VisionSOM imx-meta-somlabs
From SomLabs Wiki
VisionSOM imx-meta-somlabs layer for NXP Yocto
This tutorial explains how to build the Yocto zeus system for the VisionSOM modules. The Yocto system uses the following kernel and u-boot repositories:
- kernel (5.4.47): https://github.com/SoMLabs/somlabs-linux-imx/tree/somlabs_imx_5.4.47_2.2.0
- u-boot (2020.04): https://github.com/SoMLabs/somlabs-uboot-imx/tree/somlabs-imx_v2020.04_5.4.47_2.2.0
Introduction
Meta-somlabs is a layer providing the VisionSOM-6ULL with VisionCB-6ULL-STD carrier board and VisionSOM-8MM with VisionCB-8M boards hardware support for Yocto-based NXP Linux system.
Host system prerequisites
This tutorial was prepared for the Ubuntu 18.04.5 LTS host operating system. All of the files required for system image compilation may require up to 120 GB of the disk space. The SDK build requires additional 25 GB (145 GB in total).
The following packages need to be installed before the building process:
sudo apt-get install repo gawk wget git diffstat unzip texinfo gcc-multilib build-essential chrpath socat libsdl1.2-dev xterm sed cvs subversion coreutils texi2html docbook-utils python-pysqlite2 help2man make gcc g++ desktop-file-utils libgl1-mesa-dev libglu1-mesa-dev mercurial autoconf automake groff curl lzop asciidoc u-boot-tools
The source code will be obtained using git, so it needs to be configured by setting the user name and email with correctly set values:
git config --global user.email "you@example.com" git config --global user.name "Your Name"
System image
This layer should be used in order to build the imx-image-multimedia image. It includes the SoMLabs demo application using the GTK and GStreamer libraries.
Building the system image
The general description of the building process is described in the iMX Yocto Project User's Guide document:
https://www.nxp.com/docs/en/user-guide/IMXLXYOCTOUG.pdf
The summary of required steps including the meta-somlabs layer is shown below:
mkdir imx-yocto-bsp cd imx-yocto-bsp repo init -u https://source.codeaurora.org/external/imx/imx-manifest -b imx-linux-zeus -m imx-5.4.47-2.2.0.xml repo sync cd sources git clone -b zeus https://github.com/SoMLabs/imx-meta-somlabs.git meta-somlabs cd ../
The following lines need to be added at the end of the imx-yocto-bsp/imx-setup-release.sh file in order to add the meta-somlabs layer to build and enable the commercial license in build (for example with nano editor: nano imx-setup-release.sh):
echo "BBLAYERS += \"\${BSPDIR}/sources/meta-somlabs\"" >> $BUILD_DIR/conf/bblayers.conf
echo "LICENSE_FLAGS_WHITELIST = \"commercial\"" >> $BUILD_DIR/conf/local.conf
System building may be configured for one of the available machine configurations:
- visioncb-6ull-std-emmc-btwifi - VisionCB-6ULL-STD board with eMMC and wireless modem VisionSOM-6ULL version
- visioncb-6ull-std-emmc - VisionCB-6ULL-STD board with eMMC VisionSOM-6ULL version
- visioncb-6ull-std-sd-btwifi - VisionCB-6ULL-STD board with SD-card and wireless modem VisionSOM-6ULL version
- visioncb-6ull-std-sd - VisionCB-6ULL-STD board with SD-card VisionSOM-6ULL version
- visionsom-8mm-cb - VisionCB-8M board family with VisionSOM-8Mmini modules
System building may be started by the following commands (the first one needs to be called from the imx-yocto-bsp directory):
DISTRO=fsl-imx-wayland MACHINE=<SELECTED_MACHINE> source imx-setup-release.sh -b <BUILD_DIRECTORY> bitbake imx-image-multimedia
The system image is located in the imx-image-multimedia-<SELECTED_MACHINE>.wic.bz2 file in the tmp/deploy/images/<SELECTED_MACHINE> directory. It should be extracted and installed on a SD-card:
bunzip2 -dkf imx-image-multimedia-<SELECTED_MACHINE>.wic.bz2 sudo dd if=imx-image-multimedia-<SELECTED_MACHINE>.wic of=/dev/sdX bs=1M
The instruction for the eMMC memory image installation may be found on the following wiki pages:
