Personal tools

VisionCB-x2L-STD Datasheet and Pinout: Difference between revisions

From SomLabs Wiki

Jump to: navigation, search
← Older editNewer edit →
Line 951: Line 951:
|}
|}


== Dimensions ==
== RECOVERY jumper ==
[[File:VisionCB-x2L-STD-dimensions.png|800px|center]]
[[File:VisionCB-x2L-STD-recovery.png|800px|center]]

Revision as of 10:06, 4 January 2024

VisionCB-x2L-STD v.1.2 Datasheet and Pinout

General description

The VisionCB-x2L-STD (with SOM equipped with Renesas RZ/V2L and RZ/G2L MPUs compatible) is a carrier board for the VisionSOM-V2L and VisionSOM-G2L family of computer-on-modules which are powered by dual-core Renesas MPUs (2 x ARM Cortex-A55 + Cortex-M33). The carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as USB, Ethernet, CAN, RS485, audio codec, etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product. The VisionCB-x2L-STD is equipped with a simple user interface consisting of 4 buttons and 4 LEDs. VisionCB-x2L-STD carrier board is also equipped with a large number of popular peripherals, including: RS485, CAN, 10/100/1G Ethernet, MIPI display and camera connectors, serial console port on USB vCOM.

Applications

  • Multimedia
  • Video streaming
  • Image inspection
  • VisionAI gateway
  • Doorbell systems
  • EV chargers
  • Smart agriculture gateways
  • Industrial embedded Linux computer
  • Home Appliances
  • Home Automation – Smart Home
  • Human-machine Interfaces (HMI)
  • Point-of-sales (POS) terminals
  • IoT gateways
  • Machine vision equipment
  • Robotics
  • Fitness/outdoor equipment

Features

  • Carrier Board compatible with the VisionSOM-G2L and VisionSOM-V2L families of modules based on dual core, heterogenous Renesas RZ/V2L and RZ/G2L application processors
  • SoM Connector: SODIMM200
  • Expansion Connectors:
    • ADC+GPIO connector 2x9 Pin Header (Male)
    • Raspberry Pi Compatible Connectors 2x20 Pin Header (Male)
    • Ethernet #1 (GMII) Connector Pin Header (Male)
  • Communication Connectors:
    • 1x Ethernet 10/100/1000Mbit/s (RJ45)
    • 1x CAN (1x3 Pin Header, Male)
    • 1x RS-485 (1x3 Pin Header, Male)
    • 1x USB Host Type A connectors
    • 1x USB OTG Micro AB connector
    • 1x Console MicroUSB B connector
  • Audio Interface:
    • Mini-jack 3.5mm (headphones + microphone)
  • Display Interface:
    • 30-pin FFC/FPC MIPI-DSI (up to 4 lanes)
  • Camera Interface:
    • 30-pin FFC/FPC MIPI-CSI2 (up to 4 lanes)
  • User Interface:
    • 4+1 Pushbuttons
    • 4+2 LEDs
  • External Power Supply 9-12V DC
  • Temperature Range: 0 to +70°C
  • Board Size: 160mm x 100mm x 21mm

Pictures of VisionCB-x2L-STD v1.2 board

Version Photo
VisionCB-x2L-STD v1.2 board only
VisionCB-x2L-STD v1.2 with VisionSOM-x2L

Ordering info

VisionCB-x2L-STD v1.2

Block Diagram

Electrical parameters

Parameter Value Units Comment
Min. Typ. Max.
Power Supply 9.0 12.0 15.0 V Positive pole on central connector of J200
Supply current - - 0.13 A Excluding LCD, USB and antoher external loads
LCD/Camera Power Supply
(logic) 		3.25 3.3 3.35 V -
LCD/Camera Power Supply
(backlight and aux) 		4.75 4.87 4.95 V -
Arduino GPIO voltage 3.3 V -

Power supply connector

The VisionCB-x2L-STD is equipped with external power source connector with pin diameter 2.5mm and hole diameter 6mm. The voltage of the external power source should be within the range 9-12 VDC.

