Personal tools

SLH2-comm Datasheet and Pinout: Difference between revisions

From SomLabs Wiki

Jump to: navigation, search
← Older editNewer edit →
Line 128: Line 128:
|}
|}


== MIPI-DSI (input) Pinout ==
== SBC (StarSBC-6ULL) connectors Pinout ==
<br>
<br>
[[File:sl-mipi-lvds-hdmi-cnv-MIPI-conn.png|center]]
[[File:sl-mipi-lvds-hdmi-cnv-MIPI-conn.png|center]]

Revision as of 08:31, 14 December 2022

SLH2-comm - multiprotocol communication interface for StarSBC-6ULL equipped with RS232, RS485 and CAN physical interfaces Datasheet and Pinout

General description


SL-MIPI-LVDS-HDMI-CNV (MIPI-DSI to LVDS HDMI converter) is flexible MIPI-DSI to LVDS and/or HDMI converter. The solution we dedicate to SoMLabs carrier boards equipped with MIPI-DSI interface (with FPC30 connector). Converter is fully compliant with DSI1.02 and HDMI1.4 and converts video stream up to 1080p @60Hz/8b. SL-MIPI-LVDS-HDMI-CNV is fully compatible with SoMLabs carrier borads equipeed with MIPI-CSI FPC30 connector.

Features

  • MIPI-DSI to LVDS and/or HDMI display converter
  • Integrated D-PHY1.1 (DSI1.02)
  • From 1 up to 4 MIPI input data lanes
  • Compatible with MIPI-DSI data packets: 18bpp, RGB666 and 24bpp RGB888
  • Input bandwidth up tp 6Gb/s (4 lanes)
  • LVDS output clocking up to 154 MHz
  • Fully compatible with SoMLabs carrier board:
    • VisionCB-8M-STD (dedicated to i.MX8M mini multicore MPU)
    • VisionCB-STM32MP1-STD (dedicated to STM32MP1 multicore MPU)
  • Plug & Play solution for SoMLabs customers
  • Integrated stereo audio channel
  • Connection with carrier board using FPC30 cable A-A type

Pictures





Ordering info

SL-MIPI-LVDS-HDMI-CNV - FPC 30-pin flat cable (A-A) is included.

Operating ranges

Parameter Value Unit Comment
Power Supply
3.3 & 5.0
V
 Powered from carrier board
Current
0.1
A
 Maximum peak value
Environment temperature
-40…+85
 oC -

Electrical parameters

Signal name Parameter Value Units
Min. Typ. Max.
+5V Supply Voltage 4.75 5.0 5.25 V
+3.3V Supply Voltage 3.2 3.3 3.35 V
I5V Supply Current (5V) 40 80 100 mA
I3.3V Supply Current (3.3V) 1 2.2 8 mA
VIOI2C I2C Input Voltage 0 3.3 3.6 V
VIORES/SPDIF RES/SPDIF Input Voltage 0 3.3 3.6 V
fI2C I2C Controller Speed - - 400 kHz
RINT Interrupt Output Pull-up Resistance - 4.7 - kΩ
RI2C I2C IOs Pull-up Resistance - 4.7 - kΩ

SBC (StarSBC-6ULL) connectors Pinout




Connector pin number Default function MPU GPIO MPU ball numer BGA289 Notes
J1
1 +3,3VO +3,3V power supply delivered from StarSBC-6ULL, paralelly connected to pin 1 of J1
2 +5V 5V power supply delivered from StarSBC-6ULL, paralelly connected to pin 2 of J1
3 UART8-RXD ENET2_TX_EN B15 RXD line of UART8 with RS485 level converter (J200), half-duplex, direction line GPIO3.26
4 GND
5 UART8-TXD ENET2_TX_DATA1 A16 TXD line of UART8 with RS485 level converter (J200), half-duplex, direction line GPIO3.26
6 UART3-TXD UART3_TX_DATA H17 TXD line of UART3 with RS232 level converter (J300)
7 - - -
8 UART3-RXD UART3_RX_DATA H16 RXD line of UART3 with RS232 level converter (J300)
9 GND
10 UART3-CTS UART3_CTS H15 CTS line of UART3 with RS232 level converter (J300)
11 UART4-RXD LCD_ENABLE B8 RXD line of UART4 with RS485 level converter (J200), half-duplex, direction line GPIO3.25
12 UART3-RTS UART3_RTS G14 RTS line of UART3 with RS232 level converter (J300)
13 UART4-TXD LCD_CLK A8 TXD line of UART4 with RS485 level converter (J200), half-duplex, direction line GPIO3.25
14 GND
15 - - -
16 - - -
17 - - -
18 - - -
19 - - -
20 UART7-RXD LCD_DATA16 C13 RXD line of UART3 with RS232 level converter (J301)
21 - - -
22 UART7-TXD LCD_DATA17 B13 TXD line of UART3 with RS232 level converter (J301)
23 - - -
24 UART7-CTS LCD_DATA07 D11 CTS line of UART3 with RS232 level converter (J301)
25 - - -
26 UART7-RTS LCD_DATA06 A10 CTS line of UART3 with RS232 level converter (J301)
J2
1 +3,3VO +3,3V power supply delivered from StarSBC-6ULL, paralelly connected to pin 1 of J1
2 +5V 5V power supply delivered from StarSBC-6ULL, paralelly connected to pin 2 of J1
3 - - -
4 GND
5 - - -
6 - - -
7 GPIO3.17 LCD_DATA12 C12 Pul-down 10k resistor optionally used for module ("hat") identification
8 - - -
9 GND
10 - - -
11 CAN1-TX LCD_DATA08 B11 TX line of CAN1 with CAN-FD level converter (J100 and J101)
12 - - -
13 CAN1-RX LCD_DATA09 A11 RX line of CAN1 with CAN-FD level converter (J100 and J101)
14 GND
15 CAN2-TX LCD_DATA10 E12 TX line of CAN2 with CAN-FD level converter (J100 and J101)
16 - - -
17 CAN2-RX LCD_DATA11 D12 RX line of CAN2 with CAN-FD level converter (J100 and J101)
18 - - -
19 MQS-R LCD_DATA22 A14 Not used by default
20 - - -
21 MQS-L LCD_DATA23 B16 Not used by default
22 - - -
23 GPIO3.25 LCD_DATA20 C14 RS485 semiduplex direction line (UART4)
24 - - -
25 GPIO3.26 LCD_DATA21 B14 RS485 semiduplex direction line (UART8)
26 - - -

LVDS (output) Pinout




LVDS connector pin Function name Description
1 +5V Power supply for external devices (max. 20 mA)
Internally connected with pin 2
2 +5V Power supply for external devices (max. 20 mA)
Internally connected with pin 1
3 - -
4 GND -
5 GND -
6 GND -
7 D0n LVDS D0n data line
8 D0p LVDS D0p data line
9 D1n LVDS D1n data line
10 D1p LVDS D1p data line
11 D2n LVDS D2n data line
12 D2p LVDS D2p data line
13 GND -
14 GND -
15 CLKn LVDS CLKn clock line
16 CLKp LVDS CLKp clock line
17 D3n LVDS D3n data line
18 D3p LVDS D3p data line

HDMI (output) Pinout



HDMI connector built-in SL-MIPI-LVDS-HDMI-CNV converter has standard HDMI pinout.

Dimensions


Retrieved from "https://wiki.somlabs.com/index.php?title=SLH2-comm_Datasheet_and_Pinout&oldid=3035"