SL-MIPI-CSI-OV5640 Datasheet and Pinout
From SomLabs Wiki
SL-MIPI-CSI-OV5640 5Mpx camera module with MIPI-CSI interface and OV5640 video sensor Datasheet and Pinout
General description
SL-MIPI-CSI-OV5640 is the 5 Mpx color camera module. Module is equipped with MIPI-CSI interface and FPC30 connector therefore SL-MIPI-CSI-OV5640 module is matched to the SoMLabs carrier boards.
The SL-MIPI-CSI-OV5640 is equipped with OV5640 hi-res HD 5 Mpx CMOS video sensor. Video interface is dual lane MIPI-CSI interface and module supports electronic shutter mode: rolling shutter/frame exposure.
As a result of using advanced PMIC – SL1 – developed by SoMLabs, the SL-MIPI-CSI-OV5640 module is powered from single +3.3V line available in FPC connector.
The SL-MIPI-CSI-OV5640 is fully compatible with SoMLabs carrier boards equipped with MIPI-CSI connectors. By default SL-MIPI-CSI-OV5640 module is equipped with fish-eye (120º) lens.
Features
- Based on OV5640 CMOS video chip
- Resolution 2592 x 1944 px
- Fish-eye lens (120º)
- Output formats: 8/10-b RGB RAW
- MIPI-CSI interface (2 lanes)
- Typical frame rates:
- QSXGA (2592×1944): 15 fps
- 1080p: 30 fps
- 1280×960: 45 fps
- 720p: 60 fps
- VGA (640×480): 90 fps
- QVGA (320×240): 120 fps
- Shutter: rolling/frame exposure
- Single rail +3.3V power supply
- Configuration via I2C
- Operating temperature -30÷+70°C
- Fully compatible with SoMLabs carrier boards equippped with MIPI-CSI interface (FPC30 connector)
- Built-in clock source
- Built-in SL1 PMIC (developed by SoMLabs)
- Connection with carrier board using FPC30 cable
Note: fish-eye camera lens distorts the picture perspective. Example below.
Pictures
Ordering info
SL-MIPI-CSI-OV5640 - FPC 30-pin flat cable (A-A) is included.
Operating ranges
Parameter | Value | Unit | Comment |
---|---|---|---|
Power Supply | Powered from carrier board | ||
Current | Maximum peak value | ||
Working temperature | oC | - |
Electrical parameters
Signal name | Parameter | Value | Units | ||
---|---|---|---|---|---|
Min. | Typ. | Max. | |||
+3.3V | Supply Voltage | 3.2 | 3.3 | 3.35 | V |
I3.3V | Supply Current (3.3V) | 0.11 | .16 | - | mA |
tPWRSEQ | PMIC power-up time | - | 150 | - | ms |
VIO | I2C, RES, PWDN Input Voltage | 0 | 3.3 | 3.5 | V |
fI2C | I2C Controller Speed | - | - | 400 | kHz |
RI2C | I2C IOs Pull-up Resistance | - | 10 | - | kΩ |
RPWDN | Serial resistors voltage divider connected between FPC30 pin and PWDN input of OV5640 sensor | - | 2x10 | - | kΩ |
MIPI-CSI (output) Pinout
FPC30 connector pin | Function name | Description |
---|---|---|
1 | GND | - |
2 | - | - |
3 | - | - |
4 | - | - |
5 | - | - |
6 | +3.3V | Power supply |
7 | +3.3V | Power supply |
8 | GND | - |
9 | - | - |
10 | PWDN | OV5640 - Power Down input (active high, internal pull-down) |
11 | RESET | OV5640 - Reset input (active low, internal pull-up) |
12 | GND | - |
13 | SIOD_C | SCL line of configuration I2C interface (internal pull-up) |
14 | SIO_D | SDA line of configuration I2C interface (internal pull-up) |
15 | GND | - |
16 | - | - |
17 | - | - |
18 | GND | - |
19 | - | - |
20 | - | - |
21 | GND | - |
22 | MDN1 | CSI_DATA1_n |
23 | MDP1 | CSI_DATA1_p |
24 | GND | - |
25 | MDN0 | CSI_DATA0_n |
26 | MDP0 | CSI_DATA0_p |
27 | GND | - |
28 | MCN | CSI_CLK_n |
29 | MCP | CSI_CLK_p |
30 | GND | - |
Dimensions