Difference between revisions of "SL-TFT7-TP-800-480 Datasheet and Pinout"
From SomLabs Wiki
(→Pictures of SL-TFT7-TP-800-480 module) |
|||
Line 19: | Line 19: | ||
== Pictures of SL-TFT7-TP-800-480 module == | == Pictures of SL-TFT7-TP-800-480 module == | ||
− | [[File:Example.jpg]] | + | [[File:Example.jpg]]<br> |
[[File:Example.jpg]] | [[File:Example.jpg]] | ||
Revision as of 09:54, 27 April 2018
VisionSOM-6ULL Datasheet and Pinout
Contents
General description
SL-TFT7-TP-800-480 is complete display TFT-LCD (800x480 px) module integrated with capactive touch-panel. Module is powered from +5V @400mA, data interface is 24 b parallel RGB + I2C (touch-panel controller). SL-TFT7-TP-800-480 module is equpiied with FPC50 connector, 1:1 compatible with SoMLabs carrier, eval and base boards.
SOMLabs also provides a complete hardware and software development board for the SoM in the form of a carrier board and optional TFT display and touch panel.
Features
- Powered by Powertip PH800480T013-IBC06 LCD-TFT
- Display size 7 inches
- Display LCD matrix 800x480 px
- Capacitive touch-panel + TP controller
- 24-b RGB parallel interface
- Single supply +5V (DC/DC converters built-in)
- Backlight LEDs built-in
- Fully compatible with SoMLabs carrier, eval and base boards
Pictures of SL-TFT7-TP-800-480 module
Ordering info
SLS | Product type SLS - System on Module |
N | SOM Name 1 - VisionSOM SODIMM200 |
6 | CPU Family 6 - i.MX6 |
CpuType | CPU Type Y0 - i.MX6 ULL Y0 Y1 - i.MX6 ULL Y1 Y2 - i.MX6 ULL Y2 |
Clock | CPU Clock Speed 528C - 528MHz 792C - 792MHz 900C - 900MHz |
RamSize | DDR3 RAM Size 64R - 64MB 128R - 128MB 256R - 256MB 512R - 512MB |
FlashSize | Flash Size Type and Density SD - MicroSD connector 128N - 128MB NAND 256N - 256MB NAND 512N - 512MB NAND 04GE - 4GB eMMC 08GE - 8GB eMMC 16GE - 16GB eMMC 32GE - 32GB eMMC |
SF | Special Features 0SF - No Special Features 1WB - Built-in 802.11b/g/n Wi-Fi and Bluetooth v4.1+EDR Module |
TEMP | Operating Temperature C - Consumer: 0 to +70 C SI - Industrial with Wi-Fi: -30 to +70 C I - Industrial: -40 to +85 C |
V | SOM Version A - Version 1.0 B - Version 1.1 |
Block Diagram
Operating ranges
Parameter | Value | Unit | Comment |
---|---|---|---|
Power Supply | |
|
Connected to +5VIN SODIMM pin |
Input GPIO voltage | |
|
- |
Environment temperature1 | |
oC | Industrial range w/o WiFi module |
|
Industrial range with WiFi module | ||
|
Consumer range |
Note:
1. Maximum MPU junction temperature is +105oC (industrial version) or +95oC (consumer version).
Electrical parameters
SOM signal name |
Parameter | Value | Units | ||
---|---|---|---|---|---|
Min. | Typ. | Max. | |||
+5VIN | Supply Voltage | 4.0 | 5.0 | 5.5 | V |
- | Total Supply Current1 | x | x | x | A |
VGPIO | GPIO Input Voltage | 0 | 3.3 | 3.62 | V |
+3.3VOUT | SOM Internal LDO Output Current |
- | - | 0.5 | A |
USB-OTGx-VBUS | USB Supply | 4.40 | - | 5.5 | V |
VDD-COIN-3V | SNVS Backup Battery Supply |
2.66 | - | 3.6 | V |
- | ADC Inputs Voltage | 0 | - | 3.3 | V |
Notes:
1. Excluding external load connected to +3.3VOUT lines.
2. Applying the maximum voltage 3.6V results in shorten lifetime. Recommended value is smaller than 3.5V.
SOM pinout
SODIMM PIN | Functional
domain |
Function name | i.MX6 UltraLite/
ULL Pad Name |
Alternate functions | Description (refer to i.MX6 UltraLite/ULL manuals for details) |
---|---|---|---|---|---|
1 | Power | GND | - | - | - |
2 | Power | GND | - | - | - |
3 | Ctrl | PMIC-STBY-REQ | CCM_PMIC_STBY_REQ | - | Output, leave open if not used. |
4 | Ctrl | MX6-POR-B | - | - | External warm reset input, active L. |
5 | Ctrl | PMIC-ON-REQ | SNVS_PMIC_ON_REQ | - | Output, leave open if not used. |
6 | Power | VDD-SNVS-3V3 | VDD_SNVS_IN | - | SNVS backup power supply must be held between 2.9V and 3.3V if the system requires keeping real time and other data on OFF state. Internally connected to +3.3V, leave open. |
7 | BOOT | BOOT-MODE1 | BOOT_MODE1 | GPIO5_IO11 | BOOT-MODE1 BOOT-MODE0
00 boot from fuses (default) 01 serial downloader 10 internal boot 11 reserved |
8 | Power | VDD-COIN-3V | VDD_SNVS_IN | - | Optional external coin battery for SNVS power domain, must be held between 2.9V and 3.3V if the system requires keeping real time and other data on OFF state.
