or universal GPIO with 5V logic levels.
7	DIO6	UART1-RTS	Default: UART1 RTS line or universal GPIO with 5V logic levels.
8	DIO7	UART1-CTS	Default: UART1 CTS line or universal GPIO with 5V logic levels.
Digital I/Os connector J502, yellow connector
1	DIO8	ENET2_TXD0	Default: ENET2 TXD0 line or universal GPIO with 5V logic levels.
2	DIO9	ENET2_CRS_DV	Default: ENET2 CRS DV line or universal GPIO with 5V logic levels.
3	DIO10	UART2-TXD	Default: UART2 TXD line or universal GPIO with 5V logic levels.
4	DIO11	UART2-CTS	Default: UART2 CTS line or universal GPIO with 5V logic levels.
5	DIO12	UART2-RTS	Default: UART2 RTS line or universal GPIO with 5V logic levels.
6	DIO13	UART2-RXD	Default: UART2 RXD line or universal GPIO with 5V logic levels.
7	GND	GND	-
8	AREF	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
9	DIO14-SCL	UART5-RXD	Default: UART5 RXD line or universal GPIO with 5V logic levels.
10	DIO15-SDA	UART5-TXD	Default: UART5 TXD line or universal GPIO with 5V logic levels.

Notes:
1. All I/O lines are 5V compatible.
2. RESET line is 5V compatible.
3. Preferred voltage range on AIN0…AIN3 lines is 0…+3.3V.
4. Voltage level compatibility can be changed to +3.3V with removing R901 and mouting R902 (0R), but voltage range on AIN0…AIN3 lines must be 0…+3.3V.

User LEDs connections

LED	PCB symbol	GPIO	Description
D400/blue	GPIO10	GPIO1_10	Default: JTAG MOD input or universal GPIO with 3.3V logic levels.
D401/green	GPIO11	GPIO1_11	Default: JTAG TMS input or universal GPIO with 3.3V logic levels.
D403/yellow	GPIO12	GPIO1_12	Default: JTAG TDO input or universal GPIO with 3.3V logic levels.
D402/red	GPIO13	GPIO1_13	Default: JTAG TDI input or universal GPIO with 3.3V logic levels.

Notes:
1. LEDs are switched on by logic „1” set at the GPIO outputs.
2. LEDs are controlled by current drivers and do not load the GPIOs.

User switches connections

Switch	PCB symbol	GPIO	Description
S402	GPIO3	GPIO1_IO03	Universal GPIO with 3.3V logic levels.
S403	GPIO4	GPIO1_IO04	Universal GPIO with 3.3V logic levels.
S404	GPIO8	GPIO1_IO08	Universal GPIO with 3.3V logic levels.
S405	GPIO9	GPIO1_IO09	Universal GPIO with 3.3V logic levels.

Notes:
1. After button pressing on GPIO lines are set to „0”.
2. GPIO lines connected to switches are separated from board’s environment by 1k resistors.

TFT LCD connector (RGB 24b, J405)

J405 pin	Default function name	LCD interface name
1	LCD-DATA0	LCD-B0
2	LCD-DATA1	LCD-B1
3	LCD-DATA2	LCD-B2
4	LCD-DATA3	LCD-B3
5	LCD-DATA4	LCD-B4
6	LCD-DATA5	LCD-B5
7	LCD-DATA6	LCD-B6
8	LCD-DATA7	LCD-B7
9	GND	GND
10	LCD-DATA8	LCD-G0
11	LCD-DATA9	LCD-G1
12	LCD-DATA10	LCD-G2
13	LCD-DATA11	LCD-G3
14	LCD-DATA12	LCD-G4
15	LCD-DATA13	LCD-G5
16	LCD-DATA14	LCD-G6
17	LCD-DATA15	LCD-G7
18	GND	GND
19	LCD-DATA16	LCD-R0
20	LCD-DATA17	LCD-R1
21	LCD-DATA18	LCD-R2
22	LCD-DATA19	LCD-R3
23	LCD-DATA20	LCD-R4
24	LCD-DATA21	LCD-R5
25	LCD-DATA22	LCD-R6
26	LCD-DATA23	LCD-R7
27	GND	GND
28	LCD-DE	DE
29	LCD-HSYNC	HSYNC
30	LCD-VSYNC	VSYNC
31	GND	GND
32	LCD-PCLK	DCLK
33	GND	GND
34	GPIO4	TS-YPUL
35	GPIO3	TS-YNUR
36	GPIO2	TS-YPLL
37	GPIO1	TS-YNLR
38	-	-
39	-	-
40	-	-
41	-	-
42	UART5-TXD	I2C-SCL
43	UART5-RXD	I2C-SDA
44	GND	GND
45	VCC-LCD	+3.3V (controlled by ENET2_TXEN)
46	VCC-LCD	+3.3V (controlled by ENET2_TXEN)
47	VCC-5V0	+5.0V
48	VCC-5V0	+5.0V
49	LCD-RESET	RESET
50	JTAG-nTRST	PWREN

