StarSOM-6ULL Datasheet and Pinout: Difference between revisions
From SomLabs Wiki
| Line 291: | Line 291: | ||
[[StarSOM-6ULL- | [[StarSOM-6ULL-connectors.png|center]] | ||
Revision as of 13:00, 29 June 2022
StarSOM-6ULL Datasheet and Pinout
General description
The StarSOM-6ULL family is a SODIMM-sized SoM based on the NXP i.MX6 ULL application processor which features an advanced implementation of a single ARM Cortex-A7 core (at speeds up to 900MHz).
The StarSOM-6ULL is a low power highly integrated SoM (System on Module) featuring high computation power and 802.11b/g/n Wi-Fi and Bluetooth v5.1 connectivity. The option of integrated, fully certified Wi-Fi and Bluetooth module simplifies the carrier board design and is ideally suited for wireless application. The StarSOM-6ULL provides a variety memory configuration including flexible range of DDR3L, NAND, eMMC and SD memory card that meets our customers requirements.
The SoM supports connections to a variety of interfaces: two high-speed USB on-the-go with PHY, dual Ethernet, audio, display with touch panel and serial interfaces. In addition, the system supports industrial grade targeting embedded application.
SOMLabs also provides a complete hardware and software development board for the SoM in the form of a carrier board and optional TFT display and touch panel.
Applications
- Industrial embedded Linux computer
- Home Appliances
- Home Automation – Smart Home
- Human-machine Interfaces (HMI)
- Point-of-sales (POS) terminals
- Cash Register
- 2D barcode scanners and printers
- Smart grid infrastructure
- IoT gateways
- Residential gateways
- Machine vision equipment
- Robotics
- Fitness/outdoor equipment
Features
- Powered by NXP i.MX 6ULL application processor
- Core clock up to 900MHz
- Up to 512MB SDRAM DDR3L
- Up to 512MB NAND Flash / 32GB eMMC / uSD memory card
- Optional Murata 802.11b/g/n Wi-Fi and Bluetooth v5.2 module
- Power-efficient and cost-optimized solution
- Ideal for industrial IoT and embedded applications
- Integrated security features
Pictures of SOM versions
| Version | Photo |
|---|---|
| eMMC |
 |
| micro-SD |
 |
| NAND Flash |
 |
| Wi-Fi is available for all memory variants configurations. |
Ordering info
Json data error!
Block Diagram
Operating ranges
| Parameter | Value | Unit | Comment |
|---|---|---|---|
| Power Supply | Connected to +5VIN SODIMM pin | ||
| Input GPIO voltage | - | ||
| Environment temperature1 | oC | Industrial range w/o WiFi module | |
| Industrial range with WiFi module | |||
| Consumer range |
Note:
1. Maximum MPU junction temperature is +105oC (industrial version) or +95oC (consumer version).
Electrical parameters
| SOM signal name |
Parameter | Value | Units | ||
|---|---|---|---|---|---|
| Min. | Typ. | Max. | |||
| +5VIN | Supply Voltage | 4.0 | 5.0 | 5.5 | V |
| +5VIN | Total Supply Current1 | - | 115 | 155 | mA |
| VGPIO | GPIO Input Voltage | 0 | 3.3 | 3.62 | V |
| +3.3VOUT | SOM Internal LDO Output Current |
- | - | 0.5 | A |
| USB-OTGx-VBUS | USB Supply | 4.40 | - | 5.5 | V |
| VDD-COIN-3V | SNVS Backup Battery Supply |
2.66 | - | 3.6 | V |
| - | ADC Inputs Voltage | 0 | - | 3.3 | V |
Notes:
1. Excluding external load connected to +3.3VOUT lines.
2. Applying the maximum voltage 3.6V results in shorten lifetime. Recommended value is smaller than 3.5V.
SOM pinout
Important notes
1. Detail pin configurations description you can find, edit and arrange in dedicated MEX files (with free "i.MX Pin Tool" configurational tool):
VisionSOM-6ULL without WiFi module and no SDIO1 on edge connector or
VisionSOM-6ULL without WiFi module and with SDIO1 on edge connector or
VisionSOM-6ULL witht WiFi module on-board.
