SLH2-comm Datasheet and Pinout
From SomLabs Wiki
SLH2-comm - multiprotocol communication interface for StarSBC-6ULL equipped with RS232, RS485 and CAN physical interfaces Datasheet and Pinout
General description
SL-MIPI-LVDS-HDMI-CNV (MIPI-DSI to LVDS HDMI converter) is flexible MIPI-DSI to LVDS and/or HDMI converter. The solution we dedicate to SoMLabs carrier boards equipped with MIPI-DSI interface (with FPC30 connector). Converter is fully compliant with DSI1.02 and HDMI1.4 and converts video stream up to 1080p @60Hz/8b.
SL-MIPI-LVDS-HDMI-CNV is fully compatible with SoMLabs carrier borads equipeed with MIPI-CSI FPC30 connector.
Features
- MIPI-DSI to LVDS and/or HDMI display converter
- Integrated D-PHY1.1 (DSI1.02)
- From 1 up to 4 MIPI input data lanes
- Compatible with MIPI-DSI data packets: 18bpp, RGB666 and 24bpp RGB888
- Input bandwidth up tp 6Gb/s (4 lanes)
- LVDS output clocking up to 154 MHz
- Fully compatible with SoMLabs carrier board:
- VisionCB-8M-STD (dedicated to i.MX8M mini multicore MPU)
- VisionCB-STM32MP1-STD (dedicated to STM32MP1 multicore MPU)
- Plug & Play solution for SoMLabs customers
- Integrated stereo audio channel
- Connection with carrier board using FPC30 cable A-A type
Pictures
Ordering info
SL-MIPI-LVDS-HDMI-CNV - FPC 30-pin flat cable (A-A) is included.
Operating ranges
| Parameter | Value | Unit | Comment |
|---|---|---|---|
| Power Supply | Powered from carrier board | ||
| Current | Maximum peak value | ||
| Environment temperature | oC | - |
Electrical parameters
| Signal name | Parameter | Value | Units | ||
|---|---|---|---|---|---|
| Min. | Typ. | Max. | |||
| +5V | Supply Voltage | 4.75 | 5.0 | 5.25 | V |
| +3.3V | Supply Voltage | 3.2 | 3.3 | 3.35 | V |
| I5V | Supply Current (5V) | 40 | 80 | 100 | mA |
| I3.3V | Supply Current (3.3V) | 1 | 2.2 | 8 | mA |
| VIOI2C | I2C Input Voltage | 0 | 3.3 | 3.6 | V |
| VIORES/SPDIF | RES/SPDIF Input Voltage | 0 | 3.3 | 3.6 | V |
| fI2C | I2C Controller Speed | - | - | 400 | kHz |
| RINT | Interrupt Output Pull-up Resistance | - | 4.7 | - | kΩ |
| RI2C | I2C IOs Pull-up Resistance | - | 4.7 | - | kΩ |
MIPI-DSI (input) Pinout
| Connector pin number | Default function | MPU GPIO | MPU ball numer BGA289 | Notes |
|---|---|---|---|---|
| J1 | ||||
| 1 | +3,3VO | +3,3V power supply delivered from StarSBC-6ULL, paralelly connected to pin 1 of J1 | ||
| 2 | +5V | 5V power supply delivered from StarSBC-6ULL, paralelly connected to pin 2 of J1 | ||
| 3 | UART8-RXD | ENET2_TX_EN | B15 | RXD line of UART8 with RS485 level converter (J200), half-duplex, direction line GPIO3.26 |
| 4 | GND | |||
| 5 | UART8-TXD | ENET2_TX_DATA1 | A16 | TXD line of UART8 with RS485 level converter (J200), half-duplex, direction line GPIO3.26 |
| 6 | UART3-TXD | UART3_TX_DATA | H17 | TXD line of UART3 with RS232 level converter (J300) |
| 7 | - | - | - | |
| 8 | UART3-RXD | UART3_RX_DATA | H16 | RXD line of UART3 with RS232 level converter (J300) |
| 9 | GND | |||
| 10 | UART3-CTS | UART3_CTS | H15 | CTS line of UART3 with RS232 level converter (J300) |
