Personal tools

VisionCB-RT1176-STD v.1.2 Datasheet and Pinout

From SomLabs Wiki

Revision as of 13:50, 3 July 2024 by Piotrzbysinski (talk | contribs) (MIPI-DSI LCD connector (J501))
Jump to: navigation, search

VisionCB-RT1176-STD v.1.2 Datasheet and Pinout


General description

VisionCB-RT1176-STD.png


VisionCB-RT1176-STD is a carrier board for the VisionSOM-RT1170 family of computer-on-modules, which are powered by NXP i.MX RT117x application processors. The carrier board, together with a System on Module (SoM), makes a complete development platform similar to SBC. The carrier board houses the most common interfaces such as audio codec, USB, Ethernet, UART, RS485, CAN etc. A large variety of interfaces allows to use it as both a complete development platform or as a stand-alone end-product.

The carrier board connects with the SoM via a standard SODIMM connector.

Applications

  • Digital cluster
  • Home Control Panel
  • Home Automation – Smart Home
  • Human-machine Interfaces (HMI)
  • Point-of-sales (POS) terminals
  • Motor Drives
  • 2D barcode scanners and printers
  • Smart grid infrastructure
  • IoT gateways
  • Transport ticketing
  • PV Energy Generation
  • Robotic appliance
  • Fitness/outdoor equipment

Features

  • Carrier Board (Base Board) compatible with the VisionSOM family of modules based on NXP i.MX RT117x application processors
  • SoM connector: SODIMM200
  • Expansion Connectors:
    • GPIO-SNVS, GPIO-COMM1, GPIO-COMM2 2x16 Pin Headers (Male)
    • MicroSD socket
  • Audio:
    • 24-bit codec audio with headphones and microphone Jack connector
  • Communication Connectors:
    • 1x JTAG connector
    • RS485 half-duplex
    • CAN single channel
    • 1x Ethernet 10/100/1000 Mbit/s, RJ45
    • 1x USB Host Type A connectors
    • 1x USB-OTG Micro AB connector
    • 1x Console MicroUSB B connector (Mbed SWDAP debug probe based on LPC11U35FHI33/501)
  • Display Interface: 30-pin FFC/FPC MIPI-DSI
  • Camera Interface: 30-pin FFC/FPC MIPI-CSI
  • User Interface:
    • 5 Pushbuttons
    • 5 LEDs
  • Recovery jumper
  • Power Supply
    • DC connector: Input Voltage 9-12V DC (5.5x2.1 connector)
    • CR2032 battery socket for RTC
  • Temperature Range: 0 to +70°C
  • Board Size: 145mm x 90mm x 22mm

Pictures of VisionCB-RT1176-STD v1.2 board

Version Photo
VisionCB-RT1176-STD v1.2 board with attached SOM
VisionCB-RT1176-STD.png

Ordering info

VisionCB-RT1176-STD v1.2

Block Diagram

VisionCB-RT1176-STD-block-diagram.png

Electrical parameters

Parameter Value Units Comment
Min. Typ. Max.
Power Supply (J100 input) 9.0 12.0 15.0 V Positive pole on central connector of J100
Supply current - - 0.15 A Excluding LCD, USB and antoher external loads
Output voltage (VCC-3V3) - 3.3 - V Generated by internal LDO
Output VCC-3V3 current - - 500 mA Generated by internal LDO
USB power supply 4.75 4.9 5.5 V On J201 (Linux USB console connector)
Input GPIO voltage (J405) 0 - 3.3 V LCD-RGB connector
Input GPIO voltage (J504) 0 - 3.3 V Raspberry Pi compatible
Input GPIO voltage (J502, J503) 0 - 3.3/5 (1) V Arduino compatible connector (digital I/O)
Input GPIO voltage (J501) 0 - 3.3 V Arduino compatible connector (analog inputs)

Note:
1. Depends on JP3 selector.