2. LCD_DATAxx pins are internally used for boot sequence configuration. We recommend to use LCD_DATAxx lines as outputs or using eFuse boot configuration.
| SoM pin number | Default function | GPIO | BGA289 ball | Notes |
|---|---|---|---|---|
| 1 | GND | - | - | |
| 2 | GND | - | - | |
| 26 | LCD.RES | GPIO3.04 | E9 | |
| 28 | I2C2.SDA | GPIO1.31 | G13 | Internally pull-uped with 4.7k connected to 3.3V |
| 30 | I2C2.SCL | GPIO1.30 | F17 | Internally pull-uped with 4.7k connected to 3.3V |
| 32 | GPIO1.01 | GPIO1.01 | L15 | |
| 34 | GPIO1.02 | GPIO1.02 | L14 | |
| 36 | GPIO1.03 | GPIO1.03 | L17 | |
| 38 | GPIO1.04 | GPIO1.04 | M16 | |
| 39 | GND | - | - | |
| 40 | GND | - | - | |
| 41 | VDD.EMMC | - | - | Internal 1.8V LDO output as reference or power supply voltage for QSPI (SDIO) interface |
| 42 | LCD.CLK | GPIO3.00 | A8 | |
| 43 | QSPI.CLK | GPIO4.11 | D5 | Line referenced to VDD.EMMC power supply (1.8V) |
| 44 | GND | - | - | |
| 45 | QSPI.CS0 | GPIO4.16 | E6 | Line referenced to VDD.EMMC power supply (1.8V) |
| 46 | LCD.VSYNC | GPIO3.03 | C9 | |
| 47 | QSPI.D0 | GPIO4.12 | A3 | Line referenced to VDD.EMMC power supply (1.8V) |
| 48 | LCD.HSYNC | GPIO3.02 | D9 | |
| 49 | QSPI.D1 | GPIO4.13 | C5 | Line referenced to VDD.EMMC power supply (1.8V) |
| 50 | LCD.ENABLE | GPIO3.01 | B8 | |
| 51 | QSPI.D2 | GPIO4.14 | B5 | Line referenced to VDD.EMMC power supply (1.8V) |
| 52 | LCD.DATA23 | GPIO3.28 | B16 | |
| 53 | QSPI.D3 | GPIO4.15 | A4 | Line referenced to VDD.EMMC power supply (1.8V) |
| 54 | LCD.DATA22 | GPIO3.27 | A14 | |
| 55 | QSPI.DQS | GPIO4.10 | B4 | Line referenced to VDD.EMMC power supply (1.8V) |
| 56 | LCD.DATA21 | GPIO3.26 | B14 | |
| 57 | GND | - | - | |
| 58 | LCD.DATA20 | GPIO3.25 | C14 | |
| 59 | BT.PCMCLK | GPIO4.26 | D3 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 60 | LCD.DATA19 | GPIO3.24 | D14 | |
| 61 | BT.PCMOUT | GPIO4.27 | D2 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 62 | LCD.DATA18 | GPIO3.23 | A13 | |
| 63 | BT.PCMIN | GPIO4.28 | D1 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 64 | LCD.DATA17 | GPIO3.22 | B13 | |
| 65 | BT.PCMSYNC | GPIO4.25 | D4 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 66 | LCD.DATA16 | GPIO3.21 | C13 | |
| 67 | BT.RTS | GPIO4.23 | E2 | BT-BLE interface connection - UART5 (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 68 | LCD.DATA15 | GPIO3.20 | D13 | |
| 69 | BT.CTS | GPIO4.24 | E1 | BT-BLE interface connection - UART5 (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 70 | LCD.DATA14 | GPIO3.19 | A12 | |
| 71 | BT.TXD | GPIO4.22 | E3 | BT-BLE interface connection - UART5 (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 72 | LCD.DATA13 | GPIO3.18 | B12 | |