Dimensions

Arduino compatible I/O headers (J500-J503)

Pin	Arduino name	Default function name	Description
Power connector J500, red connector
1	-	-	-
2	IOREF	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
3	RESET	POR-B	External warm reset input, active L.
4	3.3V	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
5	5V	VCC-5V0	+5V generated by carrier board built-in DC/DC converter.
6	GND	GND	-
7	GND	GND	-
8	VIN	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
Analog inputs connector J501, blue connector
1	AIN0	GPIO1	Universal GPIO with 3.3V logic levels.
2	AIN1	GPIO5	Universal GPIO with 3.3V logic levels.
3	AIN2	GPIO8	Universal GPIO with 3.3V logic levels.
4	AIN3	GPIO9	Universal GPIO with 3.3V logic levels.
5	-	-	-
6	-	-	-
Digital I/Os connector J503, yellow connector
1	DIO0	UART4-RXD	Default: UART4 RXD line or universal GPIO with 5V logic levels.
2	DIO1	UART4-TXD	Default: UART4 TXD line or universal GPIO with 5V logic levels.
3	DIO2	UART3-RTS	Default: UART3 RTS line or universal GPIO with 5V logic levels.
4	DIO3	UART3-CTS	Default: UART3 CTS line or universal GPIO with 5V logic levels.
5	DIO4	ENET2_RXER	Default: ENET2 RX ER line or universal GPIO with 5V logic levels.
6	DIO5	ENET2_TX_CLK	Default: ENET2 TX CLK line or universal GPIO with 5V logic levels.
7	DIO6	UART1-RTS	Default: UART1 RTS line or universal GPIO with 5V logic levels.
8	DIO7	UART1-CTS	Default: UART1 CTS line or universal GPIO with 5V logic levels.
Digital I/Os connector J502, yellow connector
1	DIO8	ENET2_TXD0	Default: ENET2 TXD0 line or universal GPIO with 5V logic levels.
2	DIO9	ENET2_CRS_DV	Default: ENET2 CRS DV line or universal GPIO with 5V logic levels.
3	DIO10	UART2-TXD	Default: UART2 TXD line or universal GPIO with 5V logic levels.
4	DIO11	UART2-CTS	Default: UART2 CTS line or universal GPIO with 5V logic levels.
5	DIO12	UART2-RTS	Default: UART2 RTS line or universal GPIO with 5V logic levels.
6	DIO13	UART2-RXD	Default: UART2 RXD line or universal GPIO with 5V logic levels.
7	GND	GND	-
8	AREF	VCC-3V3	+3.3V generated by internal SOM LDO converter (limited load current).
9	DIO14-SCL	UART5-RXD	Default: UART5 RXD line or universal GPIO with 5V logic levels.
10	DIO15-SDA	UART5-TXD	Default: UART5 TXD line or universal GPIO with 5V logic levels.

Notes:
1. All I/O lines are 5V compatible.
2. RESET line is 5V compatible.
3. Preferred voltage range on AIN0…AIN3 lines is 0…+3.3V.
4. Voltage level compatibility can be changed to +3.3V with removing R901 and mouting R902 (0R), but voltage range on AIN0…AIN3 lines must be 0…+3.3V.