Leave open if not used. |
9 | BOOT | BOOT-MODE0 | BOOT_MODE0 | GPIO5_IO10 | BOOT-MODE1 BOOT-MODE0
00 boot from fuses (default) 01 serial downloader 10 internal boot 11 reserved |
10 | GPIO-SNVS | SNVS-TAMPER9 | SNVS_TAMPER9 | GPIO5_IO09 | Tamper input (SNVS power domain) or GPIO 3.3V. |
11 | USB | USB-OTG2-VBUS | USB_OTG2_VBUS | - | +5V USB bus. Leave open if not used. |
12 | GPIO-SNVS | SNVS-TAMPER5 | SNVS_TAMPER5 | GPIO5_IO05 | Tamper input (SNVS power domain) or GPIO 3.3V. |
13 | USB | USB-OTG1-VBUS | USB_OTG1_VBUS | - | +5V USB bus. Leave open if not used. |
14 | Ctrl | ONOFF | SRC_RESET_B | Input for power interrupt generation. Leave open if not used. | |
15 | Power | GND | - | - | - |
16 | Ctrl | POR-B | POR_B | - | Cold reset negative logic input resets all modules and logic in the IC.
May be used in addition to internally generated power on reset signal (logical AND, both internal and external signals are considered active low). |
17 | Power | GND | - | - | - |
18 | GPIO-SNVS | SNVS-TAMPER8 | SNVS_TAMPER8 | GPIO5_IO08 | Tamper input (SNVS power domain) or GPIO 3.3V. |
19 | USB | USB-OTG2-DP | USB_OTG2_DP | - | Leave open if not used. |
20 | Power | GND | - | - | - |
21 | USB | USB-OTG2-DN | USB_OTG2_DN | - | Leave open if not used. |
22 | Power | GND | - | - | - |
23 | Power | GND | - | - | - |
24 | GPIO-SNVS | SNVS-TAMPER7 | SNVS_TAMPER7 | GPIO5_IO07 | Tamper input (SNVS power domain) or GPIO 3.3V. |
25 | USB | USB-OTG1-DP | USB_OTG1_DP | - | Leave open if not used. |
26 | Power | GND | - | - | - |
27 | USB | USB-OTG1-DN | USB_OTG1_DN | - | Leave open if not used. |
28 | Power | GND | - | - | - |
29 | Power | GND | - | - | - |
30 | GPIO-SNVS | SNVS-TAMPER4 | SNVS_TAMPER4 | GPIO5_IO04 | Tamper input (SNVS power domain) or GPIO 3.3V. |
31 | USB | nUSB-OTG-CHD | USB_OTG1_CHD_B | - | Leave open if not used. |
32 | GPIO-SNVS | SNVS-TAMPER1 | SNVS_TAMPER1 | GPIO5_IO01 | Tamper input (SNVS power domain) or GPIO 3.3V. |
33 | JTAG | JTAG-MOD | JTAG_MOD | - | Leave open if not used. |
34 | GPIO-SNVS | SNVS-TAMPER3 | SNVS_TAMPER3 | GPIO5_IO03 | Tamper input (SNVS power domain) or GPIO 3.3V. |
35 | Power | GND | - | - | - |
36 | GPIO-SNVS | SNVS-TAMPER0 | SNVS_TAMPER0 | GPIO5_IO00 | Tamper input (SNVS power domain) or GPIO 3.3V. |
37 | CLK1-N | CCM_CLK1_N | - | General purpose differential high speed clock input/output.
Leave open if not used. | |
38 | Power | GND | - | - | - |
39 | CLK1-P | CCM_CLK1_P | - | General purpose differential high speed clock input/output.
Leave open if not used. | |
40 | Power | GND | - | - | - |
41 | Power | GND | - | - | - |
42 | GPIO-SNVS | SNVS-TAMPER6 | SNVS_TAMPER6 | GPIO5_IO06 | Tamper input (SNVS power domain) or GPIO 3.3V. |
43 | JTAG | JTAG-TDI | JTAG_TDI | - | JTAG TDI input line. |
44 | GPIO-SNVS | SNVS-TAMPER2 | SNVS_TAMPER2 | GPIO5_IO02 | Tamper input (SNVS power domain) or GPIO 3.3V. |
45 | GPIO | GPIO-8 | GPIO1_IO08 | PWM1_OUT
WDOG1_WDOG_B SPDIF_OUT CSI_VSYNC USDHC2_VSELECT CCM_PMIC_RDY UART5_RTS_B |
Universal GPIO with 3.3V logic levels. |
46 | JTAG | JTAG-TMS | JTAG_TMS | - | JTAG TMS input line. |
47 | GPIO | GPIO-4 | GPIO1_IO04 | ENET1_REF_CLK1
PWM3_OUT USB_OTG1_PWR USDHC1_RESET_B ENET2_1588_EVENT0_IN UART5_TX |
Universal GPIO with 3.3V logic levels. |
48 | JTAG | JTAG-nTRST | JTAG_TRST_B | - | JTAG TRST input line (active L). |
49 | GPIO | GPIO-5 | GPIO1_IO05 | ENET2_REF_CLK2
PWM4_OUT ANATOP_OTG2_ID CSI_FIELD USDHC1_VSELECT ENET2_1588_EVENT0_OUT UART5_RX |
Universal GPIO with 3.3V logic levels.
