VisionCB-RT1176-STD v.1.2 Datasheet and Pinout

VisionCB-RT1176-STD v.1.2 Datasheet and Pinout

---

General description

VisionCB-RT1176-STD is a carrier board for the VisionSOM-RT1170 family of computer-on-modules, which are powered by NXP i.MX RT117x application processors. The carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as audio codec, USB, Ethernet, UART, RS485, CAN etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product.

The carrier board connects with the SoM via a standard SODIMM connector.

Applications

• Digital cluster
• Home Control Panel
• Home Automation – Smart Home
• Human-machine Interfaces (HMI)
• Point-of-sales (POS) terminals
• Motor Drives
• 2D barcode scanners and printers
• Smart grid infrastructure
• IoT gateways
• Transport ticketing
• PV Energy Generation
• Robotic appliance
• Fitness/outdoor equipment

Features

• Carrier Board (Base Board) compatible with the VisionSOM family of modules based on NXP i.MX RT117x application processors
• SoM connector: SODIMM200
• Expansion Connectors:
  • GPIO-SNVS, GPIO-COMM1, GPIO-COMM2 2x16 Pin Headers (Male)
  • MicroSD socket
• Audio:
  • 24-bit codec audio with headphones and microphone Jack connector
• Communication Connectors:
  • 1x JTAG connector
  • RS485 half-duplex
  • CAN single channel
  • 1x Ethernet 10/100/1000 Mbit/s, RJ45
  • 1x USB Host Type A connectors
  • 1x USB-OTG Micro AB connector
  • 1x Console MicroUSB B connector (Mbed SWDAP debug probe based on LPC11U35FHI33/501)
• Display Interface: 30-pin FFC/FPC MIPI-DSI
• Camera Interface: 30-pin FFC/FPC MIPI-CSI
• User Interface:
  • 5 Pushbuttons
  • 5 LEDs
• Recovery jumper
• Power Supply
  • DC connector: Input Voltage 9-12V DC (5.5x2.1 connector)
  • CR2032 battery socket for RTC
• Temperature Range: 0 to +70°C
• Board Size: 145mm x 90mm x 22mm

Pictures of VisionCB-RT1176-STD v1.2 board

Version	Photo
VisionCB-RT1176-STD v1.2 board with attached SOM

Ordering info

VisionCB-RT1176-STD v1.2

Block Diagram

Electrical parameters

Parameter	Value			Units	Comment
	Min.	Typ.	Max.
Power Supply (J100 input)	9.0	12.0	15.0	V	Positive pole on central connector of J100
Supply current	-	-	0.15	A	Excluding LCD, USB and antoher external loads
Output voltage (VCC-3V3)	-	3.3	-	V	Generated by internal LDO
Output VCC-3V3 current	-	-	500	mA	Generated by internal LDO
USB power supply	4.75	4.9	5.5	V	On J201 (Linux USB console connector)
Input GPIO voltage (J405)	0	-	3.3	V	LCD-RGB connector
Input GPIO voltage (J504)	0	-	3.3	V	Raspberry Pi compatible
Input GPIO voltage (J502, J503)	0	-	3.3/5 (1)	V	Arduino compatible connector (digital I/O)
Input GPIO voltage (J501)	0	-	3.3	V	Arduino compatible connector (analog inputs)

Note:
1. Depends on JP3 selector.

Recovery Jumper/MCU Boot Configuration

RECOVERY is the boot mode selector. If:

• RECOVERY = 0 (jupmer installed) then BOOT-MODE0 = 1, as a result serial loader starts
  
• RECOVERY = 1 (jumper is not installed) or open then BOOT-MODE0 = 0, as a result MCU boots from fuses
  

External JTAG Connector

JTAG Connector	Default function name	MCU pin name
1	+3V3	-
2	TMS	GPIO_LPSR_15
3	GND	NA
4	TCK	GPIO_LPSR_14
5	GND	NA
6	TDO	GPIO_LPSR_11
7	-	-
8	TDI	GPIO_LPSR_12
9	GND	GPIO_AD_B0_07
10	nRES/TRST	GPIO_LPSR_10

DAP Debug Interface

The DAP debug interface is based on LPC11U35FHI33/501 and converts USB into two-lines SWD debug interface.
The DAP debug interface also serves as an vCOM (on USB) interface for optional UART console port.

SWDIO DAP Connector

DAP Connector	Function name	Source: DAP/SoM
1	nRES	DAP
2	nRESET	DAP
3	SWCLK	DAP
4	TCK	SoM
5	SWDIO	DAP
6	TMS	SoM

Note:
1. During normal use, it is recommended to connect pin pairs: 1-2, 3-4, 5-6.

Console DAP Connector

DAP Connector	Function name	Signal Source
1	RxD	DAP
2	UART2.RxD	SoM
3	TxD	DAP
4	UART2.TxD	SoM

Note:
1. During normal use, it is recommended to connect pin pairs: 1-2, 3-4.

GPIO COMM1 I/O header (J802)

J802 Pin	Default function name	MCU pin name	Description
1	SPI4.SCK	GPIO_DISP_B2_12	3.3V logic levels
2	SPI4.OUT	GPIO_DISP_B2_14	3.3V logic levels
3	SPI4.IN	GPIO_DISP_B2_13	3.3V logic levels
4	SPI4.CS0	GPIO_DISP_B2_15	3.3V logic levels
5	I2C1.SDA	GPIO_AD_33	External 4,7k pull-up resistor
6	I2C1.SCL	GPIO_AD_32	External 4,7k pull-up resistor
7	I2C2.SDA	GPIO_AD_19	External 4,7k pull-up resistor
8	I2C2.SCL	GPIO_AD_18	External 4,7k pull-up resistor
9	CAN2.TX	GPIO_AD_00	3.3V logic levels
10	CAN2.RX	GPIO_AD_01	3.3V logic levels
11	UART1.RXD	GPIO_AD_25	Available to the user as GPIO only in SoM without 1DX radio modules.
12	UART1.TXD	GPIO_AD_24	Available to the user as GPIO only in SoM without 1DX radio modules.
13	UART1.CTS	GPIO_AD_26	Available to the user as GPIO only in SoM without 1DX radio modules.
14	UART1.RTS	GPIO_AD_27	Available to the user as GPIO only in SoM without 1DX radio modules.
15	+3V3	NA	-
16	GND	NA	-

Notes:
1. NA - not available.

GPIO COMM2 I/O header (J801)

J801 Pin	Default function name	MCU pin name	Description
1	UART5.TXD	GPIO_AD_28	3.3V logic levels
2	UART3.TXD	GPIO_AD_30	3.3V logic levels
3	UART5.RXD	GPIO_AD_29	3.3V logic levels
4	UART3.RXD	GPIO_AD_31	3.3V logic levels
5	UART10.TXD	GPIO_AD_15	Pushbutton S804 is connected to this line.
6	UART12.TXD	GPIO_LPSR_00	GPIO_LPSR00 LED is connected to this line (through logic inverter).
7	UART10.RXD	GPIO_AD_16	Pushbutton S803 is connected to this line.
8	UART12.RXD	GPIO_LPSR_01	GPIO_LPSR01 LED is connected to this line (through logic inverter).
9	UART10.RTS	GPIO_AD_35	Pushbutton S802 is connected to this line.
10	UART12.RTS	GPIO_LPSR_04	GPIO_LPSR04 LED is connected to this line (through logic inverter).
11	UART10.CTS	GPIO_AD_34	Pushbutton S801 is connected to this line.
12	UART12.CTS	GPIO_LPSR_05	GPIO_LPSR05 LED is connected to this line (through logic inverter).
13	NC	-	-
14	DAC-OUT	DAC-OUT	12-bit DAC voltage output (range 0-1.8V).
15	+3V3	NA	-
16	GND	NA	-

Notes:
1. NA - not available.
2. NC - not connected.

GPIO SNVS I/O header (J800)

J800 Pin	Default function name	MCU pin name	Description
1	GPIO-SVNS.9	GPIO_SNVS_09	1.75V VDD_SNVS_ANA power domain
2	GPIO-SVNS.8	GPIO_SNVS_08	1.75V VDD_SNVS_ANA power domain
3	GPIO-SVNS.7	GPIO_SNVS_07	1.75V VDD_SNVS_ANA power domain
4	GPIO-SVNS.6	GPIO_SNVS_06	1.75V VDD_SNVS_ANA power domain
5	GPIO-SVNS.5	GPIO_SNVS_05	1.75V VDD_SNVS_ANA power domain
6	GPIO-SVNS.4	GPIO_SNVS_04	1.75V VDD_SNVS_ANA power domain
7	GPIO-SVNS.3	GPIO_SNVS_03	1.75V VDD_SNVS_ANA power domain
8	GPIO-SVNS.2	GPIO_SNVS_02	1.75V VDD_SNVS_ANA power domain
9	GPIO-SVNS.1	GPIO_SNVS_01	1.75V VDD_SNVS_ANA power domain
10	GPIO-SVNS.0	GPIO_SNVS_00	1.75V VDD_SNVS_ANA power domain
11	PMIC-STBY-REQ	PMIC-STBY-REQ	1.75V VDD_SNVS_ANA power domain.
12	RESET	RESET	POR-B of MCU line (resets all of the chip except the Secure Non-Volatile Storage (SNVS) block), active low. 1.75V VDD_SNVS_ANA power domain.
13	WAKEUP	-	A GPIO powered by SNVS domain power supply which can be configured as wakeup source in SNVS mode. 1.75V VDD_SNVS_ANA power domain.
14	ON-OFF	ON-OFF	A brief connection to GND in the OFF mode causes the internal power management state machine to change the state to ON. In the ON mode, a brief connection to GND generates an interrupt intended to be a software-controllable power-down). Approximately five seconds (or more) to GND causes a forced OFF. Both boot mode inputs can be disconnected. 1.75V VDD_SNVS_ANA power domain.
15	+1V8	NA	Reference voltage for 1V8 peripherals.
16	GND	NA	-

Notes:
1. NA - not available.

