StarSBC-6ULL Datasheet and Pinout

StarSBC-6ULL Datasheet and Pinout

---

General description

The StarSBC-6ULL SBC (Single Board Computer) is small but powerful IoT Sensor Hub, optimized for operation in applications requiring a large number of communication interfaces. The StarSBC-6ULL is equipped with on-board PHY 10/100 Mb/s Ethernet interface, Murata 1DX radio module (integrated WiFi/BLE), USB host and USB-OTG interfaces. The StarSBC-6ULL supports connections to a variety of interfaces: I2C, SPI, UART and CAN. Additionally the StarSBC-6ULL module is equipped with easy to use 2×26 pin connectors with 40 GPIOs for any use in user application.

The StarSBC-6ULL can be optionally equipped with communication expander module SLH2-comm, which is equipped with 2 x CAN, 2 x RS485, 2 x RS232 physical layers interfaces.

The StarSBC-6ULL supports industrial grade embedded applications.

Applications

• IoT Sensor Hubs
• Home Appliances
• IoT gateways
• Protocol converters
• Home Automation – Smart Home
• Point-of-sales (POS) terminals
• Cash Register
• 2D barcode scanners and printers
• Smart grid infrastructure
• Residential gateways
• Outdoor equipment

Features

• Powered by NXP i.MX 6ULL application processor
• Core clock up to 900MHz
• Up to 1GB RAM DDR3L
• Up to 32GB eMMC
• Optional Murata 802.11b/g/n Wi-Fi and Bluetooth v5.1 module
• Power-efficient and cost-optimized solution
• Ideal for industrial IoT and embedded applications
• Integrated security features

Pictures of SBC versions

Version	Photo
eMMC

Wi-Fi and Ethernet PHY10/100 are available as an options.

Ordering info

SLS06Y2_Clock_RamSize_FlashSize_SF_TEMP

SLS	Product type SLS - System on Module
0	SOM Name 0 - StarSOM board-to-board connectors
6	CPU Family 6 - i.MX6
Y2	CPU Type Y2 - i.MX6 ULL Y2
Clock	CPU Clock Speed 528C - 528MHz 792C - 792MHz 900C - 900MHz
RamSize	DDR3 RAM Size 128R - 128MB 256R - 256MB 512R - 512MB
FlashSize	Flash Size Type and Density 04GE - 4GB eMMC 08GE - 8GB eMMC 16GE - 16GB eMMC 32GE - 32GB eMMC
SF	Special Features 0SF - No Special Features 1WB - Built-in Murata 802.11b/g/n Wi-Fi and Bluetooth v5.1 Module 2ET - Built-in Microchip 100Mb Ethernet PHY 3WE - Built-in Murata 802.11b/g/n Wi-Fi/Bluetooth v5.1 and Microchip 100Mb Ethernet PHY
TEMP	Operating Temperature C - Consumer: 0 to +70 C E - Extended with Wi-Fi: -25 to +70 C I - Industrial: -40 to +85 C

Block Diagram

Operating ranges

Parameter	Value	Unit	Comment
Power Supply	5	V	Connected to J100 or J101 or USB conenctors
Input GPIO voltage	3.3	V	-
Environment temperature1	-40…+85	oC	Industrial range w/o WiFi module
	-25…+70		Industrial (extended) range with WiFi module
	0…+70		Consumer range

Note:
1. Maximum MPU junction temperature is +105^oC (industrial version) or +95^oC (consumer version).

Electrical parameters

SOM signal name	Parameter	Value			Units
		Min.	Typ.	Max.
+3V3IN	Supply Voltage	3.15	3.3	3.45	V
+3V3IN	Total Supply Current1	-	175	255	mA
VGPIO	GPIO Input Voltage	0	3.3	3.62	V
+3V3SW	Output current of 3.3V power supply for peripherals	-	-	0.2	A
USB-OTGx-VBUS	USB Supply	4.40	-	5.5	V
VDD-COIN-3V	SNVS Backup Battery Supply	2.66	-	3.6	V
-	ADC Inputs Voltage	0	-	3.3	V

Notes:
1. Excluding external load connected to +3.3VOUT lines.
2. Applying the maximum voltage 3.6V results in shorten lifetime. Recommended value is smaller than 3.5V.