Camera MIPI-CSI interface (FPC/FFC30, 0.5mm)

Pin Signal GPIO Description
1 GND - -
2 CSI-CLK-P - -
3 CSI-CLK-P - -
4 GND - -
5 CSI-DATA0-P - -
6 CSI-DATA0-N - -
7 GND - -
8 CSI-DATA1-P - -
9 CSI-DATA1-N - -
10 GND - -
11 CSI-DATA2-P - -
12 CSI-DATA2-N - -
13 GND - -
14 CSI-DATA3-P - -
15 CSI-DATA3-N - -
16 GND - -
17 I2C1-SCL RIIC1_SCL Camera confguration I2C interface (3.3V), pull-uped with 2.2k
18 I2C1-SDA RIIC1_SDA Camera confguration I2C interface (3.3V), pull-uped with 2.2k
19 GND - -
20 CSI-GPIO0 P17-0 Auxiliary GPIO
21 CSI-GPIO1 P17-1 Auxiliary GPIO
22 - - -
23 GND - -
24 +3.3V - Power supply for external devices
25 +3.3V - Power supply for external devices
26 +5V - Power supply for external devices
27 +5V - Power supply for external devices
28 - - -
29 - - -
30 GND - -

Note:
1. The first pin of the MIPI-CSI connector is located in its upper part.

Display MIPI-DSI interface (FPC/FFC30, 0.5mm)

Pin Signal GPIO Description
1 GND -
2 DSI-CLK-P - -
3 DSI-CLK-P - -
4 GND - -
5 DSI-DATA0-P - -
6 DSI-DATA0-N - -
7 GND - -
8 DSI-DATA1-P - -
9 DSI-DATA1-N - -
10 GND - -
11 DSI-DATA2-P - -
12 DSI-DATA2-N - -
13 GND - -
14 DSI-DATA3-P - -
15 DSI-DATA3-N - -
16 GND - -
17 I2C1-SCL RIIC1_SCL Display confguration I2C interface (3.3V), pull-uped with 2.2k
18 I2C1-SDA RIIC1_SDA Display confguration I2C interface (3.3V), pull-uped with 2.2k
19 GND - -
20 DISP-RST P13-2 Optional display reset signal
21 TP-INT P17-1 Optional touch-panel interrupt signal
22 TP-RST P17-2 Optional touch-panel reset signal
23 GND - -
24 +3.3V - Power supply for external devices
25 +3.3V - Power supply for external devices
26 +5V - Power supply for external devices
27 +5V - Power supply for external devices
28 DSI-BL-PWM P16-0 Optional PWM backlight signal
29 DSI-BL-EN P16-1 Optional ENABLE backlight signal
30 GND - -

Note:
1. The first pin of the MIPI-DSI connector is located in its upper part.

USB Console Port

Console line MPU signal GPIO Description
CONSOLE-TXD UART0-RXD P38-1 GPIO 3.3V voltage levels
CONSOLE-RXD UART0-TXD P38-0 GPIO 3.3V voltage levels

ADC + GPIO connector


Pin Signal GPIO Description
1 GND - -
2 3.3V - -
3 ADC-CH0 ADC-CH0 Dedicated analog input, 12-bit ADC, max. 1.8V on input
4 ADC-CH1 ADC-CH1 Dedicated analog input, 12-bit ADC, max. 1.8V on input
5 ADC-CH2 ADC-CH2 Dedicated analog input, 12-bit ADC, max. 1.8V on input
6 ADC-CH3 ADC-CH3 Dedicated analog input, 12-bit ADC, max. 1.8V on input
7 ADC-CH4 ADC-CH4 Dedicated analog input, 12-bit ADC, max. 1.8V on input
8 ADC-CH5 ADC-CH5 Dedicated analog input, 12-bit ADC, max. 1.8V on input
9 ADC-CH6 ADC-CH6 Dedicated analog input, 12-bit ADC, max. 1.8V on input
10 ADC-CH7 ADC-CH7 Dedicated analog input, 12-bit ADC, max. 1.8V on input
11 P12-0 P12-0 GPIO 3.3V voltage levels
12 P13-1 P13-1 GPIO 3.3V voltage levels
13 P7-2 P7-2 GPIO 3.3V voltage levels
14 P11-0 P11-0 GPIO 3.3V voltage levels
15 P48-2 P48-2 GPIO 3.3V voltage levels
16 P4-1 P4-1 GPIO 3.3V voltage levels
17 CAN1-RX P13-0 GPIO 3.3V voltage levels
18 CAN1-TX P12-1 GPIO 3.3V voltage levels