User LEDs connections

LED	PCB symbol	GPIO	Description
D400/blue	GPIO10	GPIO1_10	Default: JTAG MOD input or universal GPIO with 3.3V logic levels.
D401/green	GPIO11	GPIO1_11	Default: JTAG TMS input or universal GPIO with 3.3V logic levels.
D403/yellow	GPIO12	GPIO1_12	Default: JTAG TDO input or universal GPIO with 3.3V logic levels.
D402/red	GPIO13	GPIO1_13	Default: JTAG TDI input or universal GPIO with 3.3V logic levels.

Notes:
1. LEDs are switched on by logic „1” set at the GPIO outputs.
2. LEDs are controlled by current drivers and do not load the GPIOs.

User switches connections

Switch	PCB symbol	GPIO	Description
S402	GPIO3	GPIO1_IO03	Universal GPIO with 3.3V logic levels.
S403	GPIO4	GPIO1_IO04	Universal GPIO with 3.3V logic levels.
S404	GPIO8	GPIO1_IO08	Universal GPIO with 3.3V logic levels.
S405	GPIO9	GPIO1_IO09	Universal GPIO with 3.3V logic levels.

Notes:
1. After button pressing on GPIO lines are set to „0”.
2. GPIO lines connected to switches are separated from board’s environment by 1k resistors.

TFT LCD connector (RGB 24b, J405)

J405 pin	Default function name	LCD interface name
1	LCD-DATA0	LCD-B0
2	LCD-DATA1	LCD-B1
3	LCD-DATA2	LCD-B2
4	LCD-DATA3	LCD-B3
5	LCD-DATA4	LCD-B4
6	LCD-DATA5	LCD-B5
7	LCD-DATA6	LCD-B6
8	LCD-DATA7	LCD-B7
9	GND	GND
10	LCD-DATA8	LCD-G0
11	LCD-DATA9	LCD-G1
12	LCD-DATA10	LCD-G2
13	LCD-DATA11	LCD-G3
14	LCD-DATA12	LCD-G4
15	LCD-DATA13	LCD-G5
16	LCD-DATA14	LCD-G6
17	LCD-DATA15	LCD-G7
18	GND	GND
19	LCD-DATA16	LCD-R0
20	LCD-DATA17	LCD-R1
21	LCD-DATA18	LCD-R2
22	LCD-DATA19	LCD-R3
23	LCD-DATA20	LCD-R4
24	LCD-DATA21	LCD-R5
25	LCD-DATA22	LCD-R6
26	LCD-DATA23	LCD-R7
27	GND	GND
28	LCD-DE	DE
29	LCD-HSYNC	HSYNC
30	LCD-VSYNC	VSYNC
31	GND	GND
32	LCD-PCLK	DCLK
33	GND	GND
34	GPIO4	TS-YPUL
35	GPIO3	TS-YNUR
36	GPIO2	TS-YPLL
37	GPIO1	TS-YNLR
38	-	-
39	-	-
40	-	-
41	-	-
42	UART5-TXD	I2C-SCL
43	UART5-RXD	I2C-SDA
44	GND	GND
45	VCC-LCD	+3.3V (controlled by ENET2_TXEN)
46	VCC-LCD	+3.3V (controlled by ENET2_TXEN)
47	VCC-5V0	+5.0V
48	VCC-5V0	+5.0V
49	LCD-RESET	RESET
50	JTAG-nTRST	PWREN

Personal tools

VisionCB-RT-STD v.1.0 Datasheet and Pinout: Difference between revisions - SomLabs Wiki

Search

Navigation

Tools

VisionCB-RT-STD v.1.0 Datasheet and Pinout: Difference between revisions

From SomLabs Wiki

Revision as of 09:27, 12 September 2019

Contents

General description

Applications

Features

Pictures of VisionCB-RT-STD v1.0 board

Ordering info

Block Diagram

Electrical parameters

Boot Selector

JTAG & JTAG+ETM Connectors

General description

Applications

Features

Pictures of VisionCB-RT-STD v1.0 board

Ordering info

Block Diagram

Electrical parameters

Boot Selector

JTAG & JTAG+ETM Connectors

Raspberry Pi compatible I/O header (J504)

Arduino compatible I/O headers (J500-J503)

User LEDs connections

User switches connections

TFT LCD connector (RGB 24b, J405)