WLAN-ENABLE in SOM with WiFi/BT module |
50 | Power | GND | - | - | - |
51 | Power | GND | - | - | - |
52 | JTAG | JTAG-TDO | JTAG_TDO | - | JTAG TDO output line. |
53 | GPIO | GPIO-7 | GPIO1_IO07 | NET1_MDC
ENET2_MDC USB_OTG_HOST_MODE CSI_PIXCLK USDHC2_CD_BCCM_STOP UART1_RTS_B |
Universal GPIO with 3.3V logic levels. |
54 | JTAG | JTAG-TCK | JTAG_TCK | - | JTAG TCK input line.
Connected to JTAG-TCK line (via separating resistor 10k). |
55 | GPIO | GPIO-3 | GPIO1_IO03 | I2C1_SDA
GPT1_COMPARE3 USB_OTG2_OC USDHC1_CD_B CCM_DI0_EXT_CLK SRC_TESTER_ACK |
Universal GPIO with 3.3V logic levels. |
56 | GPIO | GPIO-9 | GPIO1_IO09 | PWM2_OUT
WDOG1_WDOG_ANY SPDIF_IN CSI_HSYNC USDHC2_RESET_B USDHC1_RESET_B UART5_CTS_B |
Universal GPIO with 3.3V logic levels. |
57 | COM-GPIO | UART1-TXD | UART1_TX_DATA | ENET1_RDATA02
I2C3_SCL CSI_DATA02 GPT1_COMPARE1 GPIO1_IO16 SPDIF_OUT UART5_TX |
Default: UART1 TxD output or universal GPIO with 3.3V logic levels. |
58 | GPIO | GPIO-2 | GPIO1_IO02 | I2C1_SCL
GPT1_COMPARE2 USB_OTG2_PWR ENET1_REF_CLK_25M USDHC1_WPS DMA_EXT_EVENT00 SRC_ANY_PU_RESET UART1_TX |
Universal GPIO with 3.3V logic levels. |
59 | Power | GND | - | - | - |
60 | Power | GND | - | - | - |
61 | GPIO | GPIO-6 | GPIO1_IO06 | ENET1_MDIO
ENET2_MDIO USB_OTG_PWR_WAKE CSI_MCLK USDHC2_WPCCM_WAIT CCM_REF_EN_B UART1_CTS_B |
Universal GPIO with 3.3V logic levels. |
62 | GPIO | GPIO-1 | GPIO1_IO01 | I2C2_SDA
GPT1_COMPARE1 USB_OTG1_OC ENET2_REF_CLK2 MQS_LEFT ENET1_1588_EVENT0_OUT SRC_EARLY_RESET WDOG1_WDOG_B |
Universal GPIO with 3.3V logic levels. |
63 | COM-GPIO | UART1-RXD | UART1_RX_DATA | ENET1_RDATA03
I2C3_SDA CSI_DATA03 GPT1_CLK GPIO1_IO17 SPDIF_IN UART5_RX |
Default: UART1 RxD input or universal GPIO with 3.3V logic levels. |
64 | GPIO | GPIO-0 | GPIO1_IO00 | I2C2_SCL
GPT1_CAPTURE1 ANATOP_OTG1_ID ENET1_REF_CLK1 MQS_RIGHT ENET1_1588_EVENT0_IN SRC_SYSTEM_RESET WDOG3_WDOG_B |
Universal GPIO with 3.3V logic levels. |
65 | COM-GPIO | UART2-TXD | UART2_TX_DATA | ENET1_TDATA02
I2C4_SCL CSI_DATA06 GPT1_CAPTURE1 GPIO1_IO20 ECSPI3_SS0 |
Default: UART2 TxD output or universal GPIO with 3.3V logic levels. |
66 | COM-GPIO | UART1-CTS | UART1_CTS_B | ENET1_RX_CLK
USDHC1_WP CSI_DATA04 ENET2_1588_EVENT1_IN GPIO1_IO18 USDHC2_WP UART5_CTS_B |
Default: UART1 CTS output or universal GPIO with 3.3V logic levels. |
67 | COM-GPIO | UART2-RXD | UART2_RX_DATA | ENET1_TDATA03
I2C4_SDA CSI_DATA07 GPT1_CAPTURE2 GPIO1_IO21 SJC_DONE ECSPI3_SCLK |
Default: UART2 RxD input or universal GPIO with 3.3V logic levels. |
68 | COM-GPIO | UART5-RXD | UART5_RX_DATA | ENET2_COL
I2C2_SDA CSI_DATA15 CSU_CSU_INT_DEB GPIO1_IO31 ECSPI2_MISO EPDC_PWRCTRL03 |
Default: UART5 RxD input or universal GPIO with 3.3V logic levels. |
69 | COM-GPIO | UART3-TXD | UART3_TX_DATA | ENET2_RDATA02
CSI_DATA01 UART2_CTS_B GPIO1_IO24 SJC_JTAG_ACT |
Default: UART3 TxD input or universal GPIO with 3.3V logic levels. |
70 | Power | GND | - | - | - |
71 | Power | GND | - | - | - |
72 | COM-GPIO | UART2-CTS | UART2_CTS_B | ENET1_CRS
FLEXCAN2_TXCSI_DATA08 GPT1_COMPARE2 GPIO1_IO22 SJC_DE_B ECSPI3_MOSI |
Default: UART2 CTS output or universal GPIO with 3.3V logic levels. |
73 | COM-GPIO | UART3-RXD | UART3_RX_DATA | ENET2_RDATA03
CSI_DATA00 UART2_RTS_B GPIO1_IO25 EPIT1_OUT |
Default: UART3 RxD input or universal GPIO with 3.3V logic levels. |
74 | COM-GPIO | UART1-RTS | UART1_RTS_B | ENET1_TX_ER