Raspberry Pi compatible I/O header

Pin Signal MPU signal Description
1 3.3V - -
2 5.0V - -
3 I2C0-SDA RIIC0_SDA Dedicated I2C MPU line
4 5.0V - -
5 I2C0-SCL RIIC0_SCL Dedicated I2C MPU line
6 GND - -
7 P45-0 P45-0 GPIO 3.3V voltage levels
8 UART4-TXD P2-0 GPIO 3.3V voltage levels
9 GND - -
10 UART4-RXD P2-1 GPIO 3.3V voltage levels
11 P8-2 P8-2 GPIO 3.3V voltage levels
12 P15-0 P15-0 GPIO 3.3V voltage levels
13 P14-1 P14-1 GPIO 3.3V voltage levels
14 GND - -
15 P14-0 P14-0 GPIO 3.3V voltage levels
16 UART1-RXD P40-0 GPIO 3.3V voltage levels
17 P11-1 P11-1 GPIO 3.3V voltage levels
18 UART1-TXD P40-1 GPIO 3.3V voltage levels
19 SPI0-MOSI P43-1 GPIO 3.3V voltage levels
20 GND - -
21 SPI0-MISO P43-2 GPIO 3.3V voltage levels
22 P9-1 P9-1 GPIO 3.3V voltage levels
23 SPI0-CLK P43-0 GPIO 3.3V voltage levels
24 SPI0-SSL P43-3 GPIO 3.3V voltage levels
25 GND - -
26 P9-0 P9-0 GPIO 3.3V voltage levels
27 I2C3-SDA P46-2 I2C interface used by MPU for SOM PMIC configuration
28 I2C3-SCL P46-3 I2C interface used by MPU for SOM PMIC configuration
29 UART1-CTS P41-0 GPIO 3.3V voltage levels
30 GND - -
31 UART1-RTS P41-1 GPIO 3.3V voltage levels
32 P1-1 P1-1 GPIO 3.3V voltage levels
33 P10-1 P10-1 GPIO 3.3V voltage levels
34 GND - -
35 SPI1-MISO P44-2 GPIO 3.3V voltage levels
36 SPI1-SSL P44-3 GPIO 3.3V voltage levels
37 P10-0 P10-0 GPIO 3.3V voltage levels
38 SPI1-MOSI P44-1 GPIO 3.3V voltage levels
39 GND - -
40 SPI1-CLK P44-0 GPIO 3.3V voltage levels

GMII of ETH0 connection

Signal MPU signal Description
ET0-TXD0 ET0-TXD0 1.8V Power Domain, GPIO mode not allowed
ET0-TXD1 ET0-TXD1 1.8V Power Domain, GPIO mode not allowed
ET0-TXD2 ET0-TXD2 1.8V Power Domain, GPIO mode not allowed
ET0-TXD3 ET0-TXD3 1.8V Power Domain, GPIO mode not allowed
ET0-TXC ET0-TXC 1.8V Power Domain, GPIO mode not allowed
ET0-TX-CTL ET0-TX-CTL 1.8V Power Domain, GPIO mode not allowed
ET0-RXD0 ET0-RXD0 1.8V Power Domain, GPIO mode not allowed
ET0-RXD1 ET0-RXD1 1.8V Power Domain, GPIO mode not allowed
ET0-RXD2 ET0-RXD2 1.8V Power Domain, GPIO mode not allowed
ET0-RXD3 ET0-RXD3 1.8V Power Domain, GPIO mode not allowed
ET0-RXC ET0-RXC 1.8V Power Domain, GPIO mode not allowed
ET0-RX-CTL ET0-RX-CTL 1.8V Power Domain, GPIO mode not allowed
ET0-MDC ET0-MDC 1.8V Power Domain, GPIO mode not allowed
ET0-MDIO ET0-MDIO 1.8V Power Domain, GPIO mode not allowed
ET0-INT P47-0 GPIO 3.3V voltage levels
ET0-PHY-RST P47-1 GPIO 3.3V voltage levels