Dimensions

Arduino compatible I/O headers (J500-J503)

User LEDs connections

User switches connections

TFT LCD connector (RGB 24b, J405)

Dimensions

@@ Line 1: / Line 1: @@
+{{PageHeader|VisionCB-RT-STD v.1.0 Datasheet and Pinout}} __toc__
+__jzpdf__
+== General description ==
+[[File:VisionCB-RT-STD-1-0-1k.png|center|700px]]
+VisionCB-RT-STD is a carrier board for the VisionSOM family of computer-on-modules which are powered by NXP i.MX RT application processors (ARM Cortex-M7). A carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as USB, Ethernet, UART, etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product.
+The carrier board connects with the SoM via a standard SODIMM connector.
+=== Applications ===
+* Industrial embedded Linux computer
+* Home Appliances
+* Home Automation – Smart Home
+* Human-machine Interfaces (HMI)
+* Point-of-sales (POS) terminals
+* Cash Register
+* 2D barcode scanners and printers
+* Smart grid Infrastructure
+* IoT gateways
+* Residential getaways
+* Machine vision equipment
+* Robotics
+* Fitness/outdoor equipment
+== Features ==
+* Carrier Board (Base Board) compatible with the VisionSOM family of modules based on NXP i.MX RT application processors
+* Core clock up to 600MHz
+* Up to 512kB on-chip RAM (depends on used VisionSOM module)
+* Up to 16MB QSPI Flash memory (depends on used VisionSOM module)
+* SoM Interface: SODIMM200
+* Expansion Connectors:
+**Arduino Uno Rev. 3	1x8, 1x6, 1x8, 1x10 Pin Headers (Female)
+**Raspberry Pi compatible connectors	2x20 Pin Header (Male)
+* Communication Connectors:
+** 1x JTAG connector
+** 1x J-Trace connector
+** 1x Ethernet 10/100Mbit/s, RJ45
+** 1x USB Host Type A connectors
+** 1x USB Micro AB connector
+** 1x Console MicroUSB B connector (via FTDI FT230 UART to USB converter)
+* Display Interface: 50-pin FFC/FPC Parallel RGB – 24-bit, (1366 x 768 Max. Resolution)
+* User Interface:
+** 5 Pushbuttons
+** 5 LEDs
+*Boot selector
+* Power Supply
+** DC connector: Input Voltage 9-12V DC (5.5x2.1 connector)
+** MicroUSB connector: Input Voltage 5V DC
+* Temperature Range: 0 to +70°C
+* Board Size: 145mm x 90mm x 17mm
+== Pictures of VisionCB-RT-STD v1.0 board ==
+{| class="wikitable"
+|-
+! Version !! Photo
+|-
+| VisionCB-RT-STD v1.0 board only ||
+[[File:VisionCB-RT-STD-1-0-1k.png|center|thumb]]
+|-
+| VisionCB-RT-STD v1.0 board with VisionSOM-6ULL  ||
+[[File:VisionCB-RT-STD-1-0-z-SOM-1k.png|center|thumb]]
+<!--|--->                                                         <!-- This is a comment -->
+<!--| VisionCB-RT-STD v1.0 board with Raspberry Pi HAT ||-->      <!-- This is a comment -->
+<!--[[File:VisionCB-RT-STD-1-0-shield-rpi.png|center|thumb]]-->   <!-- This is a comment -->
+<!--|--->                                                         <!-- This is a comment -->