USDHC1_CD_BCSI_DATA05 ENET2_1588_EVENT1_OUT GPIO1_IO19 USDHC2_CD_B UART5_RTS_B |
Default: UART1 RTS input or universal GPIO with 3.3V logic levels. |
75 | COM-GPIO | UART4-TXD | UART4_TX_DATA | ENET2_TDATA02
I2C1_SCL CSI_DATA12 CSU_CSU_ALARM_AUT02 GPIO1_IO28 ECSPI2_SCLK |
Default: UART4 TxD output or universal GPIO with 3.3V logic levels. |
76 | COM-GPIO | UART3-CTS | UART3_CTS_B | ENET2_RX_CLK
FLEXCAN1_TX CSI_DATA10 ENET1_1588_EVENT1_IN GPIO1_IO26 EPIT2_OUT |
Default: UART3 CTS output or universal GPIO with 3.3V logic levels. |
77 | COM-GPIO | UART4-RXD | UART4_RX_DATA | ENET2_TDATA03
I2C1_SDA CSI_DATA13 CSU_CSU_ALARM_AUT01 GPIO1_IO29 ECSPI2_SS0 EPDC_PWRCTRL01 |
Default: UART4 RxD input or universal GPIO with 3.3V logic levels. |
78 | COM-GPIO | UART2-RTS | UART2_RTS_B | ENET1_COL
FLEXCAN2_RX CSI_DATA09 GPT1_COMPARE3 GPIO1_IO23 SJC_FAIL ECSPI3_MISO |
Default: UART2 RTS input or universal GPIO with 3.3V logic levels. |
79 | COM-GPIO | UART5-TXD | UART5_TX_DATA | GPIO1_IO30
ECSPI2_MOSI EPDC_PWRCTRL02 ENET2_CRS I2C2_SCL CSI_DATA14 CSU_CSU_ALARM_AUT00 |
Default: UART5 TxD output or universal GPIO with 3.3V logic levels. |
80 | COM-GPIO | UART3-RTS | UART3_RTS_B | ENET2_TX_ER
FLEXCAN1_RX CSI_DATA11 ENET1_1588_EVENT1_OUT GPIO1_IO27 WDOG1_WDOG_B |
Default: UART3 RTS input or universal GPIO with 3.3V logic levels. |
81 | Power | GND | - | - | - |
82 | Power | GND | - | - | - |
83 | NC | - | - | - | - |
84 | Power | GND | - | - | - |
85 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
86 | NC | - | - | - | - |
87 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
88 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
89 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
90 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
91 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
92 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
93 | Power | +3.3VOUT | - | - | +3.3V generated by SOM's LDO. |
94 | NC | - | - | - | - |
95 | NC | - | - | - | - |
96 | Power | +5VIN | - | - | +4.0-5.5V input power supply. |
97 | Ethernet | ENET1-RXD0 | ENET1_RX_DATA0 | UART4_RTS_B
PWM1_OUT CSI_DATA16 FLEXCAN1_TX GPIO2_IO00 KPP_ROW00 USDHC1_LCTL EPDC_SDCE04 |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
98 | Power | +5VIN | - | - | +4.0-5.5V input power supply. |
99 | Ethernet | ENET1-RXD1 | ENET1_RX_DATA1 | UART4_CTS_B
PWM2_OUT CSI_DATA17 FLEXCAN1_RX GPIO2_IO01 KPP_COL00 USDHC2_LCTL EPDC_SDCE05 |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
100 | Power | +5VIN | - | - | +4.0-5.5V input power supply. |
101 | Ethernet | ENET1-CRS-DV | ENET1_RX_EN | UART5_RTS_B
CSI_DATA18 FLEXCAN2_TX GPIO2_IO02 KPP_ROW01 USDHC1_VSELECT EPDC_SDCE06 |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
102 | Power | +5VIN | +4.0-5.5V input power supply. | ||
103 | Power | GND | - | - | - |
104 | Power | +5VIN | +4.0-5.5V input power supply. | ||
105 | Ethernet | ENET2-TX-CLK | ENET2_TX_CLK | UART8_CTS_B
ECSPI4_MISO ENET2_REF_CLK2 GPIO2_IO14 KPP_ROW07 ANATOP_OTG2_ID EPDC_SDDO14 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
10R resistor connected in series. |
106 | Power | +5VIN | +4.0-5.5V input power supply. | ||
107 | Power | GND | - | - | - |
108 | Power | +5VIN | +4.0-5.5V input power supply. | ||
109 | Ethernet | ENET2-RXER | ENET2_RX_ER | UART8_RTS_B
ECSPI4_SS0 EIM_ADDR25 GPIO2_IO15 KPP_COL07 WDOG1_WDOG_ANY EPDC_SDDO15 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels.