| 73 | BT.RXD | GPIO4.21 | E4 | BT-BLE interface connection - UART5 (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 74 | LCD.DATA12 | GPIO3.17 | C12 | |
| 75 | BT.WAKE | GPIO4.20 | F3 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 76 | LCD.DATA11 | GPIO3.16 | D12 | |
| 77 | BT.HWAKE | GPIO4.19 | F2 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 78 | LCD.DATA10 | GPIO3.15 | E12 | |
| 79 | BT.ENABLE | GPIO4.17 | F5 | BT-BLE interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 80 | LCD.DATA09 | GPIO3.14 | A11 | |
| 81 | WLAN.HWAKE | GPIO4.18 | E5 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 82 | LCD.DATA08 | GPIO3.13 | B11 | |
| 83 | WLAN.EN | GPIO1.08 | N17 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 84 | LCD.DATA07 | GPIO3.12 | D11 | |
| 85 | GND | - | - | |
| 86 | LCD.DATA06 | GPIO3.11 | A10 | |
| 87 | SDIO1.CLK | GPIO2.17 | C1 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 88 | LCD.DATA05 | GPIO3.10 | B10 | |
| 89 | SDIO1.CMD | GPIO2.16 | C2 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 90 | LCD.DATA04 | GPIO3.09 | C10 | |
| 91 | SDIO1.D2 | GPIO2.20 | B1 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 92 | LCD.DATA03 | GPIO3.08 | D10 | |
| 93 | SDIO1.D0 | GPIO2.18 | B3 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 94 | LCD.DATA02 | GPIO3.07 | E10 | |
| 95 | SDIO1.D3 | GPIO2.21 | A2 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 96 | LCD.DATA01 | GPIO3.06 | A9 | |
| 97 | SDIO1.D1 | GPIO2.19 | B2 | WiFi interface connection (if 1DX modules used) If 1DX modules is not used alternative pin functions (incl. GPIO) available |
| 98 | LCD.DATA00 | GPIO3.05 | B9 | |
| 99 | GND | - | - | |
| 100 | GND | - | - | |
| 1 | +3V3IN | - | - | External power supply 3.3V |
| 2 | +3V3IN | - | - | External power supply 3.3V |
| 3 | +3V3IN | - | - | External power supply 3.3V |
| 4 | +3V3IN | - | - | External power supply 3.3V |
| 5 | +3V3IN | - | - | External power supply 3.3V |
| 6 | +3V3IN | - | - | External power supply 3.3V |
| 7 | +3V3IN | - | - | External power supply 3.3V |
| 8 | +3V3IN | - | - | External power supply 3.3V |
| 9 | +3V3IN | - | - | External power supply 3.3V |
| 10 | +3V3IN | - | - | External power supply 3.3V |
| 11 | GND | - | - | |
| 12 | GND | - | - | |
| 13 | GND | - | - | |
| 14 | GND | - | - | |
| 15 | GND | - | - | |
| 16 | GND | - | - | |
| 17 | PMIC-ON-REQ | |||
| 18 | ON-OFF | ON-OFF | R8 | |
| 19 | PMIC-STBY-REQ | PMIC-STBY-REQ | U9 | |
| 20 | POR | POR | P8 | Power-on-reset input-output |
| 21 | VDD-3V3-SNVS | VDD-SNVS-IN | P12 | SNVS domain power supply External 3.3V connection power supply is necessary |
| 22 | RECOVERY | System recovery pin: RECOVERY=0 during reset -> start recovery mode RECOVERY=1 or not connected -> normal operation mode | ||
| 23 | GND | - | - | |
| 24 | RESET.IN | - | - | System reset |