Recovery Jumper/MCU Boot Configuration

VisionCB-RT1176-STD-recovery.png

RECOVERY is the boot mode selector. If:

  • RECOVERY = 0 (jupmer installed) then BOOT-MODE0 = 1, as a result serial loader starts
  • RECOVERY = 1 (jumper is not installed) or open then BOOT-MODE0 = 0, as a result MCU boots from fuses

External JTAG Connector

VisionCB-RT1176-STD-JTAG.png
JTAG Connector Default function name MCU pin name
1 +3V3 -
2 TMS GPIO_LPSR_15
3 GND NA
4 TCK GPIO_LPSR_14
5 GND NA
6 TDO GPIO_LPSR_11
7 - -
8 TDI GPIO_LPSR_12
9 GND GPIO_AD_B0_07
10 nRES/TRST GPIO_LPSR_10

DAP Debug Interface

VisionCB-RT1176-STD-swdap.png

The DAP debug interface is based on LPC11U35FHI33/501 and converts USB into two-lines SWD debug interface.
The DAP debug interface also serves as an vCOM (on USB) interface for optional UART console port.

SWDIO DAP Connector

VisionCB-RT1176-STD-swdap-jtag-conn.png
DAP Connector Function name Source: DAP/SoM
1 nRES DAP
2 nRESET DAP
3 SWCLK DAP
4 TCK SoM
5 SWDIO DAP
6 TMS SoM

Note:
1. During normal use, it is recommended to connect pin pairs: 1-2, 3-4, 5-6.


Console DAP Connector

VisionCB-RT1176-STD-swdap-console-conn.png
DAP Connector Function name Signal Source
1 RxD DAP
2 UART2.RxD SoM
3 TxD DAP
4 UART2.TxD SoM

Note:
1. During normal use, it is recommended to connect pin pairs: 1-2, 3-4.

GPIO COMM1 I/O header (J802)

VisionCB-RT1176-STD-con-comm1.png


J802 Pin Default function name MCU pin name Description
1 SPI4.SCK GPIO_DISP_B2_12 3.3V logic levels
2 SPI4.OUT GPIO_DISP_B2_14 3.3V logic levels
3 SPI4.IN GPIO_DISP_B2_13 3.3V logic levels
4 SPI4.CS0 GPIO_DISP_B2_15 3.3V logic levels
5 I2C1.SDA GPIO_AD_33 External 4,7k pull-up resistor
6 I2C1.SCL GPIO_AD_32 External 4,7k pull-up resistor
7 I2C2.SDA GPIO_AD_19 External 4,7k pull-up resistor
8 I2C2.SCL GPIO_AD_18 External 4,7k pull-up resistor
9 CAN2.TX GPIO_AD_00 3.3V logic levels
10 CAN2.RX GPIO_AD_01 3.3V logic levels
11 UART1.RXD GPIO_AD_25 Available to the user as GPIO only in SoM without 1DX radio modules.
12 UART1.TXD GPIO_AD_24 Available to the user as GPIO only in SoM without 1DX radio modules.
13 UART1.CTS GPIO_AD_26 Available to the user as GPIO only in SoM without 1DX radio modules.
14 UART1.RTS GPIO_AD_27 Available to the user as GPIO only in SoM without 1DX radio modules.
15 +3V3 NA -
16 GND NA -

Notes:
1. NA - not available.


GPIO COMM2 I/O header (J801)

VisionCB-RT1176-STD-con-comm2.png


J801 Pin Default function name MCU pin name Description
1 UART5.TXD GPIO_AD_28 3.3V logic levels
2 UART3.TXD GPIO_AD_30 3.3V logic levels
3 UART5.RXD GPIO_AD_29 3.3V logic levels
4 UART3.RXD GPIO_AD_31 3.3V logic levels
5 UART10.TXD GPIO_AD_15 Pushbutton S804 is connected to this line.
6 UART12.TXD GPIO_LPSR_00 GPIO_LPSR00 LED is connected to this line (through logic inverter).
7 UART10.RXD GPIO_AD_16 Pushbutton S803 is connected to this line.
8 UART12.RXD GPIO_LPSR_01 GPIO_LPSR01 LED is connected to this line (through logic inverter).
9 UART10.RTS GPIO_AD_35 Pushbutton S802 is connected to this line.
10 UART12.RTS GPIO_LPSR_04 GPIO_LPSR04 LED is connected to this line (through logic inverter).
11 UART10.CTS GPIO_AD_34 Pushbutton S801 is connected to this line.
12 UART12.CTS GPIO_LPSR_05 GPIO_LPSR05 LED is connected to this line (through logic inverter).
13 NC - -
14 DAC-OUT DAC-OUT 12-bit DAC voltage output (range 0-1.8V).
15 +3V3 NA -
16 GND NA -