Connected to WD_G-B line. |
110 | Power | +5VIN | - | - | +4.0-5.5V input power supply. |
111 | Ethernet | ENET2-RXD0 | ENET2_RX_DATA0 | UART6_TX
I2C3_SCL ENET1_MDIO GPIO2_IO08 KPP_ROW04 USB_OTG1_PWR EPDC_SDDO08 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels. |
112 | Power | +5VIN | - | - | +4.0-5.5V input power supply. |
113 | Ethernet | ENET2-RXD1 | ENET2_RX_DATA1 | UART6_RX
I2C3_SDA ENET1_MDC GPIO2_IO09 KPP_COL04 USB_OTG1_OCE PDC_SDDO09 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels. |
114 | Ethernet | ENET1-TXEN | ENET1_TX_EN | UART6_RTS_B
PWM6_OUT CSI_DATA21 ENET2_MDC GPIO2_IO05 KPP_COL02 WDOG2_WDOG_RST_B_DEB EPDC_SDCE09 |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
115 | Power | GND | - | - | - |
116 | Power | GND | - | - | - |
117 | Ethernet | ENET2-CRS-DV | ENET2_RX_EN | UART7_TX
I2C4_SCL EIM_ADDR26 GPIO2_IO10 KPP_ROW05 ENET1_REF_CLK_25M EPDC_SDDO10 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels. |
118 | Ethernet | ENET1-TX-CLK | ENET1_TX_CLK | UART7_CTS_B
PWM7_OUT CSI_DATA22 ENET1_REF_CLK1 GPIO2_IO06 KPP_ROW03 GPT1_CLK EPDC_SDOED |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels.
10R resistor connected in series. |
119 | Ethernet | ENET2-TXD1 | ENET2_TX_DATA1 | UART8_TX
ECSPI4_SCLK EIM_EB_B03 GPIO2_IO12 KPP_ROW06 USB_OTG2_PWR EPDC_SDDO12 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels. |
120 | Power | GND | - | - | - |
121 | Ethernet | ENET2-TXEN | ENET2_TX_EN | UART8_RX
ECSPI4_MOSI EIM_ACLK_FREERUN GPIO2_IO13 KPP_COL06 USB_OTG2_OC EPDC_SDDO13 |
|
122 | Ethernet | ENET1-TXD0 | ENET1_TX_DATA0 | UART5_CTS_B
CSI_DATA19 FLEXCAN2_RX GPIO2_IO03 KPP_COL01 USDHC2_VSELECT EPDC_SDCE07 |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
123 | Ethernet | ENET2-TXD0 | ENET2_TX_DATA0 | UART7_RX
I2C4_SDA EIM_EB_B02 GPIO2_IO11 KPP_COL05 EPDC_SDDO11 |
Ethernet MAC2-PHY interface signal or universal GPIO with 3.3V logic levels. |
124 | Ethernet | ENET1-TXD1 | ENET1_TX_DATA1 | UART6_CTS_B
PWM5_OUT CSI_DATA20 ENET2_MDIO GPIO2_IO04 KPP_ROW02 WDOG1_WDOG_RST_B_DEB EPDC_SDCE08 |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
125 | Power | GND | - | - | - |
126 | Ethernet | ENET1-RXER | ENET1_RX_ER | UART7_RTS_B
PWM8_OUT CSI_DATA23 EIM_CRE GPIO2_IO07 KPP_COL03 GPT1_CAPTURE2 EPDC_SDOEZ |
Ethernet MAC1-PHY interface signal or universal GPIO with 3.3V logic levels. |
127 | Power | GND | - | - | - |
128 | Power | GND | - | - | - |
129 | LCD | LCD-DATA21 | LCD_DATA21 | UART8_RX
ECSPI1_SS0 CSI_DATA13 EIM_DATA13 GPIO3_IO26 SRC_BT_CFG29 USDHC2_DATA1 EPDC_SDCE01 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
130 | Power | GND | - | - | - |
131 | LCD | LCD-DATA22 | LCD_DATA22 | MQS_RIGHT
ECSPI1_MOSI CSI_DATA14 EIM_DATA14 GPIO3_IO27 SRC_BT_CFG30 USDHC2_DATA2 USDHC2_DATA2 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
132 | Power | GND | - | - | - |
133 | LCD | LCD-DATA17 | LCD_DATA17 | UART7_RX
CSI_DATA00 EIM_DATA09 GPIO3_IO22 SRC_BT_CFG25 USDHC2_DATA7 EPDC_GDSP |
LCD interface signal or universal GPIO with 3.3V logic levels. |