+<!--| VisionCB-RT-STD v1.0 board with Arduino Shield ||-->        <!-- This is a comment -->
+<!--[[File:VisionCB-RT-STD-1-0-arduino-1k.png|center|thumb]]-->   <!-- This is a comment -->
+|}
+== Ordering info ==
+__orderingInfoStart__
+[
+      {
+        "type" : "separator",
+        "value" : "VisionCB-RT-STD v1.0"
+    }
+]
+__orderingInfoEnd__
+== Block Diagram ==
+[[File:VisionCB-RT-STD-1-0-block-diagram.png|1000px|center]]
+== Electrical parameters ==
+{| class="wikitable"
+! rowspan="2" style="text-align: center; font-weight: bold;" | Parameter
+! colspan="3" style="text-align: center; font-weight: bold;" | Value
+! rowspan="2" style="text-align: center; font-weight: bold;" | Units
+! rowspan="2" style="text-align: center; font-weight: bold;" | Comment
+|-
+| Min.
+| Typ.
+| Max.
+|-
+| Power Supply (J100 input)
+| 9.0
+| 11.0
+| 12.0
+| V
+| Positive pole on central connector of J100
+|-
+| Supply current
+| -
+| -
+| 0.15
+| A
+| Excluding LCD, USB and antoher external loads
+|-
+| USB power supply
+| 4.75
+| 4.9
+| 5.5
+| V
+| On J201 (Linux USB console connector)
+|-
+| Input GPIO voltage (J405)
+| 0
+| -
+| 3.3
+| V
+| LCD-RGB connector
+|-
+| Input GPIO voltage (J504)
+| 0
+| -
+| 3.3
+| V
+| Raspberry Pi compatible
+|-
+| Input GPIO voltage (J502, J503)
+| 0
+| -
+| 3.3/5
+| V
+| Arduino compatible connector (digital I/O)
+|-
+| Input GPIO voltage (J501)
+| 0
+| -
+| 3.3
+| V
+| Arduino compatible connector (analog inputs)
+|}
+== Boot Selector ==
+[[File:VisionCB-RT-STD-1-0-bootsel.png|center|600px]]
+{| class="wikitable"
+! colspan="2" style="text-align: center; font-weight: bold;" | BOOTx
+! rowspan="2" style="text-align: center; font-weight: bold;" | Boot Mode
+|-
+| BOOT1
+GPIO_AD_B0_05
+| BOOT0
+GPIO_AD_B0_04
+|-
+| 1
+| 1
+|Reserved
+|-
+| 1
+| 0
+|Internal
+|-
+| 0
+| 1
+|Serial
+|-
+| 0
+| 0
+|Fuses
+|}
+== JTAG & JTAG+ETM Connectors ==
+[[File:VisionCB-RT-STD-1-0-jtag_jtrace.png|center|600px]]
+{| class="wikitable"
+!style="text-align: center; font-weight: bold;" | JTAG Connector
+!style="text-align: center; font-weight: bold;" | Default function name
+!style="text-align: center; font-weight: bold;" | MCU pin name
+|-
+|1
+| VCC-3V3
+| NA
+|-
+|2
+| -
+| NA
+|-
+|3
+| -
+| NA
+|-
+|4
+| GND
+| NA
+|-
+|5
+| JTAG-TDI
+| GPIO_AD_B0_09
+|-
+|6
+| GND
+| NA
+|-
+|7
+| JTAG-TMS
+| GPIO_AD_B0_06
+|-
+|8
+| GND
+| NA
+|-
+|9
+| JTAG-TCK
+| GPIO_AD_B0_07
+|-
+|10
+| GND
+| NA
+|-
+|11
+| -
+| NA
+|-
+|12
+| GND
+| NA
+|-
+|13
+| JTAG-TDO
+| GPIO_AD_B0_10
+|-
+|14
+| -
+| NA
+|-
+|15
+| POR-B
+| POR-B
+|-
+|16
+| -
+| NA
+|-
+|17
+| -
+| NA
+|-
+|18
+| -
+| NA
+|-
+|19
+| 5V-Supply (IN)
+| NA
+|-
+|20
+| -
+| NA
+|}
+{| class="wikitable"
+!style="text-align: center; font-weight: bold;" | JTAG+ETM Connector