| 11 | UART4-RXD | LCD_ENABLE | B8 | RXD line of UART4 with RS485 level converter (J200), half-duplex, direction line GPIO3.25 |
| 12 | UART3-RTS | UART3_RTS | G14 | RTS line of UART3 with RS232 level converter (J300) |
| 13 | UART4-TXD | LCD_CLK | A8 | TXD line of UART4 with RS485 level converter (J200), half-duplex, direction line GPIO3.25 |
| 14 | GND | |||
| 15 | - | - | - | |
| 16 | - | - | - | |
| 17 | - | - | - | |
| 18 | - | - | - | |
| 19 | - | - | - | |
| 20 | UART7-RXD | LCD_DATA16 | C13 | RXD line of UART3 with RS232 level converter (J301) |
| 21 | - | - | - | |
| 22 | UART7-TXD | LCD_DATA17 | B13 | TXD line of UART3 with RS232 level converter (J301) |
| 23 | - | - | - | |
| 24 | UART7-CTS | LCD_DATA07 | D11 | CTS line of UART3 with RS232 level converter (J301) |
| 25 | - | - | - | |
| 26 | UART7-RTS | LCD_DATA06 | A10 | CTS line of UART3 with RS232 level converter (J301) |
| J2 | ||||
| 1 | +3,3VO | +3,3V power supply delivered from StarSBC-6ULL, paralelly connected to pin 1 of J1 | ||
| 2 | +5V | 5V power supply delivered from StarSBC-6ULL, paralelly connected to pin 2 of J1 | ||
| 3 | - | - | - | |
| 4 | GND | |||
| 5 | - | - | - | |
| 6 | - | - | - | |
| 7 | GPIO3.17 | LCD_DATA12 | C12 | Pul-down 10k resistor optionally used for module ("hat") identification |
| 8 | - | - | - | |
| 9 | GND | |||
| 10 | - | - | - | |
| 11 | CAN1-TX | LCD_DATA08 | B11 | TX line of CAN1 with CAN-FD level converter (J100 and J101) |
| 12 | - | - | - | |
| 13 | CAN1-RX | LCD_DATA09 | A11 | RX line of CAN1 with CAN-FD level converter (J100 and J101) |
| 14 | GND | |||
| 15 | CAN2-TX | LCD_DATA10 | E12 | TX line of CAN2 with CAN-FD level converter (J100 and J101) |
| 16 | - | - | - | |
| 17 | CAN2-RX | LCD_DATA11 | D12 | RX line of CAN2 with CAN-FD level converter (J100 and J101) |
| 18 | - | - | - | |
| 19 | MQS-R | LCD_DATA22 | A14 | Not used by default |
| 20 | - | - | - | |
| 21 | MQS-L | LCD_DATA23 | B16 | Not used by default |
| 22 | - | - | - | |
| 23 | GPIO3.25 | LCD_DATA20 | C14 | RS485 semiduplex direction line (UART4) |
| 24 | - | - | - | |
| 25 | GPIO3.26 | LCD_DATA21 | B14 | RS485 semiduplex direction line (UART8) |
| 26 | - | - | - | |
LVDS (output) Pinout
| LVDS connector pin | Function name | Description |
|---|---|---|
| 1 | +5V | Power supply for external devices (max. 20 mA) Internally connected with pin 2 |
| 2 | +5V | Power supply for external devices (max. 20 mA) Internally connected with pin 1 |
| 3 | - | - |
| 4 | GND | - |
| 5 | GND | - |
| 6 | GND | - |
| 7 | D0n | LVDS D0n data line |
| 8 | D0p | LVDS D0p data line |
| 9 | D1n | LVDS D1n data line |
| 10 | D1p | LVDS D1p data line |
| 11 | D2n | LVDS D2n data line |
| 12 | D2p | LVDS D2p data line |
| 13 | GND | - |
| 14 | GND | - |
| 15 | CLKn | LVDS CLKn clock line |
| 16 | CLKp | LVDS CLKp clock line |
| 17 | D3n | LVDS D3n data line |
| 18 | D3p | LVDS D3p data line |
HDMI (output) Pinout
HDMI connector built-in SL-MIPI-LVDS-HDMI-CNV converter has standard HDMI pinout.
Dimensions