134 | LCD | LCD-DATA23 | LCD_DATA23 | MQS_LEFT
ECSPI1_MISO CSI_DATA15 EIM_DATA15 GPIO3_IO28 SRC_BT_CFG31 USDHC2_DATA3 EPDC_SDCE03 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
135 | Power | GND | - | - | - |
136 | Power | GND | - | - | - |
137 | LCD | LCD-DATA18 | LCD_DATA18 | PWM5_OUT
CA7_MX6ULL_EVENTO CSI_DATA10 EIM_DATA10 GPIO3_IO23 SRC_BT_CFG26 USDHC2_CMD EPDC_BDR01 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
138 | LCD | LCD-DATA19 | LCD_DATA19 | PWM6_OUT
WDOG1_WDOG_ANY CSI_DATA11 EIM_DATA11 GPIO3_IO24 SRC_BT_CFG27 USDHC2_CLK EPDC_VCOM00 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
139 | LCD | LCD-DATA13 | LCD_DATA13 | SAI3_TX_BCLK
CSI_DATA21 EIM_DATA05 GPIO3_IO18 SRC_BT_CFG13 USDHC2_RESET_B EPDC_BDR00 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
140 | LCD | LCD-DATA20 | LCD_DATA20 | UART8_TX
ECSPI1_SCLK CSI_DATA12 EIM_DATA12 GPIO3_IO25 SRC_BT_CFG28 USDHC2_DATA0 EPDC_VCOM01 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
141 | LCD | LCD-DATA14 | LCD_DATA14 | SAI3_RX_DATA
CSI_DATA22 EIM_DATA06 GPIO3_IO19 SRC_BT_CFG14 USDHC2_DATA4 EPDC_SDSHR |
LCD interface signal or universal GPIO with 3.3V logic levels. |
142 | LCD | LCD-DATA15 | LCD_DATA15 | SAI3_TX_DATA
CSI_DATA23 EIM_DATA07 GPIO3_IO20 SRC_BT_CFG15 USDHC2_DATA5 EPDC_GDRL |
LCD interface signal or universal GPIO with 3.3V logic levels. |
143 | LCD | LCD-DATA8 | LCD_DATA08 | SPDIF_IN
CSI_DATA16 EIM_DATA00 GPIO3_IO13 SRC_BT_CFG08 FLEXCAN1_TX EPDC_PWRIRQ |
LCD interface signal or universal GPIO with 3.3V logic levels. |
144 | LCD | LCD-DATA16 | LCD_DATA16 | UART7_TX
CSI_DATA01 EIM_DATA08 GPIO3_IO21 SRC_BT_CFG24 USDHC2_DATA6 EPDC_GDCLK |
LCD interface signal or universal GPIO with 3.3V logic levels. |
145 | LCD | LCD-DATA9 | LCD_DATA09 | SAI3_MCLK
CSI_DATA17 EIM_DATA01 GPIO3_IO14 SRC_BT_CFG09 FLEXCAN1_RX EPDC_PWRWAKE |
LCD interface signal or universal GPIO with 3.3V logic levels. |
146 | Power | GND | - | - | - |
147 | Power | GND | - | - | - |
148 | LCD | LCD-DATA11 | LCD_DATA11 | SAI3_RX_BCLK
CSI_DATA19 EIM_DATA03 GPIO3_IO16 SRC_BT_CFG11 FLEXCAN2_RX EPDC_PWRSTAT |
LCD interface signal or universal GPIO with 3.3V logic levels. |
149 | LCD | LCD-DATA5 | LCD_DATA05 | UART8_RTS_B
ENET2_1588_EVENT2_OUT SPDIF_OUT GPIO3_IO10 SRC_BT_CFG05 ECSPI1_SS1 EPDC_SDDO05 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
150 | LCD | LCD-DATA12 | LCD_DATA12 | SAI3_TX_SYNC
CSI_DATA20 EIM_DATA04 GPIO3_IO17 SRC_BT_CFG12 ECSPI1_RDY EPDC_PWRCTRL00 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
151 | LCD | LCD-DATA6 | LCD_DATA06 | UART7_CTS_B
ENET2_1588_EVENT3_IN SPDIF_LOCK GPIO3_IO11 SRC_BT_CFG06 ECSPI1_SS2 EPDC_SDDO06 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
152 | LCD | LCD-DATA10 | LCD_DATA10 | SAI3_RX_SYNC
CSI_DATA18 EIM_DATA02 GPIO3_IO15 SRC_BT_CFG10 FLEXCAN2_TX EPDC_PWRCOM |
LCD interface signal or universal GPIO with 3.3V logic levels. |
153 | LCD | LCD-DATA0 | LCD_DATA00 | PWM1_OUT
ENET1_1588_EVENT2_IN I2C3_SDA GPIO3_IO05 SRC_BT_CFG00 SAI1_MCLK EPDC_SDDO00 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