+!style="text-align: center; font-weight: bold;" | Default function name
+!style="text-align: center; font-weight: bold;" | MCU pin name
+|-
+|1
+| VCC-3V3
+| NA
+|-
+|2
+| JTAG-TMS
+| GPIO_AD_B0_06
+|-
+|3
+| GND
+| NA
+|-
+|4
+| JTAG-TCK
+| GPIO_AD_B0_07
+|-
+|5
+| GND
+| NA
+|-
+|6
+| JTAG-TDO
+| GPIO_AD_B0_10
+|-
+|7
+| -
+| NA
+|-
+|8
+| JTAG-TDI
+| GPIO_AD_B0_09
+|-
+|9
+| -
+| NA
+|-
+|10
+| POR-B
+| POR-B
+|-
+|11
+| 5V-Supply (IN)
+| NA
+|-
+|12
+| LCD-DATA13
+| GPIO_B0_12
+|-
+|13
+| 5V-Supply (IN)
+| NA
+|-
+|14
+| LCD-DATA3
+| GPIO_B0_04
+|-
+|15
+| GND
+| NA
+|-
+|16
+| LCD-DATA4
+| GPIO_B0_05
+|-
+|17
+| GND
+| NA
+|-
+|18
+| LCD-DATA5
+| GPIO_B0_06
+|-
+|19
+| GND
+| NA
+|-
+|20
+| LCD-DATA6
+| GPIO_B0_07
+|}
 {{PageHeader|VisionCB-RT-STD v.1.0 Datasheet and Pinout}} __toc__
 __jzpdf__
@@ Line 529: / Line 874: @@
 | Default: JTAG TMS output or universal GPIO with 3.3V logic levels.
 |}
+== Arduino compatible I/O headers (J500-J503) ==
+[[File:VisionCB-RT-STD-1-0-arduino.png|center|600px]]
+{| class="wikitable"
+! style="text-align: center; font-weight: bold;" | Pin
+! style="text-align: center; font-weight: bold;" | Arduino name
+! style="text-align: center; font-weight: bold;" | Default function name
+! style="text-align: center; font-weight: bold;" | Description
+|-
+| colspan="4" | Power connector J500, red connector
+|-
+| 1
+| -
+| -
+| -
+|-
+| 2
+| IOREF
+| VCC-3V3
+| +3.3V generated by internal SOM LDO converter (limited load current).
+|-
+| 3
+| RESET
+| POR-B
+| External warm reset input, active L.
+|-
+| 4
+| 3.3V
+| VCC-3V3
+| +3.3V generated by internal SOM LDO converter (limited load current).
+|-
+| 5
+| 5V
+| VCC-5V0
+| +5V generated by carrier board built-in DC/DC converter.
+|-
+| 6
+| GND
+| GND
+| -
+|-
+| 7
+| GND
+| GND
+| -
+|-
+| 8
+| VIN
+| VCC-3V3
+| +3.3V generated by internal SOM LDO converter (limited load current).
+|-
+| colspan="4" | Analog inputs connector J501, blue connector
+|-
+| 1
+| AIN0
+| GPIO1
+| Universal GPIO with 3.3V logic levels.
+|-
+| 2
+| AIN1
+| GPIO5
+| Universal GPIO with 3.3V logic levels.
+|-
+| 3
+| AIN2
+| GPIO8
+| Universal GPIO with 3.3V logic levels.
+|-
+| 4
+| AIN3
+| GPIO9
+| Universal GPIO with 3.3V logic levels.
+|-
+| 5
+| -
+| -
+| -
+|-
+| 6
+| -
+| -
+| -
+|-
+| colspan="4" | Digital I/Os connector J503, yellow connector
+|-
+| 1
+| DIO0
+| UART4-RXD
+| Default: UART4 RXD line or universal GPIO with 5V logic levels.
+|-
+| 2
+| DIO1
+| UART4-TXD
+| Default: UART4 TXD line or universal GPIO with 5V logic levels.
+|-
+| 3
+| DIO2
+| UART3-RTS
+| Default: UART3 RTS line or universal GPIO with 5V logic levels.
+|-
+| 4
+| DIO3
+| UART3-CTS
+| Default: UART3 CTS line or universal GPIO with 5V logic levels.
+|-
+| 5
+| DIO4
+| ENET2_RXER
+| Default: ENET2 RX ER line or universal GPIO with 5V logic levels.
+|-
