SL-MIPI-CSI-OV5640 Datasheet and Pinout
From SomLabs Wiki
SL-MIPI-CSI-OV5640 5Mpx camera module with MIPI-CSI interface and OV5640 video sensor Datasheet and Pinout
General description
SL-MIPI-CSI-OV5640 is the 5 Mpx color camera module. Module is equipped with MIPI-CSI interface and FPC30 connector therefore SL-MIPI-CSI-OV5640 module is matched to the SoMLabs carrier boards.
The SL-MIPI-CSI-OV5640 is equipped with OV5640 hi-res HD 5 Mpx CMOS video sensor. Video interface is dual lane MIPI-CSI interface and module supports electronic shutter mode: rolling shutter/frame exposure.
As a result of using advanced PMIC – SL1 – developed by SoMLabs, the SL-MIPI-CSI-OV5640 module is powered from single +3.3V line available in FPC connector.
The SL-MIPI-CSI-OV5640 is fully compatible with SoMLabs carrier boards equipped with MIPI-CSI connectors. By default SL-MIPI-CSI-OV5640 module is equipped with fish-eye (120º) lens.
Features
- Based on OV5640 CMOS video chip
- Resolution 2592 x 1944 px
- Fish-eye lens (120º)
- Output formats: 8/10-b RGB RAW
- MIPI-CSI interface (2 lanes)
- Typical frame rates:
- QSXGA (2592×1944): 15 fps
- 1080p: 30 fps
- 1280×960: 45 fps
- 720p: 60 fps
- VGA (640×480): 90 fps
- QVGA (320×240): 120 fps
- Shutter: rolling/frame exposure
- Single rail +3.3V power supply
- Configuration via I2C
- Operating temperature -30÷+70°C
- Fully compatible with SoMLabs carrier boards equippped with MIPI-CSI interface (FPC30 connector)
- Built-in clock source
- Built-in SL1 PMIC (developed by SoMLabs)
- Connection with carrier board using FPC30 cable
Pictures
Ordering info
SL-MIPI-CSI-OV5640 - FPC 30-pin flat cable (A-A) is included.
Operating ranges
| Parameter | Value | Unit | Comment |
|---|---|---|---|
| Power Supply | Powered from carrier board | ||
| Current | Maximum peak value | ||
| Environment temperature | oC | - |
Electrical parameters
| Signal name | Parameter | Value | Units | ||
|---|---|---|---|---|---|
| Min. | Typ. | Max. | |||
| +5V | Supply Voltage | 4.75 | 5.0 | 5.25 | V |
| +3.3V | Supply Voltage | 3.2 | 3.3 | 3.35 | V |
| I5V | Supply Current (5V) | 40 | 80 | 100 | mA |
| I3.3V | Supply Current (3.3V) | 1 | 2.2 | 8 | mA |
| VIOI2C | I2C Input Voltage | 0 | 3.3 | 3.6 | V |
| VIORES/SPDIF | RES/SPDIF Input Voltage | 0 | 3.3 | 3.6 | V |
| fI2C | I2C Controller Speed | - | - | 400 | kHz |
| RINT | Interrupt Output Pull-up Resistance | - | 4.7 | - | kΩ |
| RI2C | I2C IOs Pull-up Resistance | - | 4.7 | - | kΩ |
MIPI-CSI (output) Pinout
| FPC30 connector pin | Function name | Description |
|---|---|---|
| 1 | GND | - |
| 2 | - | - |
| 3 | HPD | HPD line from HDMI (voltage translated to 3.3V) |
| 4 | +5V | Power supply (input) |
| 5 | +5V | Power supply (input) |
| 6 | +3.3V | Power supply (input) |
| 7 | +3.3V | Power supply (input) |
| 8 | GND | - |
| 9 | SPDIF-TX | SPDIF input from SBC |
| 10 | INT | Interrupt output (voltage translated to 3.3V) |
| 11 | RESET | Reset input (voltage translated to 3.3V) |
| 12 | GND | - |
| 13 | SDA | I2C SDA line (voltage translated to 3.3V) |
| 14 | SCL | I2C SCL line (voltage translated to 3.3V) |
| 15 | GND | - |
| 16 | D3n | MIPI-DSI lane 3 negative line |
| 17 | D3p | MIPI-DSI lane 3 positive line |
| 18 | GND | - |
| 19 | D2n | MIPI-DSI lane 2 negative line |
| 20 | D2p | MIPI-DSI lane 2 positive line |
| 21 | GND | - |
| 22 | D1n | MIPI-DSI lane 1 negative line |
| 23 | D1p | MIPI-DSI lane 1 positive line |
| 24 | GND | - |
| 25 | D0n | MIPI-DSI lane 0 negative line |
| 26 | D0p | MIPI-DSI lane 0 positive line |
| 27 | GND | - |
| 28 | CLKn | MIPI-DSI clock negative line |
| 29 | CLKp | MIPI-DSI clock positive line |
| 30 | GND | - |
HDMI (output) Pinout
HDMI connector built-in SL-MIPI-LVDS-HDMI-CNV converter has standard HDMI pinout.
Dimensions