154 | LCD | LCD-DATA3 | LCD_DATA03 | PWM4_OUT
ENET1_1588_EVENT3_OUT I2C4_SCL GPIO3_IO08 SRC_BT_CFG03 SAI1_RX_DATA EPDC_SDDO03 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
155 | LCD | LCD-DATA1 | LCD_DATA01 | PWM2_OUT
ENET1_1588_EVENT2_OUT I2C3_SCL GPIO3_IO06 SRC_BT_CFG01 SAI1_TX_SYNC EPDC_SDDO01 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
156 | Power | GND | - | - | - |
157 | LCD | LCD-RESET | LCD_RESET | LCDIF_CS
CA7_MX6ULL_EVENT ISAI3_TX_DATA WDOG1_WDOG_ANY GPIO3_IO04 ECSPI2_SS3 EPDC_GDOE |
LCD interface signal or universal GPIO with 3.3V logic levels. |
158 | LCD | LCD-DATA4 | LCD_DATA04 | UART8_CTS_B
ENET2_1588_EVENT2_IN SPDIF_SR_CLK GPIO3_IO09 SRC_BT_CFG04 SAI1_TX_DATA EPDC_SDDO04 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
159 | Power | GND | - | - | - |
160 | LCD | LCD-HSYNC | LCD_HSYNC | LCDIF_RS
UART4_CTS_B SAI3_TX_BCLK WDOG3_WDOG_RST_B_DEB GPIO3_IO02 ECSPI2_SS1 EPDC_SDOE |
LCD interface signal or universal GPIO with 3.3V logic levels. |
161 | LCD | LCD-CLK | LCD_CLK | LCDIF_WR_RWN
UART4_TX SAI3_MCLK EIM_CS2_B GPIO3_IO00 WDOG1_WDOG_RST_B_DEB EPDC_SDCLK |
LCD interface signal or universal GPIO with 3.3V logic levels.
10R resistor connected in series. |
162 | LCD | LCD-VSYNC | LCD_VSYNC | LCDIF_BUSY
UART4_RTS_B SAI3_RX_DATA WDOG2_WDOG_B GPIO3_IO03 ECSPI2_SS2 EPDC_SDCE00 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
163 | LCD | LCD-ENABLE | LCD_ENABLE | LCDIF_RD_E
UART4_RX SAI3_TX_SYNC EIM_CS3_B GPIO3_IO01 ECSPI2_RDY EPDC_SDLE |
LCD interface signal or universal GPIO with 3.3V logic levels. |
164 | LCD | LCD-DATA2 | LCD_DATA02 | PWM3_OUT
ENET1_1588_EVENT3_IN I2C4_SDA GPIO3_IO07 SRC_BT_CFG02 SAI1_TX_BCLK EPDC_SDDO02 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
165 | Power | GND | - | - | - |
166 | LCD | LCD-DATA7 | LCD_DATA07 | UART7_RTS_B
ENET2_1588_EVENT3_OUT SPDIF_EXT_CLK GPIO3_IO12 SRC_BT_CFG07 ECSPI1_SS3 EPDC_SDDO07 |
LCD interface signal or universal GPIO with 3.3V logic levels. |
167 | SDIO | SDIO1-D0 | SD1_DATA0 | GPT2_COMPARE3
SAI2_TX_SYNC FLEXCAN1_TX EIM_ADDR21 GPIO2_IO18 ANATOP_OTG1_ID |
SDIO interface signal or universal GPIO with 3.3V logic levels. |
168 | Power | GND | - | - | - |
169 | SDIO | SDIO1-D3 | SD1_DATA3 | GPT2_CAPTURE2
SAI2_TX_DATA FLEXCAN2_RX EIM_ADDR24 GPIO2_IO21 CCM_CLKO2 ANATOP_OTG2_ID |
SDIO interface signal or universal GPIO with 3.3V logic levels. |
170 | Power | GND | - | - | - |
171 | SDIO | SDIO1-D1 | SD1_DATA1 | GPT2_CLK
SAI2_TX_BCLK FLEXCAN1_RX EIM_ADDR22 GPIO2_IO19 USB_OTG2_PWR |
SDIO interface signal or universal GPIO with 3.3V logic levels. |
172 | Power | GND | - | - | - |
173 | SDIO | SDIO1-CMD | SD1_CMD | GPT2_COMPARE1
SAI2_RX_SYNC SPDIF_OUT EIM_ADDR19 GPIO2_IO16 SDMA_EXT_EVENT00 USB_OTG1_PWR |
SDIO interface signal or universal GPIO with 3.3V logic levels. |
174 | Power | GND | - | - | - |
175 | SDIO | SDIO1-D2 | SD1_DATA2 | GPT2_CAPTURE1
SAI2_RX_DATA FLEXCAN2_TX EIM_ADDR23 GPIO2_IO20 CCM_CLKO1 USB_OTG2_OC |
SDIO interface signal or universal GPIO with 3.3V logic levels. |
176 | Power | GND | - | - | - |