User LEDs connections

LED	PCB designation	MCU pin name	Description
D400/blue	GPIO10	GPIO_AD_B0_08	Default: JTAG MOD input or universal GPIO with 3.3V logic levels.
D401/green	GPIO11	GPIO_AD_B0_06	Default: JTAG TMS input or universal GPIO with 3.3V logic levels.
D403/yellow	GPIO12	GPIO_AD_B0_10	Default: JTAG TDO input or universal GPIO with 3.3V logic levels.
D402/red	GPIO13	GPIO_AD_B0_09	Default: JTAG TDI input or universal GPIO with 3.3V logic levels.

Notes:
1. LEDs are switched on by logic „1” set at the GPIO outputs.
2. LEDs are controlled by current drivers and do not load the GPIOs.

User switches connections

Switch	PCB designation	MCU pin name	Description
S804	UART10.TXD	GPIO_AD_B0_03	Connected to .
S803	UART10.RXD	GPIO_AD_B0_04/BOOT0	Universal GPIO with 3.3V logic levels.
S802	UART10.RTS	GPIO_AD_B1_09	Universal GPIO with 3.3V logic levels.
S801	UART10.CTS	GPIO_B1_14	Universal GPIO with 3.3V logic levels.

Notes:
1. After button pressing on GPIO lines are set to „0”.
2. GPIO lines connected to switches are separated from board’s environment by 1k resistors.

TFT LCD connector (RGB 24b, J405)

J405 pin	Default function name	MCU pin name	LCD interface name
1	LCD-DATA0	Internally connected to GND	LCD-B0
2	LCD-DATA1	Internally connected to GND	LCD-B1
3	LCD-DATA2	Internally connected to GND	LCD-B2
4	LCD-DATA3	GPIO_B0_04	LCD-B3
5	LCD-DATA4	GPIO_B0_05	LCD-B4
6	LCD-DATA5	GPIO_B0_06	LCD-B5
7	LCD-DATA6	GPIO_B0_07	LCD-B6
8	LCD-DATA7	GPIO_B0_08	LCD-B7
9	GND	-	GND
10	LCD-DATA8	Internally connected to GND	LCD-G0
11	LCD-DATA9	Internally connected to GND	LCD-G1
12	LCD-DATA10	GPIO_B0_09	LCD-G2
13	LCD-DATA11	GPIO_B0_10	LCD-G3
14	LCD-DATA12	GPIO_B0_11	LCD-G4
15	LCD-DATA13	GPIO_B0_12	LCD-G5
16	LCD-DATA14	GPIO_B0_13	LCD-G6
17	LCD-DATA15	GPIO_B0_14	LCD-G7
18	GND	-	GND
19	LCD-DATA16	Internally connected to GND	LCD-R0
20	LCD-DATA17	Internally connected to GND	LCD-R1
21	LCD-DATA18	Internally connected to GND	LCD-R2
22	LCD-DATA19	GPIO_B0_15	LCD-R3
23	LCD-DATA20	GPIO_B1_00	LCD-R4
24	LCD-DATA21	GPIO_B1_01	LCD-R5
25	LCD-DATA22	GPIO_B1_02	LCD-R6
26	LCD-DATA23	GPIO_B1_03	LCD-R7
27	GND	-	GND
28	LCD-DE	GPIO_B0_01	DE
29	LCD-HSYNC	GPIO_B0_02	HSYNC
30	LCD-VSYNC	GPIO_B0_03	VSYNC
31	GND	-	GND
32	LCD-PCLK	GPIO_B0_00	DCLK
33	GND	-	GND
34	GPIO4	GPIO_AD_B0_04	TS-YPUL
35	GPIO3	GPIO_AD_B0_03	TS-YNUR
36	GPIO2	GPIO_AD_B0_02	TS-YPLL
37	GPIO1	GPIO_AD_B0_00	TS-YNLR
38	-	-	-
39	-	-	-
40	-	-	-
41	-	-	-
42	UART5-TXD	GPIO_B1_12	I2C-SCL
43	UART5-RXD	GPIO_B1_13	I2C-SDA
44	GND	-	GND
45	VCC-LCD	-	+3.3V (controlled by GPIO_AD_B0_11/JTAG-TRSTB)
46	VCC-LCD	-	+3.3V (controlled by GPIO_AD_B0_11/JTAG-TRSTB)
47	VCC-5V0	-	+5.0V
48	VCC-5V0	-	+5.0V
49	LCD-RESET	GPIO_AD_B1_08	RESET
50	JTAG-nTRST	GPIO_AD_B0_11	PWREN

Note:
1. When GPIO_AD_B0_11/JTAG-TRSTB:
= '1' LCD module power supply is OFF.
= '0' LCD module power supply is ON.

Dimensions