GMII of ETH1 connector

Pin Signal MPU signal Description
1 3.3V - -
2 ET1-TXD0 P30-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
3 ET1-TXD1 P30-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
4 ET1-TXD2 P31-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
5 ET1-TXD3 P31-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
6 ET1-TXC P29-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
7 ET1-TX-CTL P29-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
8 ET1-RXD3 P36-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
9 ET1-RXD2 P35-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
10 ET1-RXD1 P35-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
11 ET1-RXD0 P34-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
12 ET1-RX-CTL P34-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
13 ET1-RXC P33-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
14 ET1-MDC P37-0 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
15 ET1-MDIO P37-1 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
16 ET1-INT P47-2 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
17 ET1-PHY-RST P47-3 1.8V or 3.3V Power Domain selected by ET1-VDD-SEL, GPIO allowed only for 3.3V.
18 ET1-VDD-SEL - Ethernet 1 (ET1) interface voltage selection:
ET1-VDD-SEL='0' -> V=1.8V;
ET1-VDD-SEL='1' or left open -> V=3.3V
The line has internal pull-up.
19 GND - -
20 GND - -

USB interfaces

Signal MPU signal Description
USB0-ID P5-1 GPIO 3.3V voltage levels
USB0-EN P4-0 GPIO 3.3V voltage levels
USB0-OC P5-0 GPIO 3.3V voltage levels
USB1-EN P8-0 GPIO 3.3V voltage levels
USB1-OC P8-1 GPIO 3.3V voltage levels

Note:
1. USB0 is configured as host, USB1 channel is configured as USB-OTG.

Audio codec

Signal MPU signal Description
SSI-MCLK AUDIO_CLK1 GPIO 3.3V voltage levels
SSI0-BCK P6-0 GPIO 3.3V voltage levels
SSI0-RCK P6-1 GPIO 3.3V voltage levels
SSI0-TXD P7-0 GPIO 3.3V voltage levels
SSI0-RXD P7-1 GPIO 3.3V voltage levels

Note:
1. Audio codec is configured via I2C2 MPU interface.

CAN interface

Signal MPU signal Description
CAN0-RX P42-2 GPIO 3.3V voltage levels
CAN0-TX P42-1 GPIO 3.3V voltage levels
CAN0-STB P18-1 GPIO 3.3V voltage levels (STB line of MCP2542FD)

RS-485 interface

Signal MPU signal Description
UART3-RXD P0-1 GPIO 3.3V voltage levels
UART3-TXD P0-0 GPIO 3.3V voltage levels
RS485-RE P18-0 GPIO 3.3V voltage levels
In default configuration RS485-RE is connected to nRE and DE inputs of MAX3485
RS485-DE P19-0 GPIO 3.3V voltage levels
In default configuration this line is not used

User Interface (switches and LEDs)

Signal MPU signal Description
User LEDs
P45-2 P45-2 Inverted logic level
P45-3 P45-3 Inverted logic level
P46-0 P46-0 Inverted logic level
P46-1 P46-1 Inverted logic level
SYS-LED P42-0 Inverted logic level
User switch
P1-0 P1-0 Pushbutton, line pull-uped
P3-0 P3-0 Pushbutton, line pull-uped
P3-1 P3-1 Pushbutton, line pull-uped
P45-1 P45-1 Pushbutton, line pull-uped

RECOVERY jumper

Retrieved from "https://wiki.somlabs.com/index.php?title=VisionCB-x2L-STD_Datasheet_and_Pinout&oldid=3781"