177 | Power | GND | - | - | - |
178 | Power | GND | - | - | - |
179 | SDIO | SDIO1-CLK | SD1_CLK | GPT2_COMPARE2
SAI2_MCLK SPDIF_IN EIM_ADDR20 GPIO2_IO17 USB_OTG1_OC |
SDIO interface signal or universal GPIO with 3.3V logic levels. |
180 | Power | GND | - | - | - |
181 | Power | GND | - | - | - |
182 | Power | GND | - | - | - |
183 | CSI | CSI-PIXCLK | CSI_PIXCLK | USDHC2_WP
RAWNAND_CE3_B I2C1_SCL EIM_OE GPIO4_IO18 SNVS_HP_VIO_5 UART6_RX ESAI_TX2_RX3 |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-WAKE in SOM with WiFi/BT module |
184 | Power | GND | - | - | - |
185 | Power | GND | - | - | - |
186 | CSI | CSI-DATA6 | CSI_DATA06 | USDHC2_DATA6
ECSPI1_MOSI EIM_AD06 GPIO4_IO27 SAI1_RX_DATA USDHC1_RESET_BE SAI_TX5_RX0 |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-OUT in SOM with WiFi/BT module |
187 | CSI | CSI-MCLK | CSI_MCLK | USDHC2_CD_B
RAWNAND_CE2_B I2C1_SDA EIM_CS0_B GPIO4_IO17 SNVS_HP_VIO_5_CTL UART6_TX ESAI_TX3_RX2 |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-ENABLE in SOM with WiFi/BT module |
188 | CSI | CSI-DATA7 | CSI_DATA07 | USDHC2_DATA7
ECSPI1_MISO EIM_AD07 GPIO4_IO28 SAI1_TX_DATA USDHC1_VSELECT ESAI_TX0 |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-IN in SOM with WiFi/BT module |
189 | Power | GND | - | - | - |
190 | CSI | CSI-DATA5 | CSI_DATA05 | USDHC2_DATA5
USDHC2_DATA5 EIM_AD05 GPIO4_IO26 SAI1_TX_BCLK USDHC1_CD_BE SAI_TX_CLK |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-CLK in SOM with WiFi/BT module |
191 | CSI | CSI-DATA4 | CSI_DATA04 | USDHC2_DATA4
ECSPI1_SCLK EIM_AD04 GPIO4_IO25 SAI1_TX_SYNC USDHC1_WP ESAI_TX_FS |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-PCM-SYNC in SOM with WiFi/BT module |
192 | CSI | CSI-DATA3 | CSI_DATA03 | USDHC2_DATA3
ECSPI2_MISO EIM_AD03 GPIO4_IO24 SAI1_RX_BCLK UART5_CTS_B ESAI_RX_CLK |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-CTS in SOM with WiFi/BT module |
193 | CSI | CSI-DATA1 | CSI_DATA01 | USDHC2_DATA1
ECSPI2_SS0 EIM_AD01 GPIO4_IO22 SAI1_MCLK UART5_RX ESAI_RX_HF_CLK |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-TXD in SOM with WiFi/BT module |
194 | CSI | CSI-DATA2 | CSI_DATA02 | USDHC2_DATA2
ECSPI2_MOSI EIM_AD02 GPIO4_IO23 SAI1_RX_SYNC UART5_RTS_B ESAI_RX_FS |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-RTS in SOM with WiFi/BT module |
195 | CSI | CSI-DATA0 | CSI_DATA00 | USDHC2_DATA0
ECSPI2_SCLK EIM_AD00 GPIO4_IO21 SRC_INT_BOOT UART5_TX ESAI_TX_HF_CLK |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-RXD in SOM with WiFi/BT module |
196 | Power | CSI-VREF | - | - | Leave open if not used. |
197 | CSI | CSI-HSYNC | CSI_HSYNC | USDHC2_CMD
I2C2_SCL EIM_LBA_B GPIO4_IO20 PWM8_OUT UART6_CTS_B ESAI_TX1 |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
WLAN-HWAKE in SOM with WiFi/BT module |
198 | CSI | CSI-VSYNC | CSI_VSYNC | SDHC2_CLK
I2C2_SDA EIM_RW GPIO4_IO19 PWM7_OUT UART6_RTS_B ESAI_TX4_RX1 |
Video CMOS sensor signal or universal GPIO with 3.3V logic levels.
BT-HWAKE in SOM with WiFi/BT module |
199 | Power | GND | - | - | - |
200 | Power | GND | - | - | - |