Notes:
1. NA - not available.
2. NC - not connected.


GPIO SNVS I/O header (J800)

VisionCB-RT1176-STD-con-snvs.png


J800 Pin Default function name MCU pin name Description
1 GPIO-SVNS.9 GPIO_SNVS_09 1.75V VDD_SNVS_ANA power domain
2 GPIO-SVNS.8 GPIO_SNVS_08 1.75V VDD_SNVS_ANA power domain
3 GPIO-SVNS.7 GPIO_SNVS_07 1.75V VDD_SNVS_ANA power domain
4 GPIO-SVNS.6 GPIO_SNVS_06 1.75V VDD_SNVS_ANA power domain
5 GPIO-SVNS.5 GPIO_SNVS_05 1.75V VDD_SNVS_ANA power domain
6 GPIO-SVNS.4 GPIO_SNVS_04 1.75V VDD_SNVS_ANA power domain
7 GPIO-SVNS.3 GPIO_SNVS_03 1.75V VDD_SNVS_ANA power domain
8 GPIO-SVNS.2 GPIO_SNVS_02 1.75V VDD_SNVS_ANA power domain
9 GPIO-SVNS.1 GPIO_SNVS_01 1.75V VDD_SNVS_ANA power domain
10 GPIO-SVNS.0 GPIO_SNVS_00 1.75V VDD_SNVS_ANA power domain
11 PMIC-STBY-REQ PMIC-STBY-REQ 1.75V VDD_SNVS_ANA power domain.
12 RESET RESET POR-B of MCU line (resets all of the chip except the Secure Non-Volatile Storage (SNVS) block), active low.
1.75V VDD_SNVS_ANA power domain.
13 WAKEUP - A GPIO powered by SNVS domain power supply which can be configured as wakeup source in SNVS mode.
1.75V VDD_SNVS_ANA power domain.
14 ON-OFF ON-OFF A brief connection to GND in the OFF mode causes the internal power management state machine to change the state to ON.
In the ON mode, a brief connection to GND generates an interrupt intended to be a software-controllable power-down).
Approximately five seconds (or more) to GND causes a forced OFF.
Both boot mode inputs can be disconnected.
1.75V VDD_SNVS_ANA power domain.
15 +1V8 NA Reference voltage for 1V8 peripherals.
16 GND NA -

Notes:
1. NA - not available.

User LEDs connections

VisionCB-RT1176-STD-ui-LED.png


LED PCB designation MCU pin name Description
D804 SYS JTAG.MOD JTAG.MOD input with internal pull-down by 10 kOhm resistor.
D803 GPIO_LPSR_00 UART12.TXD Line connected to J801 (GPIO COMM2).
D802 GPIO_LPSR_01 UART12.RXD Line connected to J801 (GPIO COMM2).
D801 GPIO_LPSR_04 UART12.RTS Line connected to J801 (GPIO COMM2).
D800 GPIO_LPSR_05 UART12.CTS Line connected to J801 (GPIO COMM2).

Notes:
1. LEDs are switched on by logic „1” set at the GPIO outputs.
2. LEDs are controlled by current drivers and do not load the GPIOs.

VisionCB-RT1176-STD-ui-SYSLED.png
LED PCB designation MCU pin name Description
D804 SYS JTAG.MOD JTAG.MOD input with internal pull-down by 10 kOhm resistor.