| 25 | UART4.RXD | GPIO1.29 | G16 | Default Linux console RxD line |
| 26 | GND | - | - | |
| 27 | UART4.TXD | GPIO1.28 | G17 | Default Linux console TxD line |
| 28 | TAMPER.0 | GPIO5.00 | R10 | |
| 29 | +3V3SW | - | - | Reference 3.3V power supply for external peripherals, maximum load 200 mA |
| 30 | TAMPER.1 | GPIO5.01 | R9 | |
| 32 | TAMPER.2 | GPIO5.02 | P11 | |
| 34 | TAMPER.3 | GPIO5.03 | P10 | |
| 36 | TAMPER.4 | GPIO5.04 | P9 | |
| 37 | GND | - | - | |
| 38 | TAMPER.5 | GPIO5.05 | N8 | |
| 39 | USB2.VBUS | U12 | ||
| 40 | TAMPER.6 | GPIO5.06 | N11 | |
| 41 | USB2.DN | - | T13 | |
| 42 | TAMPER.7 | GPIO5.07 | N10 | |
| 43 | USB2.DP | - | U13 | |
| 44 | TAMPER.8 | GPIO5.08 | N9 | |
| 45 | GND | - | - | |
| 46 | TAMPER.9 | GPIO5.09 | R6 | |
| 47 | GPIO1.05 | GPIO1.05 | M17 | |
| 48 | GND | - | - | |
| 49 | USB1.VBUS | - | T12 | |
| 50 | JTAG.TCK | GPIO1.14 | M14 | Optionally used as 32kHz clock source for 1DX radio module |
| 51 | USB1.DN | - | T15 | |
| 52 | JTAG.TDI | GPIO1.13 | N16 | |
| 53 | USB1.DP | - | U15 | |
| 54 | JTAG.TDO | GPIO1.12 | N15 | |
| 55 | GND | - | - | |
| 56 | JTAG.TMS | GPIO1.11 | P14 | |
| 57 | USB1.ID | GPIO1.00 | K13 | |
| 58 | JTAG.TRST | GPIO1.15 | N14 | |
| 60 | GND | - | - | |
| 62 | UART1.CTS | GPIO1.18 | K15 | |
| 63 | GND | - | - | |
| 64 | UART1.RTS | GPIO1.19 | J14 | |
| 65 | ENET2.TX-CLK | GPIO2.14 | D17 | |
| 66 | UART1.RXD | GPIO1.17 | K16 | |
| 67 | ENET2.TXD1 | GPIO2.12 | A16 | |
| 68 | UART1.TXD | GPIO1.16 | K14 | |
| 69 | ENET2.TXD0 | GPIO2.11 | A15 | |
| 70 | UART2.CTS | GPIO1.22 | J15 | |
| 71 | ENET2.TXEN | GPIO2.13 | B15 | |
| 72 | UART2.RTS | GPIO1.23 | H14 | |
| 73 | ENET2.RXER | GPIO2.15 | D16 | |
| 74 | UART2.RXD | GPIO1.21 | J16 | |
| 75 | ENET2.RXEN | GPIO2.10 | B17 | |
| 76 | UART2.TXD | GPIO1.20 | J17 | |
| 77 | ENET2.RXD0 | GPIO2.08 | C17 | |
| 78 | UART3.CTS | GPIO1.26 | H15 | |
| 79 | ENET2.RXD1 | GPIO2.09 | C16 | |
| 80 | UART3.RTS | GPIO1.27 | G14 | |
| 81 | ENET.MDC | GPIO1.07 | L16 | |
| 82 | UART3.RXD | GPIO1.25 | H16 | |
| 83 | ENET.MDIO | GPIO1.06 | K17 | |
| 84 | UART3.TXD | GPIO1.24 | H17 | |
| 85 | GND | - | - | |
| 86 | GND | - | - | |
| 87 | ENET1.LED0 | - | - | LED0/nWAYEN - output PHY signal (LED cathode) |
| 89 | ENET1.LED1 | - | - | LED0/SPEED - output PHY signal (LED cathode) |
| 91 | ENET1.RXN | - | - | Rx_n - external Ethernet trafo connector |
| 93 | ENET1.RXP | - | - | Rx_p - external Ethernet trafo connector |
| 95 | ENET1.TXN | - | - | Tx_n - external Ethernet trafo connector |
| 97 | ENET1.TXP | - | - | Tx_p - external Ethernet trafo connector |
| 99 | GND | - | - | |
| 100 | GND | - | - | |
| - | JTAG.MOD | GPIO1.10 | P15 | Used as hardware reset Ethernet PHY with 4.7k pull-down resistor |
| - | BOOT.MODE1 | - | U10 | Permanently connected to GND |