Features

• x

Connector pin number	Default function	GPIO	Ball numer BGA289	Notes
J100
1	+3,3VO			+3,3V power output (max. 100 mA) - paralelly connected to pin 1 of J101
2	+5V			External power supply (power source) 5V - paralelly connected to pin 2 of J101
3	UART8-RXD	ENET2_TX_EN	B15
4	GND
5	UART8-TXD	ENET2_TX_DATA1	A16
6	UART3-TXD	UART3_TX_DATA	H17
7	PWM5	LED_DATA18	A13
8	UART3-RXD	UART3_RX_DATA	H16
9	GND
10	UART3-CTS	UART3_CTS	H15
11	UART4-RXD	LCD_ENABLE	B8
12	UART3-RTS	UART3_RTS	G14
13	UART4-TXD	LCD_CLK	A8
14	GND
15	I2C4-SDA	LCD_DATA02	E10	In I2C mode external pull-up resistor is necessary (no any internal pull-up)
16	I2C3-SDA	LCD_DATA00	B9	In I2C mode external pull-up resistor is necessary (no any internal pull-up)
17	I2C4-SCL	LCD_DATA03	D10	In I2C mode external pull-up resistor is necessary (no any internal pull-up)
18	I2C3-SCL	LCD_DATA01	A9	In I2C mode external pull-up resistor is necessary (no any internal pull-up)
19	ECSPI2-MOSI	UART5_TX_DATA	F17
20	UART7-RXD	LCD_DATA16	C13
21	ECSPI2-MISO	UART5_RX_DATA	G13
22	UART7-TXD	LCD_DATA17	B13
23	ECSPI2-SCLK	UART4_TX_DATA	G17
24	UART7-CTS	LCD_DATA07	D11
25	ECSPI2-CS	UART4_RX_DATA	G16
26	UART7-RTS	LCD_DATA06	A10
J101
1	+3,3VO			+3,3V power output (max. 100 mA) - paralelly connected to pin 1 of J100
2	+5V			External power supply (power source) 5V - paralelly connected to pin 2 of J100
3	USB1-DP			Line connected to USB1 channel through MUX (output ENET2_RX_ER, ball D16 is USB1 connection selector). Connected to USB1-DP MPU line if ENET2_RX_ER="0" (USB1-SEL), in another case USB1-DP MPU line is connected to MicroUSB connector (USB-OTG).
4	GND
5	USB1-DM			Line connected to USB1 channel through MUX (output ENET2_RX_ER, ball D16 is USB1 connection selector). Connected to USB1-DM MPU line if ENET2_RX_ER="0" (USB1-SEL), in another case USB1-DM MPU line is connected to MicroUSB connector (USB-OTG).
6	GPIO-6	GPIO1_IO06	K17
7	GPIO3.17	LCD_DATA12	C12
8	GPIO-7	GPIO1_IO07	L16
9	GND
10	GPIO-8	GPIO1_IO08	N17
11	CAN1-TX	LCD_DATA08	B11
12	GPIO-9	GPIO1_IO09	M15
13	CAN1-RX	LCD_DATA09	A11
14	GND
15	CAN2-TX	LCD_DATA10	E12
16	GPIO3.2	LCD_HSYNC	D9
17	CAN2-RX	LCD_DATA11	D12
18	GPIO3.3	LCD_VSYNC	C9
19	MQS-R	LCD_DATA22	A14
20	UART2-RXD	UART2_RX_DATA	J16
21	MQS-L	LCD_DATA23	B16
22	UART2-TXD	UART2_TX_DATA	J17
23	GPIO3.25	LCD_DATA20	C14
24	UART2-CTS	UART2_CTS	J15
25	GPIO3.26	LCD_DATA21	B14
26	UART2-RTS	UART2_RTS	H14
J102
1	UART1-TXD	UART1_TX_DATA	K14	TxD line of Linux console port (LV-TTL logic levels)
2	UART1-RXD	UART1_RX_DATA	K16	RxD line of Linux console port (LV-TTL logic levels)
3	GND
Another functions
	BUZZER	GPIO1_IO05	M17	Electromagnetic speaker control output (thru NPN driver)
	SYSLED	ENET2_TX_CLK	D17	System or user LED control output (heartbeat by default, thru NPN driver)
	USRLED	LCD_DATA14	A12	User LED control output (thru NPN driver)
	WDOG-B	LCD_RESET	E9	Used by system, do not modify default configuration
	ENET-MDIO	ENET2_RX_DATA0	C17
	ENET-MDC	ENET2_RX_DATA1	C16
	ENET1-RST	ENET2_RX_EN	B17
	ENET1-INT	ENET2_TX_DATA0	A15
	USB1-SEL	ENET2_RX_ER	D16
	USB1-ID	GPIO1_IO00	K13
	USB1-VBUS-OC	GPIO1_IO01	L15
	USB1-VBUS-EN	GPIO1_IO04	M16
	USB2-VBUS-OC	GPIO1_IO03	L17
	USB2-VBUS-EN	GPIO1_IO02	L14
WiFi and BLE module connection
	BT-ENABLE	CSI_MCLK	F5
	WLAN-HWAKE	CSI_PIXCLK	E5
	BT-HWAKE	CSI_VSYNC	F2
	BT-WAKE	CSI_HSYNC	F3
	BT-RXD	CSI_DATA00	E4	UART5
	BT-TXD	CSI_DATA01	E3	UART5
	BT-RTS	CSI_DATA02	E2	UART5
	BT-RTS	CSI_DATA03	E1	UART5
	BT-PCM-SYNC	CSI_DATA04	D4
	BT-PCM-CLK	CSI_DATA05	D3
	BT-PCM-OUT	CSI_DATA06	D2
	BT-PCM-IN	CSI_DATA07	D1
	CLK32kHz	JTAG_CTK	M14	Clock output to 1DX radio module (WiFi/BLE)
	JTAG_MOD	JTAG_MOD	P15	Permanently connected to GND
	BOOT_MODE1	BOOT_MODE1	U10	Permanently connected to GND } Dimensions