+| 6
+| DIO5
+| ENET2_TX_CLK
+| Default: ENET2 TX CLK line or universal GPIO with 5V logic levels.
+|-
+| 7
+| DIO6
+| UART1-RTS
+| Default: UART1 RTS line or universal GPIO with 5V logic levels.
+|-
+| 8
+| DIO7
+| UART1-CTS
+| Default: UART1 CTS line or universal GPIO with 5V logic levels.
+|-
+| colspan="4" | Digital I/Os connector J502, yellow connector
+|-
+| 1
+| DIO8
+| ENET2_TXD0
+| Default: ENET2 TXD0 line or universal GPIO with 5V logic levels.
+|-
+| 2
+| DIO9
+| ENET2_CRS_DV
+| Default: ENET2 CRS DV line or universal GPIO with 5V logic levels.
+|-
+| 3
+| DIO10
+| UART2-TXD
+| Default: UART2 TXD line or universal GPIO with 5V logic levels.
+|-
+| 4
+| DIO11
+| UART2-CTS
+| Default: UART2 CTS line or universal GPIO with 5V logic levels.
+|-
+| 5
+| DIO12
+| UART2-RTS
+| Default: UART2 RTS line or universal GPIO with 5V logic levels.
+|-
+| 6
+| DIO13
+| UART2-RXD
+| Default: UART2 RXD line or universal GPIO with 5V logic levels.
+|-
+| 7
+| GND
+| GND
+| -
+|-
+| 8
+| AREF
+| VCC-3V3
+| +3.3V generated by internal SOM LDO converter (limited load current).
+|-
+| 9
+| DIO14-SCL
+| UART5-RXD
+| Default: UART5 RXD line or universal GPIO with 5V logic levels.
+|-
+| 10
+| DIO15-SDA
+| UART5-TXD
+| Default: UART5 TXD line or universal GPIO with 5V logic levels.
+|}
+Notes:<br />
+. All I/O lines are 5V compatible.<br />
+. RESET line is 5V compatible.<br />
+. Preferred voltage range on AIN0…AIN3 lines is 0…+3.3V.<br />
+. Voltage level compatibility can be changed to +3.3V with removing R901 and mouting R902 (0R), but voltage range on AIN0…AIN3 lines must be 0…+3.3V.<br />
+== User LEDs connections ==
+[[File:VisionCB-RT-STD-1-0-led.png|center|600px]]
+{| class="wikitable"
+! style="text-align: center; font-weight: bold;" | LED
+! style="text-align: center; font-weight: bold;" | PCB symbol
+! style="text-align: center; font-weight: bold;" | GPIO
+! style="text-align: center; font-weight: bold;" | Description
+|-
+| D400/blue
+| GPIO10
+| GPIO1_10
+| Default: JTAG MOD input or universal GPIO with 3.3V logic levels.
+|-
+| D401/green
+| GPIO11
+| GPIO1_11
+| Default: JTAG TMS input or universal GPIO with 3.3V logic levels.
+|-
+| D403/yellow
+| GPIO12
+| GPIO1_12
+| Default: JTAG TDO input or universal GPIO with 3.3V logic levels.
+|-
+| D402/red
+| GPIO13
+| GPIO1_13
+| Default: JTAG TDI input or universal GPIO with 3.3V logic levels.
+|}
+Notes:<br />
+. LEDs are switched on by logic „1” set at the GPIO outputs.<br />
+. LEDs are controlled by current drivers and do not load the GPIOs.<br />
+== User switches connections ==
+[[File:VisionCB-RT-STD-1-0-switche.png|center|600px]]
+{| class="wikitable"
+! style="text-align: center; font-weight: bold;" | Switch
+! style="text-align: center; font-weight: bold;" | PCB symbol
+! style="text-align: center; font-weight: bold;" | GPIO