User switches connections

VisionCB-RT1176-STD-ui-pb.png


Switch PCB designation MCU pin name Description
S804 UART10.TXD GPIO_AD_15 Line connected to J801 (GPIO COMM2) connector.
S803 UART10.RXD GPIO_AD_16 Line connected to J801 (GPIO COMM2) connector.
S802 UART10.RTS GPIO_AD_35 Line connected to J801 (GPIO COMM2) connector.
S801 UART10.CTS GPIO_AD_34 Line connected to J801 (GPIO COMM2) connector.

Notes:
1. After button pressing on GPIO lines are set to „0”.
2. GPIO lines connected to switches are separated from board’s environment by 100R resistors.
3. The function of red pushbutton is main system reset (connected to RESET-IN SoM input).

MIPI-DSI LCD connector (J501)

VisionCB-RT1176-STD-DSI.png


J501 pin Default function name MCU pin name
1 GND -
2 DSI.CLK_P MIPI_DSI_CKP
3 DSI.CLK_N MIPI_DSI_CKN
4 GND -
5 DSI.DATA0_P MIPI_DSI_DP0
6 DSI.DATA0_N MIPI_DSI_DN0
7 GND -
8 DSI.DATA1_P MIPI_DSI_DP1
9 DSI.DATA1_N MIPI_DSI_DN1
10 GND -
11 NC -
12 NC -
13 GND -
14 NC -
15 NC -
16 GND
17 I2C6.SCL1,3 GPIO_LPSR_07
18 I2C6.SDA1,3 GPIO_LPSR_06
19 GND -
20 DSI-DISP-RST2 GPIO5-09 (GPIO_DISP_B2_08)
21 TP-INT2 GPIO5-02 (GPIO_DISP_B2_01)
22 TP-RST2 GPIO5-01 (GPIO_DISP_B2_00)
23 GND -
24 VDD-3V3 -
25 VDD-3V3 -
26 VDD-5V0 -
27 VDD-5V0 -
28 DSI-BL-PWM2 GPIO3-13 (GPIO_AD_14)
29 DSI-BL-EN2 GPIO5-10 (GPIO_DISP_B2_09)
30 GND -

Notes:
1. Both lines pull-upped to 3.3V with 4,7kOhm resistors.
2. In series - between GPIO lines and connector pins - 100 Ohm resistors are included.
3. The I2C6 interface is shared with CSI input.

MIPI-CSI camera connector (J500)

VisionCB-RT1176-STD-CSI.png


J500 pin Default function name MCU pin name
1 GND -
2 CSI.CLK_P MIPI_CSI_CKP
3 CSI.CLK_N MIPI_CSI_CKN
4 GND -
5 CSI.DATA0_P MIPI_CSI_DP0
6 CSI.DATA0_N MIPI_CSI_DN0
7 GND -
8 CSI.DATA1_P MIPI_CSI_DP1
9 CSI.DATA1_N MIPI_CSI_DN1
10 GND -
11 NC -
12 NC -
13 GND -
14 NC -
15 NC -
16 GND
17 I2C6.SCL1, 3 GPIO_LPSR_07
18 I2C6.SDA1, 3 GPIO_LPSR_06
19 GND -
20 DSI-DISP-RST2 GPIO5-09 (GPIO_DISP_B2_08)
21 TP-INT2 GPIO5-02 (GPIO_DISP_B2_01)
22 TP-RST2 GPIO5-01 (GPIO_DISP_B2_00)
23 GND -
24 VDD-3V3 -
25 VDD-3V3 -
26 VDD-5V0 -
27 VDD-5V0 -
28 DSI-BL-PWM2 GPIO3-13 (GPIO_AD_14)
29 DSI-BL-EN2 GPIO5-10 (GPIO_DISP_B2_09)
30 GND -

Notes:
1. Both lines pull-upped to 3.3V with 4,7kOhm resistors.
2. In series - between GPIO lines and connector pins - 100 Ohm resistors are included.

Dimensions

VisionCB-RT-STD-1-0-PCB-size.png

NXP Partner ST Partner Renesas Partner