+! style="text-align: center; font-weight: bold;" | Description
+|-
+| S402
+| GPIO3
+| GPIO1_IO03
+| Universal GPIO with 3.3V logic levels.
+|-
+| S403
+| GPIO4
+| GPIO1_IO04
+| Universal GPIO with 3.3V logic levels.
+|-
+| S404
+| GPIO8
+| GPIO1_IO08
+| Universal GPIO with 3.3V logic levels.
+|-
+| S405
+| GPIO9
+| GPIO1_IO09
+| Universal GPIO with 3.3V logic levels.
+|}
+Notes:<br />
+. After button pressing on GPIO lines are set to „0”.<br />
+. GPIO lines connected to switches are separated from board’s environment by 1k resistors.<br />
+== TFT LCD connector (RGB 24b, J405) ==
+[[File:VisionCB-RT-STD-1-0-lcd.png|center|600px]]
+{| class="wikitable"
+! style="text-align: center; font-weight: bold;" | J405 pin
+! style="text-align: center; font-weight: bold;" | Default function name
+! style="text-align: center; font-weight: bold;" | LCD interface name
+|-
+| 1
+| LCD-DATA0
+| LCD-B0
+|-
+| 2
+| LCD-DATA1
+| LCD-B1
+|-
+| 3
+| LCD-DATA2
+| LCD-B2
+|-
+| 4
+| LCD-DATA3
+| LCD-B3
+|-
+| 5
+| LCD-DATA4
+| LCD-B4
+|-
+| 6
+| LCD-DATA5
+| LCD-B5
+|-
+| 7
+| LCD-DATA6
+| LCD-B6
+|-
+| 8
+| LCD-DATA7
+| LCD-B7
+|-
+| 9
+| GND
+| GND
+|-
+| 10
+| LCD-DATA8
+| LCD-G0
+|-
+| 11
+| LCD-DATA9
+| LCD-G1
+|-
+| 12
+| LCD-DATA10
+| LCD-G2
+|-
+| 13
+| LCD-DATA11
+| LCD-G3
+|-
+| 14
+| LCD-DATA12
+| LCD-G4
+|-
+| 15
+| LCD-DATA13
+| LCD-G5
+|-
+| 16
+| LCD-DATA14
+| LCD-G6
+|-
+| 17
+| LCD-DATA15
+| LCD-G7
+|-
+| 18
+| GND
+| GND
+|-
+| 19
+| LCD-DATA16
+| LCD-R0
+|-
+| 20
+| LCD-DATA17
+| LCD-R1
+|-
+| 21
+| LCD-DATA18
+| LCD-R2
+|-
+| 22
+| LCD-DATA19
+| LCD-R3
+|-
+| 23
+| LCD-DATA20
+| LCD-R4
+|-
+| 24
+| LCD-DATA21
+| LCD-R5
+|-
+| 25
+| LCD-DATA22
+| LCD-R6
+|-
+| 26
+| LCD-DATA23
+| LCD-R7
+|-
+| 27
+| GND
+| GND
+|-
+| 28
+| LCD-DE
+| DE
+|-
+| 29
+| LCD-HSYNC
+| HSYNC
+|-
+| 30
+| LCD-VSYNC
+| VSYNC
+|-
+| 31
+| GND
+| GND
+|-
+| 32
+| LCD-PCLK
+| DCLK
+|-
+| 33
+| GND
+| GND
+|-
+| 34
+| GPIO4
+| TS-YPUL
+|-
+| 35
+| GPIO3
+| TS-YNUR
+|-
+| 36
+| GPIO2
+| TS-YPLL
+|-
+| 37
+| GPIO1
+| TS-YNLR
+|-
+| 38
+| -
+| -
+|-
+| 39
+| -
+| -
+|-
+| 40
+| -
+| -
+|-
+| 41
+| -
+| -
+|-
+| 42
+| UART5-TXD
+| I2C-SCL
+|-
+| 43
+| UART5-RXD
+| I2C-SDA
+|-
+| 44
+| GND
+| GND
+|-
+| 45
+| VCC-LCD
+| +3.3V (controlled by ENET2_TXEN)
+|-
+| 46
+| VCC-LCD
+| +3.3V (controlled by ENET2_TXEN)
+|-
+| 47
+| VCC-5V0
+| +5.0V
+|-
+| 48
+| VCC-5V0
+| +5.0V
+|-
+| 49
+| LCD-RESET
+| RESET
+|-
+| 50
+| JTAG-nTRST
+| PWREN
+|}
+== Dimensions ==
+[[File:VisionCB-RT-STD-1-0-PCB-size.png|800px|center]]
 == Arduino compatible I/O headers (J500-J503) ==

	This page was last edited on 12 September 2019, at 09:27. Privacy policy About SomLabs Wiki
	Mozilla Cavendish skin modified by DaSch for the Web Community Wiki GitHub project page – Report a bug – Skin version: 3.0.0